- 1 -
Nov. 2004
(Rev. 1)
www.interpionsemi.com
IP4001S
5-CH MOTOR DRIVE IC
The IP4001S is a monolithic integrated circuit, and
suitable for 5-ch motor driver which drives focus
actuator, tracking actuator, sled motor, spindle motor
and tray motor of CDP & V-CD system .Each channel
excluding the tray channel driver is a fixed gain driver
- Logic controlled 1-CH DC motor driver
- 4-CH BTL(Balanced Transformerless) drivers
- Built-in TSD (Thermal shutdown) circuit
- Built-in 5V regulator with an internal NPN TR
- Built-in mute circuit
- Built-in tray motor speed control circuit
- Wide operating supply voltage range: 6.5V~13.2V
DESCRIPTIONS
BLOCK DIAGRAM
ORDER INFORMATION
FEATURES
28SSOP H/S
Device
Order Coder
Package
Packing
IP4001S
IP4001S
28SSOPH-375B
Tube
IP4001S-TF
T&R
IP4001SL
Tube, Lead Free
IP4001SL-TF
T&R, Lead Free
- 2 -
Nov. 2004
(Rev. 1)
www.interpionsemi.com
IP4001S
5-CH MOTOR DRIVE IC
PIN DESCRIPTIONS
NO
SYMBOL
I/O
DESCRIPTION
1
DO1-
O
CH1 OUTPUT (-)
2
DO1+
O
CH1 OUTPUT (+)
3
IN1
I
CH1 INPUT
4
N/C
-
NO CONNECTION
5
N/C
-
NO CONNECTION
6
REO
O
REGULATOR
OUTPUT
7
MUTE
I
MUTE
INPUT
8
SGND
-
SIGNAL
GROUND
9
FWD
I
CH5 INPUT 1
10
IN2
I
CH2 INPUT
11
DO2+
O
CH2 OUTPUT (+)
12
DO2-
O
CH2 OUTPUT (-)
13
PGND1
-
POWER GROUND 1
14
REV
I
CH5 INPUT 2
NO
SYMBOL
I/O
DESCRIPTION
15
DO5+
O
CH5 OUTPUT (+)
16
DO5-
O
CH5 OUTPUT (-)
17
DO3-
O
CH3 OUTPUT (-)
18
DO3+
O
CH3 OUTPUT (+)
19
IN3
I
CH3 INPUT
20
CTL
I
CH5 MOTOR SPEED
CONTROL INPUT
21
VCC1
-
SUPPLY VOLTAGE 1
(CH2,CH3,CH5)
22
VCC2
-
SUPPLY VOLTAGE 2
(CH1,CH4,SIGNAL,REG)
23
REF
I
REFERENCE INPUT
24
N/C
-
NO CONNECTION
25
IN4
I
CH4 INPUT
26
DO4+
O
CH4 OUTPUT (+)
27
DO4-
O
CH4 OUTPUT (-)
28
PGND2
-
POWER GROUND 2
PIN CONNECTIONS
- 3 -
Nov. 2004
(Rev. 1)
