ChipFind - документация

Электронный компонент: HA17904AFP

Скачать:  PDF   ZIP
HA17904 Series
Dual Operational Amplifier
ADE-204-046 (Z)
Rev. 0
Dec. 2000
Description
HA17904 is dual operational amplifier which, provide internal phase compensation and high gain, and
mono power source operation is possible. It can be widely applied to control equipment and to general use.
Features
Wide range of operating supply voltage and mono power source operation is possible.
Wide range of common mode input voltage possible to operate with an input around 0V, and output
around 0V is available.
Frequency characteristics and input bias currrent are temperature compensated.
Ordering Information
Type No.
Application
Package
HA17904PSJ
Car use
DP-8
HA17904FPJ
Car use
FP-8D
HA17904FPK
Car use
HA17904PS
Industrial use
DP-8
HA17904FP
Industrial use
FP-8D
HA17904 Series
2
Pin Arrangement
+
Vout1
Vin()1
Vin(+)1
GND
V
CC
Vout2
Vin()2
Vin(+)2
+
8
7
6
5
1
2
3
4
(Top View)
1
2
Circuit Schematic (1/2)
Q
1
Q
4
Q
2
Q
3
Q
5
Q
6
Q
7
Q
13
Q
12
Q
11
Q
10
Q
8
Q
9
Vout
R
1
Vin(+)
Vin()
C
HA17904 Series
3
Absolute Maximum Ratings (Ta = 25C)
Ratings
Item
Symbol
HA17904PS
HA17904FP
HA17904PSJ
HA17904FPJ
HA17904FPK
Unit
Supply voltage
V
CC
32
32
32
32
32
V
Output sink
current
I
O sink
50
50
50
50
50
mA
Common-mode
input voltage
V
CM
0.3 to V
CC
0.3 to V
CC
0.3 to V
CC
0.3 to V
CC
0.3 to V
CC
V
Common-mode
differential
voltage
V
IN(diff)
V
CC
V
CC
V
CC
V
CC
V
CC
V
Power dissipation
P
T
570*
1
385*
2
570*
1
385*
2
385*
2
mW
Operating
temperature
range
Topr
20 to +75
20 to +75
40 to +85
40 to +85
40 to +125
C
Storage
temperature
range
Tstg
55 to +125
55 to +125
55 to +125
55 to +125
55 to +150
C
Notes: 1. These are the allowable values up to Ta = 55
C. Derate by 8.3mW/
C above that temperature.
2. These are the allowable values up to Ta = 45
C mounting on 30% wiring density glass epoxy
board. Derate by 7.14mW/
C above that temeperature.
HA17904 Series
4
Electrical Characteristics
1
(V
CC
= +15V, Ta = 25C)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Input offset voltage
V
IO
--
3
7
mV
V
CM
= 7.5V, R
S
= 50
, Rf = 50k
Input offset current
I
IO
--
5
50
nA
V
CM
= 7.5V, I
IO
=
|
I
I (+)
I
I ()
|
Input bias current
I
IB
--
30
250
nA
V
CM
= 7.5V
Power source rejection
ratio
PSRR
--
93
--
dB
R
S
= 1k
, Rf = 100k
Voltage gain
A
VD
75
90
--
dB
R
L
=
, R
S
= 1k
, Rf = 100k
Common mode rejection
ratio
CMR
--
80
--
dB
R
S
= 50
, Rf = 5k
Common mode input
voltage range
V
CM (+)
13.5
--
--
V
R
S
= 1k
, Rf = 100k
V
CM ()
--
--
0.3
V
R
S
= 1k
, Rf = 100k
Peak-to-peak output
voltage
Vop-p
--
13.6
--
V
f = 100Hz, R
L
= 20k
, R
S
= 1k
,
Rf = 100k
Output source current
Iosource
20
40
--
mA
V
IN
+
= 1V, V
IN
= 0V, V
OH
= 10V
Output sink current
Iosink
10
20
--
mA
V
IN
= 1V, V
IN
+
= 0V, V
OL
= 2.5V
Output sink current
Iosink
15
50
--
A
V
IN
= 1V, V
IN
+
= 0V,
Vout = 200mV
Supply current
I
CC
--
0.8
2
mA
V
IN
= GND, R
L
=
Slew rate
SR
--
0.2
--
V/
s
R
L
=
, V
CM
= 7.5V, f = 1.5kHz
Channel separation
CS
--
120
--
dB
f = 1kHz
Electrical Characteristics
2
(V
CC
= +15V, Ta =40 to +125C)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Input offset voltage
V
IO
--
--
7
mV
V
CM
= 7.5V, R
S
= 50
, R
L
= 50k
Input offset current
I
IO
--
--
200
nA
V
CM
= 7.5V, I
IO
=
|
I
I (+)
I
I ()
|
Input bias current
I
IB
--
--
500
nA
V
CM
= 7.5V
Common mode input
voltage range
V
CM
0
--
13.0
V
R
S
= 1k
, Rf = 100k
Supply current
I
CC
--
--
4
mA
V
IN
= GND, R
L
=
Note:
As for the characteristic curve, refer to HA17904FPK.
HA17904 Series
5
Characteristic Curves
10
20
30
100
75
50
25
0
Input Bias Current I
IB
(nA)
Power-Supply Voltage V
CC
(V)
Input Bias Current vs.
