ChipFind - документация

Электронный компонент: ILA3654

Скачать:  PDF   ZIP
ILA3654,ILA3654Q
Korzhenevskogo 12, Minsk, 220064, Republic of
Belarus
Fax: +375 (17) 278 28 22,
Phone: +375 (17) 278 07 11, 277 24 70, 277 24 61,
277 69 16
E-mail: belms@belms.belpak.minsk.by
URL: www.bms.by
V
ERTICAL DEFLECTION AND GUARD CIRCUIT
(110)
GENERAL DESCRIPTION
The ILA3654 is a full performance vertical deflection output circuit for direct drive of the
deflection coils and can be used for a wide range of 90 and 110 deflection systems.
A guard circuit is provided which blanks the picture tube screen in the absence of
deflection current.

FEATURES
Direct drive to the deflection coils
90 and 110 deflection system
Internal blanking guard circuit
Internal voltage stabilizer

QUICK REFERENCE DATA
Output voltage
V5-2
max.
60 V
Output current (peak-to-peak)
I5(p-p)
max.
3 A
Supply voltage
V9-2
max.
40 V
Guard circuit output voltage
V7-2
max.
5,6 V
Operating ambient temperature range
Tamb
-25 to +60 C
Storage temperature
Tstg
-55 to +150 C
THERMAL RESISTANCE
From junction to mounting base Rth j-mb 3,5 to 4 K/W
BLOCK DIAGRAM.
.
ILA3654,ILA3654Q
Korzhenevskogo 12, Minsk, 220064, Republic of
Belarus
Fax: +375 (17) 278 28 22,
Phone: +375 (17) 278 07 11, 277 24 70, 277 24 61,
277 69 16
E-mail: belms@belms.belpak.minsk.by
URL: www.bms.by
FUNCTIONAL DESCRIPTION
Output stage and protection circuits
The output stage consists of two Darlington configurations in class B arrangement.
Each output transistor can deliver 1,5 A maximum and the VCEO is 60 V.
Protection of the output stage is such that the operation of the transistors remains well
within the SOAR area in all
circumstances at the output pin, (pin 5). This is obtained by the cooperation of the thermal
protection circuit, the
current-voltage detector and the short circuit protection.
Special measures in the internal circuit layout give the output transistors extra solidity.
The supply for the output stage is fed to pin 6 and the output stage ground is connected to
pin 4.
Driver and switching circuit
Pin 1 is the input for the driver of the output stage. The signal at pin 1 is also applied to pin
3 which is the input of a
switching circuit (pin 1 and 3 are connected via external resistors).
This switching circuit rapidly turns off the lower output stage when the flyback starts and it,
therefore, allows a quick start
of the flyback generator. The maximum required input signal for the maximum output
current peak-to-peak value of 3 A
is only 3 V, the sum of the currents in pins 1 and 3 is then maximum 1 mA.
Flyback generator
During scan, the capacitor between pins 6 and 8 is charged to a level which is dependent
on the value of the resistor at
pin 8 (see Fig.1).
When the flyback starts and the voltage at the output pin (pin 5) exceeds the supply
voltage, the flyback generator is activated.
The supply voltage is then connected in series, via pin 8, with the voltage across the
capacitor during the flyback period.
This implies that during scan the supply voltage can be reduced to the required scan
voltage plus saturation voltage of the output transistors.
The amplitude of the flyback voltage can be chosen by changing the value of the external
resistor at pin 8.
It should be noted that the application is chosen such that the lowest voltage at pin 8 is >
1,5 V, during normal operation.
Guard circuit
When there is no deflection current, for any reason, the voltage at pin 8 becomes less than
1 V, the guard circuit will
produce a d.c. voltage at pin 7. This voltage can be used to blank the picture tube, so that
the screen will not burn in.

Voltage stabilizer
The internal voltage stabilizer provides a stabilized supply of 6 V to drive the output stage,
so the drive current is not
affected by supply voltage variations.
ILA3654,ILA3654Q
Korzhenevskogo 12, Minsk, 220064, Republic of
Belarus
Fax: +375 (17) 278 28 22,
Phone: +375 (17) 278 07 11, 277 24 70, 277 24 61,
277 69 16
E-mail: belms@belms.belpak.minsk.by
URL: www.bms.by
RATINGS
Voltages
Output voltage
Vs.4
O to 60
V
Supply voltage
Vg-4
O to 40
V
Supply voltage output stage
Ve.4
O to 60
V
Input voltage
Vl-2
0 to Vg-4
V
Input voltage switching circuit
Va.2
0 to Vs.4
V
External voltage at pin 7
V7-2
0 to 5,6
V
Currents
Repetitive peak output current
l5RM
max.
1.5
A
Non-repetitive peak output
current (note 1)
l5SM max.
3
A
Repetitive peak output current of
flyback generator
IBRM
max.
+1,5
A
-
1.6
A
Non-repetitive peak output
current of flyback generator (note
1)
l8SM max.
3
A
Temperatures
Storage temperature range
Ts,g
-65 to + 150
C
Operating ambient temperature
range

-25 10 + 60
"C
Operating junction temperature
range
Tj -25to+
150
C
(the output current at pin 5
should not exceed 2.5A)




ILA3654 or ILA3654Q