Integrated Device Technology, Inc.
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
FUNCTIONAL BLOCK DIAGRAM
FAST CMOS 16-BIT BUS
TRANSCEIVER/
REGISTERS (3-STATE)
IDT54/74FCT16646T/AT/CT/ET
IDT54/74FCT162646T/AT/CT/ET
1
B
1
1
A
1
1
OE
1
DIR
1
SBA
1
SAB
1
CLKBA
1
CLKAB
2540 drw 01
TO 7 OTHER CHANNELS
B REG
A REG
D
C
C
D
2
A
1
2
OE
2
DIR
2
SBA
2
SAB
2
B
1
2
CLKBA
2
CLKAB
2540 drw 02
TO 7 OTHER CHANNELS
B REG
A REG
D
C
C
D
74FCT162646T/AT/CT/ET 16-bit registered transceivers are
built using advanced dual metal CMOS technology. These
high-speed, low-power devices are organized as two inde-
pendent 8-bit bus transceivers with 3-state D-type registers.
The control circuitry is organized for multiplexed transmission
of data between A bus and B bus either directly or from the
internal storage registers. Each 8-bit transceiver/register fea-
tures direction control (xDIR), over-riding Output Enable con-
trol (x
OE
) and Select lines (xSAB and xSBA) to select either
real-time data or stored data. Separate clock inputs are
provided for A and B port registers. Data on the A or B data
bus, or both, can be stored in the internal registers by the
LOW-to-HIGH transitions at the appropriate clock pins. Flow-
through organization of signal pins simplifies layout. All inputs
are designed with hysteresis for improved noise margin.
The IDT54/74FCT16646T/AT/CT/ET are ideally suited for
driving high-capacitance loads and low-impedance
backplanes. The output buffers are designed with power off
disable capability to allow "live insertion" of boards when used
as backplane drivers.
The IDT54/74FCT162646T/AT/CT/ET have balanced
output drive with current limiting resistors. This offers low
ground bounce, minimal undershoot, and controlled output
fall timesreducing the need for external series terminating
resistors. The IDT54/74FCT162646T/AT/CT/ET are plug-in
replacements for the IDT54/74FCT16646T/AT/CT/ET and
54/74ABT16646 for on-board bus interface applications.
MILITARY AND COMMERCIAL TEMPERATURE RANGES
AUGUST 1996
1996 Integrated Device Technology, Inc.
5.13
DSC-4231/9
1
DESCRIPTION:
The IDT54/74FCT16646T/AT/CT/ET and IDT54/
FEATURES:
Common features:
0.5 MICRON CMOS Technology
High-speed, low-power CMOS replacement for
ABT functions
Typical t
SK
(o) (Output Skew) < 250ps
Low input and output leakage
1
A (max.)
ESD > 2000V per MIL-STD-883, Method 3015;
> 200V using machine model (C = 200pF, R = 0)
Packages include 25 mil pitch SSOP, 19.6 mil pitch
TSSOP, 15.7 mil pitch TVSOP and 25 mil pitch Cerpack
Extended commercial range of -40
C to +85
C
V
CC
= 5V
10%
Features for FCT16646T/AT/CT/ET:
High drive outputs (-32mA I
OH
, 64mA I
OL
)
Power off disable outputs permit "live insertion"
Typical V
OLP
(Output Ground Bounce) < 1.0V at
V
CC
= 5V, T
A
= 25
C
Features for FCT162646T/AT/CT/ET:
Balanced Output Drivers:
24mA (commercial),
16mA (military)
Reduced system switching noise
Typical V
OLP
(Output Ground Bounce) < 0.6V at
V
CC
= 5V,T
A
= 25
C
5.13
2
IDT54/74FCT16646T/AT/CT/ET, 162646T/AT/CT/ET
FAST CMOS 16-BIT BUS TRANSCEIVER/REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
PIN CONFIGURATIONS
1DIR
1
CLKAB
1
SAB
GND
1
A
1
1
A