Power-Supply
Voltage Characteristics
55 35
125
90
80
70
60
50
40
30
20
10
0
Input Bias Current I
IB
(nA)
Ambient Temperature Ta (
C)
Input Bias Current vs.
Ambient
Temperature Characteristics
15
5
25
45
65
85 105
Ta = 25
C
Vin = 7.5 V
55
15
85
125
90
80
70
60
50
40
30
20
10
0
Output Sink Current I
o sink
(mA)
Ambient Temperature Ta (
C)
Output Sink Current vs.
Ambient Temperature Characteristics
35
5
25
45
65
105
55
15
85
125
90
80
70
60
50
40
30
20
10
0
Output Sink Current I
o source
(mA)
Ambient Temperature Ta (
C)
Output Source Current vs.
Ambient Temperature Characteristics
35
5
25
45
65
105
V
CC
= 15 V
V
OH
= 1 V
V
CC
= 15 V
V
OH
= 10 V
HA17904 Series
6
1
10
1 M
160
140
120
100
80
60
40
20
0
Voltage Gain A
VD
(dB)
Frequency f (Hz)
Voltage Gain vs.
Frequency Characteristics
100
1 k
10 k
100 k
30
160
140
120
100
80
60
40
20
0
Voltage Gain A
VD
(dB)
Power-Supply Voltage V
CC
(V)
Voltage Gain vs.
Power-Supply Voltage Characteristics
10
20
V
CC
= 15 V
Ta = 25
C
Ta = 25
C
30
4
3
2
1
0
Supply Current I
CC
(mA)
Power-Supply Voltage V
CC
(V)
Supply Current vs.
Power-Supply Voltage Characteristics
10
20
20
15
10
5
0
Maximum Output Voltage Amplitude
V
OP-P
(V
P-P
)
1 M
Frequency f (Hz)
10 k
100 k
Maximum Output Voltage Amplitude vs.
Frequency Characteristics
Ta = 25
C
Vin = GND
1 k
HA17904 Series
7
30
0.8
0.6
0.4
0.2
Slew Rate SR (V/
s)
Power-Supply Voltage V
CC
(V)
Slew Rate vs.
Power-Supply Voltage Characteristics
10
20
120
100
80
60
40
20
0
Common-Mode Rejection Ratio
CMR (dB)
Common-Mode Rejection Ratio vs.
Frequency Characteristics
1 M
Frequency f (Hz)
1 k
10 k
0
100
100 k
V1 = V2 = 1/2 V
CC
f = 1.5 kHz
V
CC
= 15 V
Ta = 25
C
R
S
= 50
HA17904 Series
8
Package Dimensions
Hitachi Code
JEDEC
EIAJ
Mass (reference value)
DP-8
Conforms
Conforms
0.54 g
Unit: mm
1
4
5
8
9.6
10.6 Max
0.89
1.3
6.3
7.4 Max
2.54 Min
5.06 Max
2.54
0.25
0.48
0.10
7.62
0.25
+ 0.10
0.05
0
15
0.1 Min
1.27 Max
Hitachi Code
JEDEC
EIAJ
Mass (reference value)
FP-8D
--
Conforms
0.10 g
Unit: mm
*Dimension including the plating thickness
Base material dimension
0.10
0.10
2.03 Max
4.4
*0.22
0.05
4.85
0.75 Max
0.40
0.06
0.60
+ 0.25
0.18
*0.42
0.08
0.12
0.15
0
8
M
8
5
1
4
1.05
5.25 Max
1.27
0.20
0.04
6.50
+ 0.25
0.15
HA17904 Series
9
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi's or any third party's patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party's rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi's sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-
safes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi's sales office for any questions regarding this document or Hitachi semiconductor
products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
Copyright
Hitachi, Ltd., 2000. All rights reserved. Printed in Japan.
Hitachi Asia Ltd.
Hitachi Tower
16 Collyer Quay #20-00,
Singapore 049318
Tel : <65>-538-6533/538-8577
Fax : <65>-538-6933/538-3877
URL : http://www.hitachi.com.sg
URL
NorthAmerica
: http://semiconductor.hitachi.com/
Europe
: http://www.hitachi-eu.com/hel/ecg
Asia
: http://sicapac.hitachi-asia.com
Japan
: http://www.hitachi.co.jp/Sicd/indx.htm
Hitachi Asia Ltd.
(Taipei Branch Office)
4/F, No. 167, Tun Hwa North Road,
Hung-Kuo Building,
Taipei (105), Taiwan
Tel : <886>-(2)-2718-3666
Fax : <886>-(2)-2718-8180
Telex : 23222 HAS-TP
URL : http://www.hitachi.com.tw
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower,
World Finance Centre,
Harbour City, Canton Road
Tsim Sha Tsui, Kowloon,
Hong Kong
Tel : <852>-(2)-735-9218
Fax : <852>-(2)-730-0281
URL : http://www.hitachi.com.hk
Hitachi Europe Ltd.
Electronic Components Group.
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 585160
Hitachi Europe GmbH
Electronic Components Group
Dornacher Stra
e 3
D-85622 Feldkirchen, Munich
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive,
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
For further information write to:
Colophon 2.0