ChipFind - документация

Электронный компонент: FH27-10S-0.4SH

Скачать:  PDF   ZIP
1
0.4 mm Contact Pitch, 1.2 mm above the board, Flexible Printed Circuit ZIF Connectors
FH 27 Series
NEW
NEW
2004.7
s
Overview
Continuous miniaturization of personal mobile devices
created a need for a low profile, high density interconnection
system.In the same time, the demand for higher currents and
higher reliability Flexible Printed Circuits has also increased.
Hirose meets all these challenges with introduction of this connector.
s
Features
1. Low profile, small PCB mounting area, weight reduction
Protruding only 1.2 mm above the board the connector
occupies 50% less area than comparable type having
contacts spaced on 0.5 mm centers.
Creative design, coupled with high manufacturing capabilities
resulted in extremely low weight of the connector.
2. Higher current carrying capacity
Contact spacing of 0.4 mm allows production of wider
and simpler pattern of conductive traces on FPC.
3. FPC temporary hold and verification of correct insertion
The connector has built-in FPC hold protrusions allowing
the tactile feel of the correct FPC insertion and holding it
in position before closing of the actuator.
4. Uses standard 0.2 mm thick FPC
5. One-finger operation of the actuator
Proven (in several other Hirose's connectors!) Flip-Lock
rotating actuator assures reliable mechanical and electrical
connection with FPC, confirming it with a definite tactile feel.
6. Board placement with automatic equipment
Flat top surface and packaging on the tape-and reel
allows the use of vacuum nozzles.
Standard reel contains 2,500 connectors.
7. Environmental considerations
The center cores of the embossed tape reels are made of Styrofoam.
8. Variety of contact positions
Available with 10, 40, 54, 57 and 60 pos.
s
Applications
Mobile phones, PDA's, digital cameras, digital video
cameras, LCD connections, plasma displays (PDP), camera
modules and other compact devices requiring Flexible
Printed Circuit connections using high reliability ultra-small
profile connectors
qWider FPC conductive traces
0.4 mm pitch FPC
0.3 mm pitch FPC
qFPC temporary retention
Metal fittings on each
side do not protrude
out allowing side-by-
side mounting of the
connectors or closer
component placement.
1.2mm
4.0mm
24.2mm
qFPC thickness: 0.20.03 mm
q1.2 mm Height, actuator fully closed.
(54 pos. shown)
0.27mm
0.4mm
0.1mm
0.3mm
Temporary hold-FPC
fully inserted
FPC temporary
hold protrusion
FPC notch
Metal
fitting
2
Item
Specification
Conditions
s
Materials
s
Ordering information
Part
Insulator
Actuator
Contacts
Metal fittings
LCP
LCP
Phosphor bronze
Phosphor bronze
Color: Black
Color: Dark brown
Tin-lead plated (Note 3)
Tin plated(No-lead)
UL94V-0
---------------
---------------
---------------
Material
Finish
Remarks
s
Product Specifications
Rating
Rated current 0.4 A DC
Rated voltage 40 V AC
Operating temperature range
-55 to +85 (Note 1)
Operating humidity range
Relative humidity 90% max. (No condensation)
Storage temperature range
-10 to +50 (Note 2)
Storage humidity range
Relative humidity 90% max.
Recommended FPC
Thickness: = 0.20.03mm tin-lead plated (Note 3)
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.
Note 3: When using FPC with gold plated contact pads the connector contacts must be also gold plated : Select the (05) plating code.
500 M min.
No flashover or insulation breakdown.
100 m ohms max.
* Including FPC conductor resistance
Contact resistance: 100 m max.
No damage, cracks, or parts dislocation.
No electrical discontinuity of 1 s or more.
Contact resistance: 100 m max.
No damage, cracks, or parts dislocation.
No electrical discontinuity of 1 s. min.
Contact resistance: 100 m max.
No damage, cracks, or parts dislocation.
Contact resistance: 100 m max.
Insulation resistance: 50 M min.
No damage, cracks, or parts dislocation.
Contact resistance: 100 m max.
Insulation resistance: 50 M min.
No damage, cracks, or parts dislocation.
No deformation of components affecting performance.
100 V DC
120 V AC /one minute
1 mA
20 cycles
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycle in
each of the 3 directions.