2
V
CC
1
A
3
1
A
4
GND
1
A
5
1
A
6
1
A
7
1
A
8
GND
2
A
1
2
A
2
V
CC
2
A
3
2
SAB
2
A
5
2
A
4
2
A
7
GND
2
A
8
2
CLKAB
2
DIR
2
A
6
1
B
1
1
B
2
GND
1
B
3
1
B
4
V
CC
1
B
5
1
B
6
1
SBA
1
B
7
1
B
8
2
B
1
2
B
2
GND
2
B
3
2
B
4
V
CC
2
B
5
GND
1
CLKBA
2
B
7
2
B
6
2
B
8
GND
2
SBA
2
CLKBA
1
OE
2
OE
47
37
38
39
40
41
42
43
44
45
46
33
34
35
36
56
55
49
50
51
52
53
54
48
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
11
21
22
23
24
29
30
31
32
25
26
27
28
2540 drw 04
CERPACK
TOP VIEW
E56-1
1
B
1
1
B
2
GND
1
B
3
1
B
4
V
CC
1
B
5
1
B
6
1
OE
1
SBA
1
B
7
1
B
8
2
B
1
2
B
2
GND
2
B
3
2
B
4
V
CC
2
B
5
GND
1
CLKBA
2
B
7
2
B
6
2
B
8
GND
2
SBA
2
CLKBA
2
OE
1DIR
1
CLKAB
1
SAB
GND
1
A
1
1
A
2
V
CC
1
A
3
1
A
4
GND
1
A
5
1
A
6
1
A
7
1
A
8
GND
2
A
1
2
A
2
V
CC
2
A
3
2
SAB
2
A
5
2
A
4
2
A
7
GND
2
A
8
2
CLKAB
2
DIR
2
A
6
2540 drw 03
47
37
38
39
40
41
42
43
44
45
46
33
34
35
36
56
55
49
50
51
52
53
54
48
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
11
21
22
23
24
SSOP/
TSSOP/TVSOP
TOP VIEW
SO56-1
SO56-2
SO56-3
29
30
31
32
25
26
27
28
IDT54/74FCT16646T/AT/CT/ET, 162646T/AT/CT/ET
FAST CMOS 16-BIT BUS TRANSCEIVER/REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
5.13
3
PIN DESCRIPTION
FUNCTION TABLE
(2)
CAPACITANCE
(T
A
= +25
C, f = 1.0MHz)
2540 tbl 01
NOTE:
1. This parameter is measured at characterization but not tested.
2540 tbl 02
NOTES:
2540 tbl 03
1. The data output functions may be enabled or disabled by various signals at the x
OE
or xDIR inputs. Data
input functions are always enabled, i.e. data at the bus pins will be stored on every LOW-to-HIGH transition
on the clock inputs.
2. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
= LOW-to-HIGH Transition
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Parameter
(1)
Conditions
Typ.
Max.
Unit
C
IN
Input
Capacitance
V
IN
= 0V
3.5
6.0
pF
C
I/O
I/O
Capacitance
V
OUT
= 0V
3.5
8.0
pF
Pin Names
Description
xAx
Data Register A Inputs
Data Register B Outputs
xBx
Data Register B Inputs
Data Register A Outputs
xCLKAB, xCLKBA Clock Pulse Inputs
xSAB, xSBA
Output Data Source Select Inputs
xDIR, x
OE
Output Enable Inputs
Inputs
Data I/O
(1)
Operation or Function
x
OE
OE
xDIR
xCLKAB
xCLKBA
xSAB
xSBA
xAx
xBx
H
H
X
X
H or L
H or L
X
X
X
X
Input
Input
Isolation
Store A and B Data
L
L
L
L
X
X
X
H or L
X
X
L
H
Output
Input
Real Time B Data to A Bus
Stored B Data to A Bus
L
L
H
H
X
H or L
X
X
L
H
X
X
Input
Output
Real Time A Data to B Bus
Stored A Data to B Bus
Symbol
Description
Max.
Unit
V
TERM(2)
Terminal Voltage with Respect to
GND
0.5 to +7.0
V
V
TERM(3)
Terminal Voltage with Respect to
GND
0.5 to
V
CC
+0.5
V
T
STG
Storage Temperature
65 to +150
C
I
OUT
DC Output Current
60 to +120 mA
2540 tbl 04
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RAT-
INGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
2. All device terminals except FCT162XXXT Output and I/O terminals.
3. Output and I/O terminals for FCT162XXXT.
5.13
4
IDT54/74FCT16646T/AT/CT/ET, 162646T/AT/CT/ET
FAST CMOS 16-BIT BUS TRANSCEIVER/REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
BUS
A
BUS
B
x
DIR
x
OE
x
CLKAB
x
CLKBA
x
SAB
x
SBA
H
L
X
X
L
X
2540 drw 06
TRANSFER STORED
DATA TO A AND/OR B
NOTE:
