Features

Accurate measurement of avail-

able capacity in Lithium Ion bat-
teries

Provides a low-cost battery man-

agement solution for pack
integration

Complete circuit can fit in as
little as

square inch of PCB

Low operating current (120

礎

typical)

Less than 100nA of data
retention current

High-speed (5kb) single-wire

communication interface (HDQ
bus) for critical battery
parameters

Monitors and controls charge FET

in Li-Ion pack protection circuit

Direct drive of remaining capacity

LEDs

Measurements automatically

compensated for rate and
temperature

16-pin narrow SOIC

General Description

The bq2050H Lithium Ion Power
GaugeTM IC is intended for battery-
pack or in-system installation to
maintain an accurate record of
available battery capacity. The IC
monitors a voltage drop across a
sense resistor connected in series
between the negative battery termi-
n a l a n d g r o u n d t o d e t e r m i n e
charge and discharge activity of
the battery. Compensations for bat-
tery temperature, self discharge,
and rate of discharge are applied to
the charge counter to provide avail-
able capacity information across a
wide range of operating conditions.
Battery capacity is automatically re-
calibrated, or "learned," in the
course of a discharge cycle from full
to empty.

Nominal available capacity may be
directly indicated using a five-
segment LED display. These seg-

ments are used to graphically indi-
c a t e

a v a i l a b l e

c a p a c i t y .

T h e

bq2050H also supports a simple
single-line bidirectional serial link
to an external processor (common
ground). The 5kb HDQ bus interface
reduces communications overhead
in the external microcontroller.

Internal registers include available
capacity, temperature, scaled avail-
able energy, battery ID, battery
status, and Li-Ion charge FET
status. The external processor may
also overwrite some of the bq2050H
power gauge data registers.

The bq2050H can operate from the
batteries in the pack. The REF out-
put and an external transistor allow
a simple, inexpensive voltage regu-
lator to supply power to the circuit
from the cells.

bq2050H

LCOM

LED common output

SEG

/PROG

LED segment 1/

program 1 input

SEG

/PROG

LED segment 2/

program 2 input

SEG

/PROG

LED segment 3/

program 3 input

SEG

/PROG

LED segment 4/

program 4 input

SEG

/PROG

LED segment 5/

program 5 input

CFC

Charge FET control

output

PN2050H1.eps

16-Pin Narrow SOIC

VCC

REF

PSTAT

HDQ

RBI

DISP

LCOM

SEG1/PROG1

SEG2/PROG2

SEG3/PROG3

SEG4/PROG4

SEG5/PROG5

CFC

VSS

System ground

Sense resistor input

DISP

Display control input

Battery sense input

RBI

HDQ

Serial communications

input/output

PSTAT

Protector status input

REF

Voltage reference output

Supply voltage

Pin Connections

SLUS150璏AY 1999 D

Low-Cost Lithium Ion Power GaugeTM IC

Pin Names

Pin Descriptions

LCOM

LED common output

This open-drain output switches V

source current for the LEDs. The switch is
off during initialization to allow reading of
the soft pull-up or pull-down program resis-
tors. LCOM is also high impedance when the
display is off.

SEG

�

SEG

LED display segment outputs (dual func-
tion with PROG

璓ROG

)

Each output may activate an LED to sink
the current sourced from LCOM.

PROG

�

PROG

Programmed full count selection inputs
(dual function with SEG

璖EG

)

These three-level input pins define the pro-
grammed full count (PFC) thresholds de-
scribed in Table 2.

PROG

�

PROG

Power gauge scale selection inputs (dual
function with SEG

璖EG

)

These three-level input pins define the scale
factor described in Table 2.

PROG

Self-discharge rate selection (dual func-
tion with SEG

)

This three-level input pin defines

the

self-discharge and battery compensation fac-
tors as shown in Table 1.

CFC

Charge FET control output

This pin can be used as an additional control
to the charge FET of the Li-Ion pack protec-
tion circuitry.

Ground

Sense resistor input

The voltage drop (V

) across the sense re-

sistor R

is monitored and integrated over

time to interpret charge and discharge activ-
ity. The SR input is tied between the nega-
tive terminal of the battery and the sense re-
sistor. V

< V

indicates discharge, and

> V

indicates charge.

The effective

voltage drop, V

SRO

, as seen by the bq2050H

is V

+ V

DISP

Display control input

DISP high disables the LED display. DISP
tied to V

allows PROG

to connect di-

rectly to V

or V

instead of through a

pull-up or pull-down resistor. DISP floating
allows the LED display to be active during
charge. DISP low activates the display. See
Table 1.

Secondary battery input

This input monitors the battery cell voltage
potential through a high-impedance resis-
tive divider network for end-of-discharge
voltage (EDV) thresholds and battery-removed
detection.

RBI

Register backup input

This pin is used to provide backup potential to
the bq2050H registers during periods when
V

3V. A storage capacitor or a battery

can be connected to RBI.

HDQ

Serial communication input/output

This is the open-drain bidirectional commu-
nications port.

PSTAT

Protector status input

This input provides overvoltage status from
the Li-Ion protector circuit. It should con-
nect to V

when not used.

REF

Voltage reference output for regulator

REF provides a voltage reference output for
an optional micro-regulator.

Supply voltage input

bq2050H

Functional Description

General Operation

The bq2050H determines battery capacity by moni-
toring the amount of current input to or removed
from a rechargeable battery.

The bq2050H meas-

ures discharge and charge currents, measures bat-
tery voltage, estimates self-discharge, monitors the
battery for low battery-voltage thresholds, and com-
pensates for temperature and discharge rate. Cur-
rent measurement is measured by monitoring the
voltage across a small-value series sense resistor be-
tween the negative battery terminal and ground.
Scaled available energy is estimated using the re-
maining average battery voltage during the dis-
charge cycle and the remaining nominal available

capacity. The scaled available energy measurement
is corrected for environmental and operating condi-
tions.

Figure 1 shows a typical battery pack application of the
bq2050H using the LED display capability as a charge-
state indicator. The bq2050H is configured to display
capacity in relative display mode. The relative display
mode uses the last measured discharge capacity of the
battery as the battery "full" reference. A push-button
display feature is available for momentarily enabling
the LED display.

