HD74ALVC162244
16-bit Buffer / Driver with 3-state Outputs
ADE-205-204 (Z)
Preliminary
1st. Edition
January 1998
Description
The HD74ALVC162244 is designed specifically to improve both the performance and density of 3-state
memory address drivers, clock drivers, and bus oriented receivers and transmitters. The device can be used
as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. It provides true outputs and symmetrical
OE
(active-low output-enable) inputs.
To ensure the high impedance state during power up or power down,
OE should be tied to V
CC
through a
pullup resistor; the minimum value of the resistor is determined by the current sinking capability of the
driver.
All outputs, which are designed to sink up to 12 mA, include equivalent 26
resistors to reduce overshoot
and undreshoot.
Features
V
CC
= 2.3 V to 3.6 V
Typical V
OL
ground bounce < 0.8 V (@V
CC
= 3.3 V, Ta = 25C)
Typical V
OH
undershoot > 2.0 V (@V
CC
= 3.3 V, Ta = 25C)
High output current 12 mA (@V
CC
= 3.0 V)
All outputs have equivalent 26
series resistors, so no external resistors are required
HD74ALVC162244
4
Absolute Maximum Ratings
Item
Symbol
Ratings
Unit
Conditions
Supply voltage
V
CC
0.5 to 4.6
V
Input voltage
*1
V
I
0.5 to 4.6
V
Output voltage
*1, 2
V
O
0.5 to V
CC
+0.5
V
Input clamp current
I
IK
50
mA
V
I
< 0
Output clamp current
I
OK
50
mA
V
O
< 0 or V
O
> V
CC
Continuous output current
I
O
50
mA
V
O
= 0 to V
CC
V
CC
, GND current / pin
I
CC
or I
GND
100
mA
Maximum power dissipation
at Ta = 55
C (in still air)
*3
P
T
0.85
W
TSSOP
Storage temperature
T
stg
65 to 150
C
Notes:
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage
to the device. These are stress ratings only, and functional operation of the device at these or
any other conditions beyond those indicated under "recommended operating conditions" is not
implied. Exposure to absolute maximum rated conditions for extended periods may affect device
reliability.
1. The input and output negative voltage ratings may be exceeded if the input and output clamp
current ratings are observed.
2. This value is limited to 4.6 V maximum.
3. The maximum package power dissipation is calculated using a junction temperature of 150
C
and a board trace length of 750 mils.
Recommended Operating Conditions
Item
Symbol
Min
Max
Unit
Conditions
Supply voltage
V
CC
2.3
3.6
V
Input voltage
V
I
0
V
CC
V
Output voltage
V
O
0
V
CC
V
High level output current
I
OH
--
6
mA
V
CC
= 2.3 V
--
8
V
CC
= 2.7 V
--
12
V
CC
= 3.0 V
Low level output current
I
OL
--
6
mA
V
CC
= 2.3 V
--
8
V
CC
= 2.7 V
--
12
V
CC
= 3.0 V
Input transition rise or fall rate
t /
v
0
10
ns / V
Operating temperature
T
a
40
85
C
Note:
Unused control inputs must be held high or low to prevent them from floating.
PDF 
ZIP