1. Cannot transfer data to A bus and B bus simultaneously.
BUS
A
BUS
B
x
DIR
x
OE
x
CLKAB
x
CLKBA
x
SAB
x
SBA
L
L
X
X
X
H
X
X
L
X
X
H
L
X
X
X
2540 drw 07
REAL-TIME TRANSFER
BUS B TO A
REAL-TIME TRANSFER
BUS A TO B
STORAGE FROM
A AND/OR B
BUS
A
BUS
B
x
DIR
x
OE
x
CLKAB
x
CLKBA
x
SAB
x
SBA
L
L
X
X
X
L
2540 drw 05
BUS
A
BUS
B
x
DIR
x
OE
x
CLKAB
x
CLKBA
x
SAB
x
SBA
L
L
X
X
H or L
H
2540 drw 08
(1)
H
L
H or L
X
H
X
IDT54/74FCT16646T/AT/CT/ET, 162646T/AT/CT/ET
FAST CMOS 16-BIT BUS TRANSCEIVER/REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
5.13
5
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: T
A
= 40
C to +85
C, V
CC
= 5.0V
10%; Military: T
A
= 55
C to +125
C, V
CC
= 5.0V
10%
2540 lnk 06
2540 lnk 07
Symbol
Parameter
Test Conditions
(1)
Min.
Typ.
(2)
Max.
Unit
I
ODL
Output LOW Current
V
CC
= 5V, V
IN
= V
IH
or
V
IL,
V
OUT
= 1.5V
(3)
60
115
200
mA
I
ODH
Output HIGH Current
V
CC
= 5V, V
IN
= V
IH
or V
IL,
V
OUT
= 1.5V
(3)
60
115
200
mA
V
OH
Output HIGH Voltage
V
CC
= Min.
V
IN
= V
IH
or V
IL
I
OH
= 16mA MIL.
I
OH
= 24mA COM'L.
2.4
3.3
--
V
V
OL
Output LOW Voltage
V
CC
= Min.
V
IN
= V
IH
or V
IL
I
OL
= 16mA MIL.
I
OL
= 24mA COM'L.
--
0.3
0.55
V
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25
C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. Duration of the condition can not exceed one second.
5. The test limit for this parameter is
5
A at T
A
= 55
C.
Symbol
Parameter
Test Conditions
(1)
Min.
Typ.
(2)
Max.
Unit
V
IH
Input HIGH Level
Guaranteed Logic HIGH Level
2.0
--
--
V
V
IL
Input LOW Level
Guaranteed Logic LOW Level
--
--
0.8
V
I
I H
Input HIGH Current (Input pins)
(5)
V
CC
= Max.
V
I
= V
CC
--
--
1
A
Input HIGH Current (I/O pins)
(5)
--
--
1
I
I L
Input LOW Current (Input pins)
(5)
V
I
= GND
--
--
1
Input LOW Current (I/O pins)
(5)
--
--
1
I
OZH
High Impedance Output Current
V
CC
= Max.
V
O
= 2.7V
--
--
1
A
I
OZL
(3-State Output pins)
(5)
V
O
= 0.5V
--
--
1
V
IK
Clamp Diode Voltage
V
CC
= Min., I
IN
= 18mA
--
0.7
1.2
V
I
OS
Short Circuit Current
V
CC
= Max., V
O
= GND
(3)
80
140
225
mA
V
H
Input Hysteresis
--
--
100
--
mV
I
CCL
I
CCH
I
CCZ
Quiescent Power Supply Current
V
CC
= Max., V
IN
= GND or V
CC
--
5
500
A
2540 lnk 05
Symbol
Parameter
Test Conditions
(1)
Min.
Typ.
(2)
Max.
Unit
I
O
Output Drive Current
V
CC
= Max., V
O
= 2.5V
(3)
50
--
180
mA
V
OH
Output HIGH Voltage
V
CC
= Min.
I
OH
= 3mA
2.5
3.5
--
V
V
IN
= V
IH
or V
IL
I
OH
= 12mA MIL.
I
OH
= 15mA COM'L.
2.4
3.5
--
V
I
OH
= 24mA MIL.
I
OH
= 32mA COM'L.
(4)
2.0
3.0
--
V
V
OL
Output LOW Voltage
V
CC
= Min.
V
IN
= V
IH
or V
IL
I
OL
= 48mA MIL.
I
OL
= 64mA COM'L.
--
0.2
0.55
V
I
OFF
Input/Output Power Off Leakage
(5)
V
CC
= 0V, V
IN
or V
O
4.5V
--
--
1
A
OUTPUT DRIVE CHARACTERISTICS FOR FCT16646T
OUTPUT DRIVE CHARACTERISTICS FOR FCT162646T
PDF 
ZIP