The bq2050H monitors the charge and discharge cur-
rents as a voltage across a sense resistor. (See R

in Fig-

ure 1.) A filter between the negative battery terminal
and the SR pin is required.

bq2050H

FG2050H1.eps

CFC

SEG5/PROG5

SEG4/PROG4

SEG3/PROG3

SEG2/PROG2

SEG1/PROG1

DISP

VCC

REF

bq2050H

Power Gauge IC

LCOM

VSS

RBI

HDQ

VCC

Q1
ZVNL110A

RB1

RB2

See note 4

Load

Charger

1. Indicates optional.

2. Programming resistors and ESD-protection diodes are not shown.

3. RC on SR is required.

4. A series diode is required on RBI if the bottom series cell is used as the backup source.
If the cell is used, the backup capacitor is not required, and the anode is connected to the
positive terminal of the cell.

100K

PSTAT

Notes:

0.1

礔

Figure 1. Battery Pack Application Diagram--LED Display

Voltage Thresholds

In conjunction with monitoring V

for charge/discharge

currents, the bq2050H monitors the battery potential
through the SB pin. The voltage is determined through
a resistor-divider network per the following equation:

RB1

RB2

- 1

where N is the number of cells, RB1 is connected to the
positive battery terminal, and RB2 is connected to the
negative battery terminal. The single-cell battery volt-
age is monitored for the end-of-discharge voltage (EDV)
thresholds. The EDV threshold levels are used to deter-
mine when the battery has reached an "empty" state.

The EDV thresholds for the bq2050H are programmable
with the default values fixed at:

EDV1 (first) = 0.76V

EDVF (final) = EDV1-0.025V = 0.735V

If V

is below either of the two EDV thresholds, the as-

sociated flag is latched and remains latched, independ-
ent of V

, until the next valid charge. The V

value is

also available over the serial port.

During discharge and charge, the bq2050H monitors
V

for various thresholds used to compensate the

charge counter. EDV monitoring is disabled if the dis-
charge rate is greater than 2C (OVLD Flag = 1) and re-
sumes

second after the rate falls below 2C.

RBI Input

The RBI input pin is intended to be used with a storage
capacitor or external supply to provide backup potential
to the internal bq2050H registers when V

drops below

3.0V. V

is output on RBI when V

is above 3.0V. If us-

ing an external supply (such as the bottom series cell) as
the backup source, an external diode is required for isola-
tion.

Reset

The bq2050H can be reset by removing V

and ground-

ing the RBI pin for 15 seconds or by commands over the
serial port. The serial port reset command sequence re-
quires writing 00h to register PPFC (address = 1Eh) and
then writing 00h to register LMD (address = 05h).

Temperature

The bq2050H internally determines the temperature in
10癈 steps centered from approximately -35癈 to +85癈.
The temperature steps are used to adapt charge and dis-
charge rate compensations, self-discharge counting, and
available charge display translation. The temperature
range is available over the serial port in 10癈 incre-
ments as shown in the following table:

Layout Considerations

The bq2050H measures the voltage differential between
the SR and V

pins. V

(the offset voltage at the SR

pin) is greatly affected by PC board layout. For optimal
results, the PC board layout should follow the strict rule
of a single-point ground return. Sharing high-current
ground with small signal ground causes undesirable
noise on the small signal nodes. Additionally:

The capacitors (C1 and C2) should be placed as
close

possible

the

and

pins,

respectively, and their paths to V

should be as

short as possible. A high-quality ceramic capacitor
of 0.1

礔 is recommended for V

The sense-resistor capacitor should be placed as close
as possible to the SR pin.

The sense resistor (R

) should be as close as possible to

the bq2050H.

bq2050H

TMP (hex)

Temperature Range

< -30癈

-30癈 to -20癈

-20癈 to -10癈

-10癈 to 0癈

0癈 to 10癈

10癈 to 20癈

20癈 to 30癈

30癈 to 40癈

40癈 to 50癈

50癈 to 60癈

60癈 to 70癈

70癈 to 80癈

> 80癈

Gas Gauge Operation

The operational overview diagram in Figure 2 illustrates
the operation of the bq2050H. The bq2050H accumu-
lates a measure of charge and discharge currents, as
well as an estimation of self-discharge.

The accumu-

lated charge and discharge currents are adjusted for
temperature and rate to provide the indication of com-
pensated available capacity to the host system or user.

The main counter, Nominal Available Capacity (NAC),
represents the available battery capacity at any given
time.

Battery charging increments the NAC register,

while battery discharging and self-discharge decrement
the NAC register and increment the DCR (Discharge
Count Register).

The Discharge Count Register is used to update the Last
Measured Discharge (LMD) register only if a complete
battery discharge from full to empty occurs without any
partial battery charges. Therefore, the bq2050H adapts
its capacity determination based on the actual condi-
tions of discharge.

The battery's initial capacity equals the Programmed
Full Count (PFC) shown in Table 2. Until LMD is up-
dated, NAC counts up to but not beyond this threshold
during subsequent charges. This approach allows the
gas gauge to be charger-independent and compatible
with any type of charge regime.

Last Measured Discharge (LMD) or learned
battery capacity:

LMD is the last measured discharge capacity of the
battery. On initialization (application of V

or bat-

tery replacement), LMD = PFC. During subsequent
discharges, the LMD is updated with the latest
measured capacity in the Discharge Count Register
representing a discharge from full to below EDV1.
A qualified discharge is necessary for a capacity
transfer from the DCR to the LMD register.

The

LMD also serves as the 100% reference threshold
used by the relative display mode.

bq2050H

FG2050H2.eps

Temperature

Compensation

Charge
Current

Discharge

Current

Self-Discharge

Timer

Nominal

Available

Charge

(NAC)

Last

Measured

Discharged

(LMD)

Discharge

Count

(DCR)

Qualified

Transfer

Rate and

Temperature

Compensation

Temperature

Compensation

Temperature Step,
Other Data

Inputs

Main Counters

and Capacity

Reference (LMD)

Outputs

Serial

Port

Compensated

Available Charge
LED Display, etc.

Rate and

Temperature

Compensation

Figure 2. Operational Overview

Programmed Full Count (PFC) or initial bat-
tery capacity:

The initial LMD and gas gauge rate values are pro-
grammed by using PROG

璓ROG

. The bq2050H

is configured for a given application by selecting a
PFC value from Table 2. The correct PFC may be
determined by multiplying the rated battery capac-
ity in mAh by the sense resistor value:

Battery capacity (mAh) * sense resistor () =

PFC (mVh)

Selecting a PFC slightly less than the rated capac-
ity provides a conservative capacity reference until
the bq2050H "learns" a new capacity reference.

