ICS601-02
Low Phase Noise Clock Multiplier
MDS 601-02
D
1
Revision
111204
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800tel www.icst.com
The ICS601-02 is a low cost, low phase noise, high
performance clock synthesizer for any application that
requires low phase noise and low jitter. The ICS601 is
ICS' lowest phase noise multiplier. Using ICS' patented
analog and digital Phase Locked Loop (PLL)
techniques, the chip accepts a 10-27 MHz crystal or
clock input, and produces output clocks up to 170
MHz at 3.3 V. A separate supply pin is provided so that
the output can be 2.5 V.
This product is intended for clock generation. It has low
output jitter (variation in the output period), but input to
output skew and jitter are not defined nor guaranteed.
For applications which require defined input to output
timing, use the ICS670-01.
Block Diagram
Description
Features
Packaged in 16 pin SOIC
(Pb free)
Uses fundamental 10 - 27 MHz crystal, or clock
Patented PLL with the lowest phase noise
Output clocks up to 170 MHz at 3.3 V
Low phase noise: -132 dBc/Hz at 10 kHz
Output Enable function tri states outputs
Low jitter - 18 ps one sigma
Full swing CMOS outputs with 25 mA drive
capability at TTL levels
Advanced, low power, sub-micron CMOS process
Industrial temperature
3.3 V or 5 V core VDD. Output clock can operate
down to 2.5 V
Reference
Divide
Phase
Comparator
Crystal
Oscillator
ROM Based
Multipliers
VCO
Divide
Charge
Pump
Loop
Filter
VCO
Output
Buffer
X1/ICLK
X2
S0
S1
VDD
GND
OE
CLK
S3 S2
VDDP
Optional crystal
capacitors
needed
for accurate
tuning
(not shown)
ICS601-02
Low Phase Noise Clock Multiplier
MDS 601-02
D
2
Revision
111204
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800tel www.icst.com
Pin Descriptions
Key: I = Input with internal pull-up resistor; O = output; P = power supply connection; XI, X2 = crystal connections.
Pin Assignment
Number
Name
Type
Description
1
CLK
O
Clock output from VCO. Output frequency equals the input frequency times multiplier.
2
VDDP
P
Supply pin for CLK output buffer. Sets output clock amplitude. Connect to 2.5V or 3.3V
3
VDD
P
Connect to +3.3V or +5V. Must match other VDDs.
4
VDD
P
Connect to +3.3V or +5V. Must match other VDDs.
5
VDD
P
Connect to +3.3V or +5V. Must match other VDDs.
6
X2
XO
Crystal connection. Connect to a 10 - 27 MHz fundamental parallel mode crystal.
7
S1
I
Multiplier select pin 1. Determines CLK output per table above. Internal pull-up.
8
X1/ICLK
XI
Crystal connection. Connect to a 10-27 MHz fundamental parallel mode crystal, or clock.
9
S2
I
Multiplier select pin 2. Determines CLK output per table above. Internal pull-up.
10
S3
I
Multiplier select pin 3. Determines CLK output per table above. Internal pull-up.
11
S0
I
Multiplier select pin 0. Determines CLK output per table above. Internal pull-up.
12
OE
I
Output Enable. Tri-states the output clock when low. Internal pull-up.
13
GND
P
Connect to ground.
14
GND
P
Connect to ground.
15
GND
P
Connect to ground.
16
GND
P
Connect to ground.
0=connect directly to ground
1=connect directly to VDD
1
8
9
16
2
3
4
5
6
7
10
11
12
13
14
15
S0
GND
GND
GND
OE
CLK
VDDP
S1
X2
VDD
VDD
VDD
X1/ICLK
S3
GND
S2
S3
S2
S1
S0
CLK (see note 2 on following page)
0
0
0
0
Input x4/3
0
0
0
1
Input x4
0
0
1
0
Input x25/4
0
0
1
1
Input x3
0
1
0
0
Input x7.5
0
1
0
1
Input x5
0
1
1
0
Input x6
0
1
1
1
Input x8
1
0
0
0
Input x8/3
1
0
0
1
Input x8
1
0
1
0
Input x12.5
1
0
1
1
Input x6
1
1
0
0
Input x15
1
1
0
1
Input x10
1
1
1
0
Input x12
1
1
1
1
Input x16
Multiplier Select Table
ICS601-02
Low Phase Noise Clock Multiplier
MDS 601-02
D
3
Revision
111204
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800tel www.icst.com
-140
-120
-100
-80
-60
-40
-20
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Offset from Carrier (Hz)
Phase Noise (dBc/Hz)
Figure 1. Phase Noise of ICS601-02 at 125 MHz out, 25 MHz crystal input, VDD =
3 . 3 V .
Figure 1 shows a typical phase noise measurement in a 125 MHz system. There are a few simple steps that can be
taken to achieve these levels of phase noise from the ICS601-02. Variations in VDD will increase the phase noise, so
it is important to have a stable, low noise supply voltage at the device. Use decoupling capacitors of 0.1 F in parallel
with 0.01 F. It is important to have these capacitors as close as possible to the ICS601-02 supply pins.
Disabling the REFOUT clock is also important for achieving low phase noise; lab tests have shown that this can
reduce the phase noise by as much as 10 dBc/Hz.