Acceleration of 981 m/s
2
, 6ms duration, sine half-wave
waveform, 3 cycles / each of 3 axis
96 hours at temperature of 40 and humidity of 90% to 95%.RH
Temperature: -55
/
+15
to +35
/
+85
/
+15
to +35
Time: 30
/
2 to 3
/
30
/
2 to 3 (Minutes)
5 cycles
Reflow: At the recommended temperature profile
Manual soldering: 3505 for 5 seconds
1. Insulation resistance
2. Withstanding voltage
3. Contact resistance
4. Durability
(insertion/ withdrawal)
5. Vibration
6. Shock
7. Humidity
(Steady state)
8. Temperature cycle
9. Resistance to
soldering heat
-
-
-
(05)
SH
0.4
54S
FH27
1
2
3
4
5
Series name: FH27
No. of contacts
Number of contacts: 10, 40, 54, 57, 60
Contact pitch: 0.4 mm
Terminal type
SH: SMT horizontal mounting type
Plating code
(05): Gold plated
(51): Tin-lead plated
1
4
5
2
3
3
B
Operation and Precautions
Operation
Precautions
1) Lift up the actuator. Use thumb or index finger.
1.FPC insertion procedure. Connector installed on
the board.
1
Do not apply excessive force or use any type of tool to operate the
actuator.
1
Lift up the actuator.
Carefully withdraw the FPC.
2.FPC removal
1
3
Rotate down the actuator until firmly closed. It is critical that the
inserted FPC is not moved and remains fully inserted.
2
The connector will assure reliable performance when the actuator is
open to 130maximum. Do not exceed this angle, as this may cause
permanent damage to the connector.
3
Exercise caution when applying upward force to the connected FPC.
Fully insert the FPC in the connector parallel to mounting surface, with
the exposed conductive traces facing down.
2
FPC conductor
surface
(Bottom side)
Over 130
4
Notes
The coplanarity of each terminal lead is within 0.1.
The contact terminal lead position indicates the dimension from the K surface, the bottom surface of the insulator body.
Slight variations in color of the plastic compounds do not affect form, fit or function of the connector.
Some versions may have material removed from this area. No affect on form, fit or function of the connector.
1
2
4
3
s
Connector Dimension
Unit: mm
Tape and reel packaging (2,500 pieces/reel).
Order by number of reels.
Part Number
FH27-10S-0.4SH
FH27-40S-0.4SH
FH27-54S-0.4SH
FH27-57S-0.4SH
FH27-60S-0.4SH
CL580-0004-0
CL580-0005-3
CL580-0001-2
CL580-0003-8
CL580-0006-6
10
40
54
57
60
0
6.6
18.6
24.2
25.4
26.6
0
3.6
15.6
21.2
22.4
23.6
0
5.24
17.24
22.84
24.04
25.24
0
6.0
18.0
23.6
24.8
26.0
CL No.
Number of Contacts
A
B
C
D
(0.15)
(C: FPC insertion slot dimension)
Polarizing mark indicator
D
Number of contacts indicator
0.4
0.15
Number of contacts
H
(0.15)
B
A
A**
H
0.5
(3.9)
(2.2)
(1.7)
3
0.15MAX
1
K
1.2
3.5
0
0
2
1
2
0.15MAX
4
5
B
Recommended PCB mounting pattern and metal mask dimensions
B
Recommended FPC Dimensions
Polyamide and thermally hardening adhesive is recommended as the materials for the stiffener.
Overlap between covering film layer and stiffener is 0.5mm min.
1
2
Unit: mm
Tape and tape reel packaging (2,500 pieces/reel).
Order by number of reels.
Part Number
FH27-10S-0.4SH
FH27-40S-0.4SH
FH27-54S-0.4SH
FH27-57S-0.4SH
FH27-60S-0.4SH
CL580-0004-0
CL580-0005-3
CL580-0001-2
CL580-0003-8
CL580-0006-6
10
40
54
57
60
0
3.6
15.6
21.2
22.4
23.6
0
5.5
17.5
23.1
24.3
25.5
0
5.2
17.2
22.8
24.0
25.2
0
4.01
16.01
21.61
22.81
24.01
CL No.
Number of Contacts
E
F
G
H
(0.175)
(0.25)
(3.5)
(0.25)
(0.2)
(0.5)
(0.2)
(0.225)
Outline of the connector
0.4
0.04 R
E
0.550.05
0.230.03(Land)
0.20.01(Metal mask)
1.40.05
2.250.05
0.80.05
0.550.05
F0.05
Recommended metal mask thickness: .t=0.12
R
G0.05
0.80.07
0.20.03
0.5MIN
3.2MIN(Stiffener)
0.20.05
1.20.05
1.90.1
R0.2
2.7MIN
2.2
E0.03
H0.05
G0.05
0.40.03
0.80.07
2-R0.2
R0.2MAX
2-R0.25MAX
(0.07)
(0.07)
0.270.03
0.130.03
Covering film layer
2
6
B
Packaging Specification
Unit: mm
2,500 pieces per reel.
q
Embossed Carrier Tape Dimensions
40.11
20.1
1.750.1
1.750.1
N0.1
L0.3
20.15
(P)
M0.1
N0.1
L0.3
(P)
(4.2)
(5.2)
(4.2)
(5.2)
(2)
(0.3)
(2)
(0.3)
1.5
+0.10
40.1
Unreeling direction
Unreeling direction
120.1
20.15
1.5
+0.10
1.7
+0.1
0
1.5
+0.1
0
(2)
(Q)
13
(380)
(80)
End portion
No connector inserted
(10 pockets min.)