Example: Selecting a PFC Value

Given:

Sense resistor = 0.05

Number of cells = 2
Capacity = 1000mAh, Li-Ion battery, coke-anode
Current range = 50mA to 1A
Relative display mode
Self-discharge =

NAC

512

per day @ 25癈

Voltage drop over sense resistor = 2.5mV to 50mV
Nominal discharge voltage = 3.6V

Therefore:

1000mAh * 0.05 = 50mVh

bq2050H

PROG

Pro-

grammed

Full

Count

(PFC)

PROG

= L

PROG

= Z or H

Units

PROG

= H

PROG

= Z

PROG

= L PROG

= H PROG

= Z PROG

= L

SCALE =

1/80

SCALE =

1/160

SCALE =

1/320

SCALE =

1/640

SCALE =

1/1280

SCALE =

1/2560

mVh/
count

49152

614

307

154

76.8

38.4

19.2

mVh

45056

563

282

141

70.4

35.2

17.6

mVh

40960

512

256

128

64.0

32.0

16.0

mVh

36864

461

230

115

57.6

28.8

14.4

mVh

33792

422

211

106

53.0

26.4

13.2

mVh

30720

384

192

96.0

48.0

24.0

12.0

mVh

27648

346

173

86.4

43.2

21.6

10.8

mVh

25600

320

160

80.0

40.0

20.0

10.0

mVh

22528

282

141

70.4

35.2

17.6

8.8

mVh

equivalent to 2

counts/s (nom.)

22.5

11.25

5.6

2.8

Table 2. bq2050H Programmed Full Count mVh, V

Gain Selections

Pin

Connection

PROG

Compensation/Self-Discharge

(See Tables 3 and 4)

DISP

Display State

Coke anode/disabled

LEDs disabled

Coke anode/

NAC

512

LEDs on when charging

Graphite anode/

NAC

512

LEDs on for 4 s

Table 1. Self-Discharge and Capacity Compensation

Select:

PFC = 30720 counts or 48mVh
PROG

= float

PROG

= low

PROG

= high

PROG

= float

PROG

= float

The initial full battery capacity is 48mVh (960mAh)
until the bq2050H "learns" a new capacity with a
qualified discharge from full to EDV1.

Nominal Available Capacity (NAC):

NAC counts up during charge to a maximum value
of LMD and down during discharge and self-dis-
charge to 0. NAC is reset to 0 on initialization and
on the first valid charge following discharge to
EDV1. To prevent overstatement of charge during
periods of overcharge, NAC stops incrementing
when NAC = LMD.

Discharge Count Register (DCR):

The DCR counts up during discharge independent
of NAC and could continue increasing after NAC
has decremented to 0. Prior to NAC = 0 (empty
battery), both discharge and self-discharge in-
crement the DCR. After NAC = 0, only discharge
increments the DCR. The DCR resets to 0 when
NAC = LMD. The DCR does not roll over but stops
counting when it reaches FFh.

The DCR value becomes the new LMD value on the
first charge after a valid discharge to V

EDV1

if all

the following conditions are met:

No valid charge initiations (charges greater than
2 NAC updates where V

SRO

> V

SRQ

) occurred

during the period between NAC = LMD and EDV1.

The self-discharge is less than 6% of NAC.

The temperature is

0癈 when the EDV1 level

is reached during discharge.

VDQ is set

The valid discharge flag (VDQ) indicates whether
the present discharge is valid for LMD update. If
the DCR update value is less than 0.94

LMD, LMD

will only be modified by 0.94

LMD. This prevents

invalid DCR values from corrupting LMD.

Scaled Available Energy (SAE):

SAE is useful in determining the available energy
within the battery, and may provide a more useful
capacity reference in battery chemistries with
sloped voltage profiles during discharge. SAE may
be converted to an mWh value using the following
formula:

E(mWh) = (SAEH

SAEL)

256

1 2

SCALE

+ R

)

where R

, R

, and R

are resistor values in

ohms, as shown in Figure 1. SCALE is the selected
scale from Table 2.

6. Compensated Available Capacity (CACT)

CACT counts similarly to NAC, but contains the available
capacity compensated for discharge rate and temperature.

Charge Counting

Charge activity is detected based on a positive voltage
on the SR input.

If charge activity is detected, the

bq2050H increments NAC at a rate proportional to V

and, if enabled, activates an LED display.

The bq2050H counts charge activity when the voltage at
the SR input (V

SRO

) exceeds the minimum charge

threshold (V

SRQ

). A valid charge is detected when NAC

has been updated twice without discharging or reaching
the digital magnitude filter time-out.

Once a valid

charge is detected, charge counting continues until V

including offset, falls below V

SRQ

Discharge Counting

Discharge activity is detected based on a negative volt-
age on the SR input. All discharge counts where V

SRO

is less than the minimum discharge threshold (V

SRD

)

cause the NAC register to decrement and the DCR to
increment.

Self-Discharge Counting

The bq2050H continuously decrements NAC and incre-
ments DCR for self-discharge based on time and tempera-
ture.

Charge/Discharge Current

The bq2050H current-scale registers, VSRH and VSRL,
can be used to determine the battery charge or dis-
charge current. See the Current Scale Register descrip-
tion for details.

Count Compensations

Compensated Available Capacity

Compensated Available Capacity compensation is based
on the rate of discharge, temperature, and negative
electrode type. Tables 3A and 3B outline the correction
factor typically used for graphite-anode Li-Ion batteries,
and Tables 4A and 4B outline the factors typically used for
coke-anode Li-Ion batteries. The compensation factor is
applied to NAC to derive the CACD and CACT values.

bq2050H

The CACD value is the available charge compensated
for the rate of discharge. At high discharge rates, CACD
is reduced. The reduction is maintained until a valid
charge is detected.

The CACT value is the available

charge compensated for the rate of discharge and tem-
perature. The CACT value is used to drive the LED dis-
play.

Charge Compensation

The bq2050H also monitors temperature during charge.
If the temperature is <0

癈, NAC will only increment up

to 0.94 * LMD, inhibiting VDQ from being set.

This

keeps a "learn" cycle from occurring when the battery is
charged at very low temperatures. If the temperature
rises above 0

癈, NAC will be allowed to count up to NAC

= LMD.

Self-Discharge Compensation

The self-discharge compensation is programmed for a
nominal rate of

512

NAC per day. This is the rate that

NAC is reduced for a battery within the 20�30癈 tem-
perature range. This rate varies across 8 ranges from
<10癈 to >70癈, as shown in Table 5.

Self-discharge may be disabled by connecting PROG

= H.

Digital Magnitude Filter

The bq2050H has a digital filter to eliminate charge and
discharge counting below a set threshold. The minimum
charge (V

SRQ

) and discharge (V

SRD

) threshold for the

bq2050H is 250

礦.