www.interpionsemi.com
IP4001S
5-CH MOTOR DRIVE IC
CHARACTERISTICS
SYMBOL
VALUE
UNIT
Maximum supply voltage
Vccmax
18
V
Power dissipation
Pd
2.3 *
W
Operating temperature
Topr
-35 ~ +85
O
C
Storage temperature
Tstg
-55 ~ 150
O
C
Maximum output current
Iomax
1
A
Note>
1. When mounted on 50mm X 50mm X 1mm PCB (Phenolic resin material).
2. Power dissipation reduces 18.4 mW/
O
C for using above Ta=25
O
C
3. Do not exceed Pd and SOA.
POWER DISSIPATION CURVE
P
o
w
e
r
D
i
s
s
i
p
a
t
i
o
n
(
W
)
Ambient Temperature (
C)
25 50 75 100 125 150 175
0
1
2
3
RECOMMENDED OPERATING CONDITIONS
CHARACTERISTICS
SYMBOL
VALUE
UNIT
Supply voltage 1
VCC1
*6.5 ~ 13.2
V
Supply voltage 2
VCC2
*6.5 ~ 13.2
V
SOA
ABSOLUTE MAXIMUM RATINGS
* IF you don
'
t use regulator, then the recommended operating voltage is 4.5V ~ 13.2V
- 4 -
Nov. 2004
(Rev. 1)
www.interpionsemi.com
IP4001S
5-CH MOTOR DRIVE IC
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
Quiescent circuit current
Icc
RL=open
-
5.5
-
mA
Mute on current
Imute
Pin7=GND
-
2.5
5
mA
Mute on voltage
Vmon
-
-
-
0.5
V
Mute off voltage
Vmoff
-
2
-
-
V
[ BTL DRIVE PART ]
Output offset voltage
Voo
Vin=2.5V
-80
-
+80
mV
Vom1
Actuator Part
(CH1 and CH4)
3.5
4.5
-
V
Vom2
Spindle and Sled Part
(CH2 and CH3)
3.7
4.7
-
Closed-loop voltage gain
Avf
Vin=0.1Vrms, f=1Khz
5
6.5
8
dB
Ripple rejection ratio
RR
Vin=0.1Vrms, f=120Hz
40
60
-
dB
Slew rate
SR
Vout=4Vp-p, square
-
1.5
-
V/us
[ REGULATOR PART ]
Output voltage
Vreg
IL=100mA
4.7
5
5.3
V
Load regulation
Vrl
IL=0~100mA
-
20
-
mV
Line regulation
Vcc
VCC=8V~13.2V, IL=100mA
-
60
-
mV
[ TRAY DRIVE PART ]
Input high level voltage
Vih
-
2.5
-
-
V
Input low level voltage
Vil
-
-
-
0.5
V
Output voltage
Vo
VCC=8V, RL=45ohm,
Pin20=open
2.4
3.1
3.8
V
CTL-to-Output Transfer
Gain
Gv
Vcc=8V, RL=45ohm,
CTL=3.5V ~ 4.5V
0.6
1
1.4
V
Output offset voltage 1
Voo1
Pin9=Pin14=5V
-50
-
+50
mV
Output offset voltage 2
Voo2
Pin9=Pin14=0V
-50
-
+50
mV
Maximum output voltage
(Ta = 25
O
C, VCC1=VCC2=8V, RL=8ohm, unless otherwise specified.)
- 5 -
Nov. 2004
(Rev. 1)
www.interpionsemi.com
IP4001S
5-CH MOTOR DRIVE IC
APPLICATION SUMMARY
- All mute function using the REF pin
When the all mute function is required, you can use the reference pin as follows;
Pin 23
Mute
Above
1.0V
off
Below 1.0V
on
- All mute function using the Mute pin
All mute function can be also obtained using the MUTE pin as follows;
Pin 7
Mute
High
off
Low
on
Fig. 1. All mute function using the reference pin
Fig. 2. All mute function using the MUTE pin
Muting all channel drivers can be obtained using the
REF (signal reference) pin. The simplified schematic
diagram for reference all mute function is shown in
Fig.1. When the input voltage of the signal reference
pin (pin23) is below 1.0V, the comparator turns Q1 on
and the bias currents of all output drivers are shut
down.
As we can see in Fig. 2, if the voltage of the pin7
becomes low (below 0.5V) or open, the bias currents
for all output drivers are shut down.
On the contrary, when the voltage of the pin7 becomes
high (above 2.0V), the drivers operate normally.
VCC2
30k
30k
Q2
Q3
7
Bias currents
for output
drivers
- Thermal shutdown
Temperature
mute
Above 175
O
C
on
Falls below 150
O
C
off
Hysteresis
25
O
C
The IP4001S has a thermal protection against the
abnormal operation. When the junction temperature
rises above 175
O
C, and channel drivers are muted.
This makes the junction temperature be continuously
decreased.
When the junction temperature falls below 150
O
C, all
channel operature again.
PDF 
ZIP