Achieving Low Phase Noise
External Components/Crystal Selection
The ICS601-02 requires a minimum number of external components for proper operation. Decoupling capacitors of
0.01 F and 0.1 F should be connected between VDD and GND, as close to the part as possible. A series
termination resistor of 33
may be used for the clock output. The crystal must be connected as close to the chip as
possible. The crystal should be fundamental mode, parallel resonant. Do not use third overtone. For exact tuning
when using a crystal, capacitors should be connected from pins X1 to ground and X2 to ground. In general, the value
of these capacitors is given by the following equation, where CL is the crystal load capacitance: Crystal caps (pF) =
(CL-5) x 2. So for a crystal with 16 pF load capacitance, two 22 pF caps can be used. For any given board layout, ICS
can measure the board capacitance and recommend the exact capacitance value to use.
ICS601-02
Low Phase Noise Clock Multiplier
MDS 601-02
D
4
Revision
111204
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800tel www.icst.com
Parameter
Conditions
Minimum
Typical
Maximum
Units
ABSOLUTE MAXIMUM RATINGS (note 1)
ABSOLUTE MAXIMUM RATINGS (note 1)
Supply voltage, VDD
Referenced to GND
7
V
Inputs and Clock Outputs
Referenced to GND
-0.5
VDD+0.5
V
Ambient Operating Temperature, I version
Industrial temperature
-40
85
C
Soldering Temperature
Max of 10 seconds
260
C
Storage temperature
-65
150
C
DC CHARACTERISTICS (VDD = VDDP = 3.3 V unless noted)
DC CHARACTERISTICS (VDD = VDDP = 3.3 V unless noted)
DC CHARACTERISTICS (VDD = VDDP = 3.3 V unless noted)
Operating Voltage, VDD
3.0
5.5
V
Output Buffer Voltage, VDDP
2.375
VDD
V
Input High Voltage, VIH, X1/ICLK pin only
Note 3
(VDD/2)+1
V
Input Low Voltage, VIL, X1/ICLK pin only
Note 3
(VDD/2)-1
V
Input High Voltage, VIH
2
V
Input Low Voltage, VIL
0.8
V
Output High Voltage, VOH, CMOS level
IOH=-4mA
VDD-0.4
V
Output High Voltage, VOH
IOH=-12mA
2.4
V
Output Low Voltage, VOL
IOL=12mA
0.4
V
Operating Supply Current, IDD
No Load, 125 MHz
9
20
mA
Short Circuit Current
Each output
40
60
mA
Input Capacitance
OE, select pins
5
pF
AC CHARACTERISTICS (VDD = VDDP = 3.3 V unless noted)
AC CHARACTERISTICS (VDD = VDDP = 3.3 V unless noted)
AC CHARACTERISTICS (VDD = VDDP = 3.3 V unless noted)
Input Frequency
10
27
MHz
Output Frequency
at 3.3V or 5V
170
MHz
Output Clock Rise Time
0.8 to 2.0V, no load
1.5
ns
Output Clock Fall Time
0.8 to 2.0V, no load
1.5
ns
Output Clock Duty Cycle
At VDD/2
45
50
55
%
Maximum Absolute Jitter, short term, 125 MHz No load
50
75
ps
Maximum Jitter, one sigma, 125 MHz (x5)
No load
18
25
ps
Phase Noise, relative to carrier, 125 MHz (x5)
100 Hz offset
-108
dBc/Hz
Phase Noise, relative to carrier, 125 MHz (x5)
1 kHz offset
-123
dBc/Hz
Phase Noise, relative to carrier, 125 MHz (x5)
10 kHz offset
-132
dBc/Hz
Phase Noise, relative to carrier, 125 MHz (x5)
100 kHz offset
-125
dBc/Hz
Electrical Specifications
Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the
device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may
affect device reliability.
2. The phase relationship between input and output can change at power up. For a fixed phase
relationship, see the ICS570 or ICS670.
3. Switching occurs nominally at VDD/2.
ICS601-02
Low Phase Noise Clock Multiplier
MDS 601-02
D
5
Revision
111204
Integrated Circuit Systems, Inc. 525 Race Street San Jose CA95126 (408) 295-9800tel www.icst.com
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems,
Incorporated (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third
parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in
normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or
other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the
right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life
support devices or critical medical instruments.
Package Outline and Package Dimensions
(For current dimensional specifications, see JEDEC no. 95.)
Ordering Information
Part/Order Number
Marking
Shipping packaging
Package
Temperature
ICS601M-02I
ICS601M-02I
tubes
16 pin narrow SOIC
-40 to 85 C
ICS601M-02IT
ICS601M-02I
tape and reel
16 pin narrow SOIC
-40 to 85 C
16 pin SOIC
Inches
Inches
Millimeters
Millimeters
Symbol
Min
Max
Min
Max
A
0.0532
0.0688
1.35
1.75
A1
0.0040
0.0098
0.10
0.24
B
0.0130
0.0200
0.33
0.51
C
0.0075
0.0098
0.19
0.24
D
0.3859
0.3937
9.80
10.00
E
0.1497
0.1574
3.80
4.00
e .050 BSC
.050 BSC
1.27 BSC
1.27 BSC
H
0.2284
0.2440
5.80
6.20
h
0.0099
0.0195
0.25
0.50
L
0.0160
0.0500
0.41
1.27
B
D
E
H
e
A1
C
A
h x 45
L
INDEX
AREA
ICS601M-02ILF
ICS601M-02ILFT
ICS601M-02IL
ICS601M-02IL
tubes
tape and reel
16 pin narrow SOIC
16 pin narrow SOIC
-40 to 85 C
-40 to 85 C
PDF 
ZIP