Pack Protection Supervision

The bq2050H can monitor the charge FET in a Li-Ion
pack protector circuit as shown in Figure 3. If the bat-
tery voltage is too high or the temperature is out of the
0--60

癈 range, the bq2050H disables the charge FET

with the CFC output, which turns off the charge to the
pack.

The PSTAT input is used to monitor the protector state. If
PSTAT is above 2.5V, bit 5 of FLGS1 is set to 1. If PSTAT
is below 0.5V, bit 5 of FLGS1 is cleared to zero. Using this
input, the system can monitor the state of the charge con-

bq2050H

Temperature Range

Typical Rate

PROG

= Z or L

< 10癈

NAC

2048

10�20癈

NAC

1024

20�30癈

NAC

512

30�40癈

NAC

256

40�50癈

NAC

128

50�60癈

NAC

60�70癈

NAC

> 70癈

NAC

Table 5. Self-Discharge Compensation

Approximate Discharge

Rate

Available Capacity

Reduction

< 0.5C

0.5C

0.05

LMD

Table 3A. Graphite Anode

Temperature

Available Capacity

Reduction

10癈

0癈 to 10癈

0.05

LMD

-20癈 to 0癈

0.15

LMD

-20癈

0.37

LMD

Table 3B. Graphite Anode

Approximate Discharge

Rate

Available Capacity

Reduction

<0.5C

0.5C

0.10

LMD

Table 4A. Coke Anode

Temperature

Available Capacity

Reduction

10癈

0癈 to 10癈

0.10

LMD

-20癈 to 0癈

0.30

LMD

-20癈

0.60

LMD

Table 4B. Coke Anode

trol FET signal and can quickly determine if the protector
circuit is operating properly during charge.

> NMCV or the

battery temperature is < 0

癈 or > 60癈, then CFC is

driven low.

Error Summary

Capacity Inaccurate

The LMD is susceptible to error on initialization or if no
updates occur.

On initialization, the LMD value in-

cludes the error between the programmed full capacity
and the actual capacity. This error is present until a
valid discharge occurs and LMD is updated (see the
DCR description). The other cause of LMD error is bat-
tery wear-out. As the battery ages, the measured capac-
ity must be adjusted to account for changes in actual
battery capacity.

A Capacity Inaccurate counter (CPI) is maintained and
incremented each time a valid charge occurs (qualified
by NAC; see the CPI register description). It is reset
whenever LMD is updated from the DCR. The counter
does not wrap around but stops counting at 255. The ca-
pacity inaccurate flag (CI) is set if LMD has not been
updated following 64 valid charges.

Current-Sensing Error

Table 6 shows the non-linearity and non-repeatability
errors associated with the bq2050H current sensing.

Table 7 illustrates the current-sensing error as a func-
tion of V

. A digital filter prevents charge and dis-

charge counts to the NAC register when V

SRO

is be-

tween V

SRQ

and V

SRD

bq2050H

Symbol

Parameter

Typical

Maximum

Units

Notes

INL

Integrated non-linearity
error

� 2

� 4

Add 0.1% per 癈 above or below 25癈
and 1% per volt above or below 4.25V.

INR

Integrated non-
repeatability error

� 1

� 2

Measurement repeatability given
similar operating conditions.

Table 6. bq2050H Current-Sensing Errors

FG2050H3.eps

Charger

PSTAT

Charge

Control

Discharge

Control

CFC

RLOAD

VSS

bq2050H

Figure 3. bq2050H Pack Supervision

Communicating With the bq2050H

The bq2050H includes a simple single-pin (HDQ plus return)
serial data interface. A host processor uses the interface to
access various bq2050H registers.

Battery characteristics

may be easily monitored by adding a single contact to the
battery pack.

The open-drain HDQ pin on the bq2050H

should be pulled up by the host system, or may be left float-
ing if the serial interface is not used.

The interface uses a command-based protocol, where the
host processor sends a command byte to the bq2050H.
The command directs the bq2050H to either store the
next eight bits of data received to a register specified by
the command byte or output the eight bits of data speci-
fied by the command byte. (See Figure 4.)

The communication protocol is asynchronous return-to-
one. Command and data bytes consist of a stream of
eight bits that have a maximum transmission rate of
5K bits/sec. The least-significant bit of a command or
data byte is transmitted first.

The protocol is simple

enough that it can be implemented by most host proces-
sors using either polled or interrupt processing. Data in-
put from the bq2050H may be sampled using the pulse--
width capture timers available on some microcontrollers.

If a communication error occurs (e.g., t

CYCB

> 250

祍),

the bq2050H should be sent a BREAK to reinitiate the
serial interface. A BREAK is detected when the HDQ
pin is driven to a logic-low state for a time, t

or greater.

The HDQ pin should then be returned to its normal
ready-high logic state for a time, t

. The bq2050H is

now ready to receive a command from the host proces-
sor.

The return-to-one data bit frame consists of three dis-
tinct sections.

The first section is used to start the

transmission by either the host or the bq2050H taking
the HDQ pin to a logic-low state for a period, t

STRH;B

The next section is the actual data transmission, where
the data should be valid by a period, t

DSU;B

, after the

negative edge used to start communication. The data

should be held for a period, t

DH;DV

, to allow the host or

bq2050H to sample the data bit.

The final section is used to stop the transmission by re-
turning the HDQ pin to a logic-high state by at least a
period, t

SSU;B

, after the negative edge used to start com-

munication. The final logic-high state should be until a
period t

CYCH;B

, to allow time to ensure that the bit

transmission was stopped properly. The timings for data
and break communication are given in the serial com-
munication timing specification and illustration sec-
tions.

Communication with the bq2050H is always performed
with the least-significant bit being transmitted first. Fig-
ure 5 shows an example of a communication sequence to
read the bq2050H NACH register.

bq2050H Command Code and
Registers

The bq2050H status registers are listed in Table 8 and de-
scribed below. All registers are Read/Write in the bq2050H.
Caution: When writing to bq2050H registers ensure
that proper data is written. A write-verify read is rec-
ommended.

Command Code

The bq2050H latches the command code when eight
valid command bits have been received by the bq2050H.
The command code contains two fields:

W/R bit

Command address

The W/R bit of the command code is used to select whether
the received command is for a read or a write function.

The W/R values are:

Where W/R is:

The bq2050H outputs the requested register
contents specified by the address portion of com-
mand code.

The following eight bits should be written to the
register specified by the address portion of com-
mand code.