No connector inserted
(10 pockets min.)
Embossed carrier tape
Top cover tape
Mounting portion
Lead portion (400mm min.)
q
Tape width up to 24mm .
q
Tape width 32mm and over.
q
Reel Dimensions
Part Number
FH27-10S-0.4SH
FH27-40S-0.4SH
FH27-54S-0.4SH
FH27-57S-0.4SH
FH27-60S-0.4SH
CL580-0004-0
CL580-0005-3
CL580-0001-2
CL580-0003-8
CL580-0006-6
10
40
54
57
60
16.0
32.0
44.0
44.0
44.0
-------
28.4
40.4
40.4
40.4
0
7.5
14.2
20.2
20.2
20.2
0
6.9
18.9
24.5
25.7
26.9
16.5
32.5
44.5
44.5
44.5
CL No.
Number of Contacts
L
M
N
P
Q
7
B
Recommended Temperature Profile
HRS test conditions
Solder method
:Reflow, IR/hot air
(Nihon Den-netsu Co., Ltd.'s Part
SENSBY NR-2)
Environment
:Room air
Solder composition :Paste, 63%Sn/37%Pb
(Senju Metal Industry, Co., Ltd.'s Part Number:
OZ63-201C-50-9)
Test board
:Glass epoxy 40mm100mm1.6mm thick
Land dimensions:0.23mm0.8mm
Metal mask
:0.20.80.12mm thick
The temperature profiles are based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume/thickness and board
size/thickness. Consult your solder paste and equipment
manufacturer for specific recommendations.
q
Using Typical Solder Paste
HRS test condition
Solder method
:Reflow, IR/hot air
(Nihon Den-netsu Co., Ltd.'s Part Number:
SENSBY NR-2)
Environment
:Room air
Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s Part Number:
M705-221CM5-42-10.5)
Test board
:Glass epoxy 70mm80mm1.6mm thick
Land dimensions:0.23mm08mm
Metal mask
:0.20.80.12mm thick
The temperature profiles shown are based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume / thickness and board size
/ thickness. Consult your solder paste and equipment manufacturer
for specific recommendations.
q
Using Lead-free Solder Paste
Start
Temperature()
Time (Seconds)
25
(60sec.)
(20 sec. to 30 sec.)
(30 sec.)
90 sec. to 120 sec.
Preheating
Soldering
0
50
100
150
150
160
240
200
5 sec. max.
200
250
MAX 250
Start
Time (Seconds)
25
(60sec.)
(60 sec.)
90 sec. to 120 sec.
0
50
100
150
150
200
230
200
250
Temperature()
Preheating
Soldering
8
B
FPC Construction (Recommended Specifications)
1. Using Single-sided FPC
Material Name
Covering layer film
Cover adhesive
Surface treatment
Copper foil
Base adhesive
Base film
Reinforcement material adhesive
Stiffener
Polyamide 1 mil thick.
Tin-lead plated
Cu
1/2oz
Polyamide 1 mil thick
Thermosetting adhesive
Polyamide 3 mil thick
Total
25
25
5
35
25
25
30
75
195
Material
Thickness (m)
2. Using Double-sided FPC
Material Name
Covering layer film
Cover adhesive
Surface treatment
Through-hole copper
Copper foil
Base adhesive
Base film
Base adhesive
Copper foil
Cover adhesive
Covering layer film
Reinforcement material adhesive
Stiffener
Polyamide 1 mil thick
Tin-lead plated
Cu
Cu
1/2oz
Polyamide 1 mil thick
Cu
1/2oz
Polyamide 1 mil thick
Thermosetting adhesive
Polyamide 1 mil thick
Total
25
25
5
15
18
18
25
18
18
25
25
25
25
199
Material
Thickness (m)
To prevent release of the lock due to FPC bending, use of the FPC with copper foil on bottom side is not recommended.
Bottom side
Bottom side
Top side
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
http://www.hirose.com
http://www.hirose-connectors.com
Top side