The lower seven-bit field of the command code contains
the address portion of the register to be accessed.

bq2050H

(

�V)

Sense Resistor

100

0.25

0.10

0.05

100

0.50

0.20

0.10

150

0.75

0.30

0.15

180

0.90

0.36

0.18

Table 7. V

-Related Current Sense Error

(Current = 1A)

Command Code Bits

W/R

bq2050H

Symbol

Register Name

Loc.

(hex)

Read/

Write

Control Field

7(MSB)

0(LSB)

FLGS1

Primary status flags
register

01h

CHGS

BRP

PSTAT

VDQ

EDV1

EDVF

TMP

Temperature register

02h

TMP3

TMP2

TMP1

TMP0

GG3

GG2

GG1

GG0

NACH

Nominal available capac-
ity high byte register

03h

R/W NACH7 NACH6 NACH5 NACH4 NACH3 NACH2 NACH1 NACH0

NACL

Nominal available
capacity low byte register

17h

R/W

NACL7 NACL6 NACL5 NACL4 NACL3 NACL2 NACL1 NACL0

BATID

Battery identification
register

04h

R/W BATID7 BATID6 BATID5 BATID4 BATID3 BATID2 BATID1 BATID0

LMD

Last measured
discharge register

05h

R/W

LMD7

LMD6

LMD5

LMD4

LMD3

LMD2

LMD1

LMD0

FLGS2

Secondary status flags
register

06h

RSVD

DR2

DR1

DR0

ENINT

RSVD

OVLD

PPD

Program pin pull-down
register

07h

RSVD

PPD5

PPD4

PPD3

PPD2

PPD1

PPU

Program pin pull-up
register

08h

RSVD

PPU5

PPU4

PPU3

PPU2

PPU1

CPI

Capacity
inaccurate count register

09h

R/W

CPI7

CPI6

CPI5

CPI4

CPI3

CPI2

CPI1

CPI0

VSB

Battery voltage
register

0bh

VSB7

VSB6

VSB5

VSB4

VSB3

VSB2

VSB1

VSB0

VTS

End-of-discharge thresh-
old select register

0ch

R/W

VTS7

VTS6

VTS5

VTS4

VTS3

VTS2

VTS1

VTS0

CACT

Temperature and Dis-
charge Rate compensated
available capacity

0dh

R/W

CACT7 CACT6 CACT5 CACT4 CACT3 CACT2 CACT1 CACT0

CACD

Discharge Rate com-
pensated available
capacity

0eh

R/W

CACD7 CACD6 CACD5 CACD4 CACD3 CACD2 CACD1 CACD0

SAEH

Scaled available energy
high byte register

0fh

SAEH7 SAEH6 SAEH5 SAEH4 SAEH3 SAEH2 SAEH1 SAEH0

SAEL

Scaled available energy
low byte register

10h

SAEL7 SAEL6 SAEL5 SAEL4 SAEL3 SAEL2 SAEL1 SAEL0

RCAC

Relative CAC

11h

RCAC6 RCAC5 RCAC4 RCAC3 RCAC2 RCAC1 RCAC0

VSRH

Current scale high

12h

VSRH7 VSRH6 VSRH5 VSRH4 VSRH3 VSRH2 VSRH1 VSRH0

VSRL

Current scale low

13h

VSRL7 VSRL6 VSRL5 VSRL4 VSRL3 VSRL2 VSRL1 VSRL0

NMCV

Maximum cell voltage

15h

R/W NMCV7 NMCV6 NMCV5 NMCV4 NMCV3 NMCV2 NMCV1 NMCV0

DCR

Discharge register

18h

R/W

DCR7

DCR6

DCR5

DCR4

DCR3

DCR2

DCR1

DCR0

PPFC

Program pin data

1eh

R/W

RSVD

INTSS

Interrupt

38h

RSVD

RSVD DCHGI RSVD

RSVD

CHGI

RST

Reset register

39h

R/W

RST

HEXFF Check register

3fh

R/W

Notes:

RSVD = reserved.
All other registers not documented are reserved.

Table 8. bq2050H Command and Status Registers

Primary Status Flags Register (FLGS1)

The FLGS1 register (address = 01h) contains the pri-
mary bq2050H flags.

The charge status flag (CHGS) is asserted when a
valid charge rate is detected.

Charge rate is deemed

valid when V

SRO

> V

SRQ

. A V

SRO

of less than V

SRQ

discharge activity clears CHGS.

The CHGS values are:

Where CHGS is:

Either discharge activity detected or V

SRO

SRQ

SRO

> V

SRQ

The battery replaced flag (BRP) is asserted whenever
the bq2050H is reset either by application of V

or by a

serial port command. BRP is reset when either a valid
charge action increments NAC to be equal to LMD, or a
valid charge action is detected after the EDV1 flag is as-
serted. BRP = 1 signifies that the device has been reset.

The BRP values are:

Where BRP is:

Battery is charged until NAC = LMD or dis-
charged until the EDV1 flag is asserted

bq2050H is reset

The protector status flag (PSTAT) provides information
on the state of the overvoltage protector within the Li-
Ion battery pack. The PSTAT flag is asserted whenever
this input is high and is cleared when the input is low.

The PSTAT values are:

Where PSTAT is:

PSTAT input is low (PSTAT < 0.5V)

PSTAT input is high (PSTAT > 2.5V)

The capacity inaccurate flag (CI) is used to warn the
user that the battery has been charged a substantial
number of times since LMD has been updated. The CI
flag is asserted on the 64th charge after the last LMD
update or when the bq2050H is reset. The flag is cleared
after an LMD update.

The CI values are:

Where CI is:

When LMD is updated with a valid full dis-
charge

After the 64th valid charge action with no
LMD updates or the bq2050H is reset

The valid discharge flag (VDQ) is asserted when the
bq2050H is discharged from NAC=LMD. The flag re-
mains set until either LMD is updated or one of three
actions that can clear VDQ occurs:

When NAC has been reduced by more than 6%
because of self-discharge since VDQ was set.

A valid charge action sustained at V

SRO

> V

SRQ

for

at least 2 NAC updates.

The EDV1 flag was set at a temperature below 0癈

The VDQ values are:

Where VDQ is:

Self-discharge of 6% of NAC, valid charge
action detected, EDV1 asserted with the
temperature less than 0癈, or reset

On first discharge after NAC = LMD

bq2050H

FLGS1 Bits

CHGS

FLGS1 Bits

BRP

FLGS1 Bits

PSTAT

Command Code Bits

AD6 AD5

AD4

AD3

AD2

AD1

AD0

(LSB)

FLGS1 Bits

VDQ

The first end-of-discharge warning flag (EDV1)
warns the user that the battery is almost empty. The
first segment pin, SEG

, is modulated at a 4Hz rate if

the display is enabled once EDV1 is asserted, which
should warn the user that loss of battery power is immi-
nent. The EDV1 flag is latched until a valid charge has
been detected. The EDV1 threshold is externally con-
trolled via the VTS register (see Voltage Threshold Reg-
ister).

The EDV1 values are:

Where EDV1 is:

Valid charge action detected, V

< V

providing that the discharge rate

is < 2C

The final end-of-discharge warning flag (EDVF) flag
is used to warn that battery power is at a failure condi-
tion. All segment drivers are turned off. The EDVF flag
is latched until a valid charge has been detected. The
EDVF threshold is set 25mV below the EDV1 threshold.

The EDVF values are:

Where EDVF is:

Valid charge action detected, V

- 25mV)

< (V

-25mV) providing the discharge

rate is < 2C

Temperature Register (TMP)

The TMP register (address=02h) contains the battery
temperature.

The bq2050H contains an internal temperature sensor.
The temperature is used to set charge and discharge ef-
ficiency factors as well as to adjust the self-discharge co-
efficient. The temperature register contents may be
translated as shown in Table 9.

The bq2050H calculates the gas gauge bits, GG3-GG0 as a
function of CACT and LMD. The results of the calculation
give available capacity in

increments from 0 to

Nominal Available Capacity Registers
(NACH/NACL)

The NACH high-byte register (address=03h) and the
NACL low-byte register (address=17h) are the main gas
gauging registers for the bq2050H. The NAC registers are
incremented during charge actions and decremented dur-
ing discharge and self-discharge actions.

NACH and

NACL are set to 0 during a bq2050H reset.

Writing to the NAC registers affects the available charge
counts and, therefore, affects the bq2050H gas gauge opera-
tion. Do not write the NAC registers to a value greater than
LMD.

Battery Identification Register (BATID)

The BATID register (address=04h) is available for use
by the system to determine the type of battery pack.
The BATID contents are retained as long as V

RBI

greater than 2V. The contents of BATID have no effect
on the operation of the bq2050H. There is no default
setting for this register.

bq2050H

TMP3

TMP2

TMP1

TMP0

Temperature

T < -30癈

-30癈 < T < -20癈

-20癈 < T < -10癈

-10癈 < T < 0癈

0癈 < T < 10癈

10癈 < T < 20癈

20癈 < T < 30癈

30癈 < T < 40癈

40癈 < T < 50癈

50癈 < T < 60癈

60癈 < T < 70癈

70癈 < T < 80癈

T > 80癈

Table 9. Temperature Register

TMP Gas Gauge Bits

GG3

GG2

GG1

GG0

FLGS1 Bits

EDV1

FLGS1 Bits

EDVF

TMP Temperature Bits

TMP3 TMP2 TMP1 TMP0

Last Measured Discharge Register (LMD)

LMD is the register (address=05h) that the bq2050H
uses as a measured full reference. The bq2050H adjusts
LMD based on the measured discharge capacity of the
battery from full to empty. In this way the bq2050H up-
dates the capacity of the battery. LMD is set to PFC
during a bq2050H reset.

LMD is set to DCR upon the first valid charge after EDV
is set if VDQ is set.

If DCR < 0.94 LMD, then LMD is set to 0.94

LMD.

Secondary Status Flags Register (FLGS2)

The FLGS2 register (address=06h) contains the secon-
dary bq2050H flags.

Bit 7 and bit 1 of FLGS2 are reserved. Do not write to
these bits.

The discharge rate flags, DR2�0, are bits 6�4.

They are used to determine the current discharge re-
gime as follows:

The enable interrupt flag (ENINT) is a test bit used to
determine V

activity sensed by the bq2050H.

The

state of this bit will vary and should be ignored by the
system.

The valid charge flag (VQ), bit 2 of FLGS2, is used to
indicate whether the bq2050H recognizes a valid charge
condition. This bit is reset on the first discharge after
NAC = LMD.

The VQ values are:

Where VQ is:

Valid charge action not detected between a
discharge from NAC = LMD and EDV1

Valid charge action detected

The overload flag (OVLD) is asserted when a discharge
rate in excess of 2C is detected. OVLD remains asserted
as long as the condition persists and is cleared 0.5 sec-
onds after the rate drops below 2C. The overload condi-
tion is used to stop sampling of the battery terminal char-
acteristics for end-of-discharge determination.

Program Pin Pull-Down Register (PPD)

The PPD register (address=07h) contains some of the pro-
gramming pin information for the bq2050H. The segment
drivers, SEG

1�5

, have a corresponding PPD register loca-

tion, PPD

1�5

. A given location is set if a pull-down resis-

tor has been detected on its corresponding segment driver.
For example, if SEG

and SEG

have pull-down resistors,

the contents of PPD are xxx01001.

Program Pin Pull-Up Register (PPU)

The PPU register (address=08h) contains the rest of the
programming pin information for the bq2050H. The seg-
ment drivers, SEG

1�5

, have a corresponding PPU register

location, PPU

1�5

. A given location is set if a pull-up resis-

tor has been detected on its corresponding segment driver.
For example, if SEG

and SEG

have pull-up resistors, the

contents of PPU are xxx10100.

Capacity Inaccurate Count Register (CPI)

The CPI register (address=09h) is used to indicate the
number of times a battery has been charged without an
LMD update. Because the capacity of a rechargeable
battery varies with age and operating conditions, the
bq2050H adapts to the changing capacity over time. A
complete discharge from full (NAC=LMD) to empty
(EDV1=1) is required to perform an LMD update assum-
ing there have been no intervening valid charges, the
temperature is greater than or equal to 0癈, and there
has been no more than a 6% self-discharge reduction.

bq2050H

PPD/PPU Bits

RSVD RSVD RSVD PPU

PPU

RSVD RSVD RSVD PPD

PPD

FLGS2 Bits

OVLD

FLGS2 Bits

DR2

DR1

DR0

DR2

DR1

DR0

Discharge Rate

DRATE

< 0.5C

0.5C

DRATE < 2C

2C < DRATE

FLGS2 Bits

ENINT

FLGS2 Bits

The CPI register is incremented every time a valid
charge is detected. When NAC > 0.94 * LMD, however,

the CPI register increments on the first valid charge;
CPI does not increment again for a valid charge until
NAC < 0.94 * LMD. This prevents continuous trickle

charging from incrementing CPI if self-discharge decre-
ments NAC. The CPI register increments to 255 with-
out rolling over. When the contents of CPI are incre-
mented to 64, the capacity inaccurate flag, CI, is as-
serted in the FLGS1 register. The CPI register is reset
whenever an update of the LMD register is performed,
and the CI flag is also cleared.

Battery Voltage Register (VSB)

The battery voltage register is used to read the single-cell
battery voltage on the SB pin. The VSB register (address
= 0Bh) is updated approximately once per second with the
present value of the battery voltage.
V

= 1.2V * (VSB/256).

VSB Register Bits

VSB7 VSB6 VSB5 VSB4 VSB3 VSB2 VSB1 VSB0

Voltage Threshold Register (VTS)

The end-of-discharge threshold voltages (EDV1 and
EDVF) can be set using the VTS register (address =
0Ch). The VTS register sets the EDV1 trip point. EDVF
is set 25mV below EDV1. The default value in the VTS
register is A2h, representing EDV1 = 0.76V and EDVF =
0.735V. EDV1 = 1.2V * (VTS/256).

VTS Register Bits

VTS7 VTS6 VTS5 VTS4 VTS3 VTS2 VTS1 VTS0

Compensated Available Charge Registers
(CACT/CACD)

The CACD register (address = 0Eh) contains the NAC
value compensated for discharge rate. This is a mono-
tonicly decreasing value during discharge.

If the dis-

charge rate is > 0.5C then this value is lower than NAC.
CACD is updated only when the discharge rate compen-
sated NAC value is a lower value than CACD during
discharge.

During charge, CACD is continuously up-

dated with the NAC value.

The CACT register (address = 0Dh) contains the CACD
value compensated for temperature. CACT will contain
a value lower than CACD when the battery temperature
is below 10

癈. The CACT value is also used in calculat-

ing the LED display pattern.

Scaled Available Energy Registers
(SAEH/SAEL)

The SAEH high-byte register (address = 0Fh) and the
SAEL low-byte register (address = 10h) are used to scale
battery voltage and CACT to a value that can be trans-
lated to watt-hours remaining under the present condi-
tions.

Relative CAC Register (RCAC)

The RCAC register (address = 11h) provides the relative
battery state-of-charge by dividing CACT by LMD.
RCAC varies from 0 to 64h representing relative state-
of-charge from 0 to 100%.

Current Scale Register (VSRH/VSRL)

The VSRH register (address = 12h) and the VSRL regis-
ter (address = 13h) report the average signal across the
SR and V

pins. The bq2050H updates this register

pair every 22.5s. V

SRH

(high-byte) and V

SRL

(low-byte)

form a 16-bit signed integer value representing the av-
erage current during this time. The battery pack current
can be calculated from:

I(mA) = (V

SRH

256 + V

SRL

)/(8

)

where:

= sense resistor value in

SRH

= high-byte value of battery current

SRL

= low-byte value of battery current

The bq2050H indicates an average discharge current
with a "1" in the MSB position of the VSRH register. To
calculate discharge current, use the 2's complement if
the concatenated register contents in the above equa-
tion.

bq2050H

Maximum Cell Voltage Register (NMCV)

The NMCV register (address 15h) is used to set the
maximum battery pack voltage for control of the CFC
pin. If desired, the system can write a value to NMCV to
enable CFC to go low if V

exceeds this value. This

may be useful as a secondary protection of the Li-Ion
battery pack.

NMCV should be set to the

following

equation:

NMCV = 2s complement of

(

)

256

MCV RB2

1.2

RB1 + RB2

Where:

MCV = maximum desired battery stack voltage.

NMCV = set to 00h on power up or reset and

should be programmed to the desired value
by the host system.

Discharge Count Register (DCR)

The DCR register (address = 18h) stores the high-byte of
the discharge count. DCR is reset to zero at the start of
a valid discharge cycle and can count to a maximum of
FFh. DCR will not increment if EDV1 = 1 and will not
roll over from FFh.

Program Pin Full Count (PPFC)

The PPFC register contains information concerning the
program pin configuration. This information is used to
determine the data integrity of the bq2050H. The only
approved user application for this register is to
write a zero to this register as part of a reset re-
quest.

Voltage Offset (V

) Interrupt (INTSS)

The INTSS register (address = 38h) is useful during in-
tial characterization of bq2050H designs.

When the

bq2050H counts a charge pulse, CHGI (bit 0) will be set
to 1.

When the bq2050H counts a discharge pulse,

DCHGI (bit 3) will be set to 1. All other locations in the
INTSS register are reserved.

Reset Register (RST)

The reset register (address = 39h) provides an alternate
means of initializing the bq2050H via software. Since this
register contains device test bits, it is recommended to use
the PPFC and LMD registers to reset the bq2050H. Set-
ting any bits in the reset register is not allowed and
will result in improper bq2050H operation. The rec-
ommended reset method for the bq2050H is :

Write PPFC to zero

Write LMD to zero

After these operations, a software reset will occur.

Resetting the bq2050H sets the following:

LMD = PFC

CPI, VDQ, RCAC, NACH/L, CACH/L, SAEH/L,
NMCV = 0

CI and BRP = 1

Check Register (HEXFF)

The HEXFF register (address = 3F) is useful in de-
terming if the device is a bq2050H or a bq2050. This
register is always set to FFh for the bq2050H.

The

bq2050 returns data other than FFh.

Display

The bq2050H can directly display capacity information
using low-power LEDs. If LEDs are used, the program
pins should be resistively tied to V

or V

for a pro-

gram high or program low, respectively.

The bq2050H displays the battery charge state in relative
mode. In relative mode, the battery charge is represented
as a percentage of the LMD. Each LED segment repre-
sents 20% of the LMD.

The capacity display is also adjusted for the present battery
temperature and discharge rate.

The temperature adjust-

ment reflects the available capacity at a given temperature
but does not affect the NAC register. The temperature adjust-
ments are detailed in the CACT and CACD register descrip-
tions.

When DISP is tied to V

, the SEG

1�5

outputs are inac-

tive. When DISP is left floating, the display becomes ac-
tive whenever the bq2050H detects a charge in progress
V

SRO

> V

SRQ

. When pulled low, the segment outputs be-

come active for a period of four seconds,

� 0.5 seconds.

The segment outputs are modulated as two banks, with seg-
ments 1, 3, and 5 alternating with segments 2 and 4. The
segment outputs are modulated at approximately 100Hz with
each segment bank active for 30% of the period.

SEG

blinks at a 4Hz rate whenever V

has been de-

tected to be below V

EDV1

(EDV1 = 1), indicating a low-

battery condition. V

below V

EDVF

(EDVF = 1) disables

the display output.

Microregulator

A micropower source for the bq2050H can be inexpen-
sively built using a FET and an external resistor. (See
Figure 1.)

bq2050H

DC Voltage Thresholds

(TA = TOPR; V = 3.0 to 6.5V)

Symbol

Parameter

Minimum

Typical

Maximum

Unit

Notes

EDV1

First empty warning

0.73

0.76

0.79

SB, default

EDVF

Final empty warning

EDV1

- 0.035

EDV1

- 0.025

EDV1

- 0.015

SB, default

SRO

SR sense range

-300

+500

SR, V

+ V

SRQ

Valid charge

250

礦

+ V

(see note)

SRD

Valid discharge

-250

礦

+ V

(see note)

MCV

Maximum SB voltage

1.10

1.12

1.15

SB pin

Note:

is affected by PC board layout. Proper layout guidelines should be followed for optimal performance.

See "Layout Considerations."

Absolute Maximum Ratings

Symbol

Parameter

Minimum

Maximum

Unit

Notes

Relative to V

-0.3

+7.0

All other pins

Relative to V

-0.3

+7.0

REF

Relative to V

-0.3

+8.5

Current limited by R1 (see Figure 1)

Relative to V

-0.3

Vcc+0.7

100k

series resistor should be used

to protect SR in case of a shorted bat-
tery.

OPR

Operating temperature

+70

癈

Commercial

Note:

Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional
operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet.
Exposure to conditions beyond the operational limits for extended periods of time may affect device reli-
ability.

bq2050H

bq2050H

DC Electrical Characteristics

(TA = TOPR)

Symbol

Parameter

Minimum Typical

Maximum

Unit

Notes

Supply voltage

3.0

4.25

6.5

excursion from < 2.0V to

3.0V initializes the unit.

Offset referred to V

�50

�150

礦 DISP = VCC

REF

Reference at 25癈

5.7

6.0

6.3

REF

= 5

礎

Reference at -40癈 to +85癈

4.5

7.5

REF

= 5

礎

REF

Reference input impedance

2.0

5.0

REF

= 3V

135

礎 V

= 3.0V, HDQ = 0

Normal operation

120

180

礎 V

= 4.25V, HDQ = 0

170

250

礎 V

= 6.5V, HDQ = 0

Battery input

SBmax

SB input impedance

0 < V

< V

DISP

DISP input leakage

礎 V

DISP

= V

LCOM

LCOM input leakage

-0.2

0.2

礎 DISP = V

RBI

RBI data retention current

100

RBI

> V

< 3V

HDQ

Internal pulldown

500

SR input impedance

-200mV < V

< V

IHPFC

Logic input high

- 0.2

PROG

1�5

ILPFC

Logic input low

+ 0.2

PROG

1�5

IZPFC

Logic input Z

float

PROG

1�5

OLSL

SEG output low, low V

0.1

= 3V, I

OLS

1.75mA

SEG

璖EG

, CFC

OLSH

SEG output low, high V

0.4

= 6.5V, I

OLS

11.0mA

SEG

璖EG

, CFC

OHML

LCOM output high, low V

- 0.3

= 3V, I

OHLCOM

= -5.25mA

OHMH

LCOM output high, high V

- 0.6

> 3.5V, I

OHLCOM

= -33.0mA

OLS

SEG sink current

11.0

At V

OLSH

= 0.4V, V

= 6.5V

Open-drain sink current

5.0

At V

= V

+ 0.3V, HDQ

Open-drain output low

0.3

5mA, HDQ

IHDQ

HDQ input high

2.5

HDQ

ILDQ

HDQ input low

0.8

HDQ

Logic input high

2.5

PSTAT

Logic input low

0.5

PSTAT

PROG

Soft pull-up or pull-down resis-
tor value (for programming)

200

PROG

�

FLOAT

Float state external impedance

PROG

�

Note:

All voltages relative to V

bq2050H

High-Speed Serial Communication Timing Specification

(TA = TOPR)

Symbol

Parameter

Minimum

Typical

Maximum

Unit

Notes

CYCH

Cycle time, host to bq2050H (write)

190

祍

See note

CYCB

Cycle time, bq2050H to host (read)

190

205

250

祍

STRH

Start hold, host to bq2050H (write)

STRB

Start hold, bq2050H to host (read)

祍

DSU

Data setup

祍

DSUB

Data setup

祍

Data hold

祍

Data valid

祍

SSU

Stop setup

145

祍

SSUB

Stop setup

145

祍

RSPS

Response time, bq2050H to host

190

320

祍

Break

190

祍

Break recovery

祍

Note:

The open-drain HDQ pin should be pulled to at least V

by the host system for proper HDQ operation.

HDQ may be left floating if the serial interface is not used.

bq2050H

Package Option:

SN = 16-pin narrow SOIC

Device:

bq2050H Power Gauge IC

Temperature Range:

blank = Commercial (0 to +70癈)

Ordering Information

ChangeNo.

Page No.

Description of Change

All

"Final" changes from "Preliminary" version

Digital magnitude filter changed from 200

礦 to 250礦.

VSRQ changed from 200

礦(min) to 250礦(min).

VSRD changed from -200

礦(max) to -250礦(max).

Updated application diagram

Changed designation on appropriate locations from "R/W" to "R"

Clarified current scale register description

Changed V

SRO

max. from +2000mV to +500mV

Changed V

max. from 0.5V to 0.3V

Changed t

SSUB

max. from 95

祍 to 145祍

Notes:

Change 1 = Aug. 1997 B changes from June 1996 "Preliminary."
Change 2 = June 1998 C changes from Aug. 1997 B.
Change 3 = May 1999 D changes from June 1998 C.

Data Sheet Revision History

IMPORTANT NOTICE

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any
product or service without notice, and advise customers to obtain the latest version of relevant information to verify,
before placing orders, that information being relied on is current and complete. All products are sold subject to the
terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty,
patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accor-
dance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems
necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, ex-
cept those mandated by government requirements.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH,
PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI
SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR
USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI
PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK.

In order to minimize risks associated with the customer's applications, adequate design and operating safeguards
must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that
any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellec-
tual property right of TI covering or relating to any combination, machine, or process in which such semiconductor
products or services might be or are used. TI's publication of information regarding any third party's products or ser-
vices does not constitute TI's approval, warranty or endorsement thereof.

协谢械泻褌褉芯薪薪褘泄 泻芯屑锌芯薪械薪褌: BQ2050H

协谢械泻褌褉芯薪薪褘泄泻芯屑锌芯薪械薪褌: BQ2050H