2
Specifications CD54AC299/3A, CD54ACT299/3A
Absolute Maximum Ratings
DC Supply Voltage, V
CC
. . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +6V
DC Input Diode Current, I
IK
For V
I
< -0.5V or V
I
> V
CC
+ 0.5V
. . . . . . . . . . . . . . . . . . . . . .
20mA
DC Output Diode Current, I
OK
For V
O
< -0.5V or V
O
> V
CC
+ 0.5V
. . . . . . . . . . . . . . . . . . . . .
50mA
DC Output Source or Sink Current, Per Output Pin, I
O
For V
O
> -0.5V or V
O
< V
CC
+ 0.5V
. . . . . . . . . . . . . . . . . . . . .
50mA
DC V
CC
or GND Current, I
CC
or I
GND
For Up to 4 Outputs Per Device, Add
25mA For Each
Additional Output
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100mA
Power Dissipation Per Package, P
D
T
A
= -55
o
C to +100
o
C (Package F) . . . . . . . . . . . . . . . . . . 500mW
T
A
= +100
o
C to +125
o
C (Package F) . . . . . . . . Derate Linearly at
8mW/
o
C to 300mW
Operating Temperature Range, T
A
Package Type F . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to +125
o
C
Storage Temperature, T
STG
. . . . . . . . . . . . . . . . . . -65
o
C to +150
o
C
Lead Temperature (During Soldering)
At Distance 1/16in.
1/32in. (1.59mm
0.79mm)
From Case For 10s Max . . . . . . . . . . . . . . . . . . . . . . . . . . +265
o
C
Unit Inserted Into a PC Board (Min Thickness 1/16in., 1.59mm)
With Solder Contacting Lead Tips Only. . . . . . . . . . . . . . . +300
o
C
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Recommended Operating Conditions
Supply Voltage Range, V
CC
Unless Otherwise Specified, All Voltages Referenced to GND
T
A
= Full Package Temperature Range
CD54AC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5V to 5.5V
CD54ACT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V
DC Input or Output Voltage, V
I
, V
O
. . . . . . . . . . . . . . . . . . 0V to V
CC
Operating Temperature, T
A
. . . . . . . . . . . . . . . . . . . -55
o
C to +125
o
C
Input Rise and Fall Slew Rate, dt/dv
at 1.5V to 3V (AC Types) . . . . . . . . . . . . . . . . . . . 0ns/V to 50ns/V
at 3.6V to 5.5V (AC Types) . . . . . . . . . . . . . . . . . 0ns/V to 20ns/V
at 4.5V to 5.5V (AC Types) . . . . . . . . . . . . . . . . . 0ns/V to 10ns/V
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper I.C. Handling Procedures.
Copyright
Harris Corporation 1994
1
S E M I C O N D U C T O R
CD54AC299/3A
CD54ACT299/3A
8-Input Universal Shift/Storage Registers
with Common Parallel I/O Pins
2. When both S0 and S1 are HIGH, I/O terminals are in the
high-impedance state but being input ports, ready for par-
allel data to be loaded into eight registers with one clock
transition regardless of the status of OE1 and OE2.
3. Either one of the two Output Enable inputs being HIGH
will force I/O terminals to be in the off state. It is noted that
each I/O terminal is a three-state output and a CMOS
buffer input.
The CD54AC299/3A and CD54ACT299/3A are supplied in
20 lead dual-in-line ceramic packages (F suffix).
ACT INPUT LOAD TABLE
INPUT
UNIT LOAD (NOTE 1)
S1, S2, OE1, OE2
0.83
SL, CP
0.67
MR
1.33
NOTE:
1. Unit load is
I
CC
limit specified in DC Electrical Specifications
Table, e.g., 2.4mA Max at +25
o
C.
Description
The CD54AC299/3A and CD54ACT299/3A are three-state,
8-input universal shift/storage registers with common parallel
I/O pins. These devices utilize the Harris Advanced CMOS
Logic technology. These registers have four synchronous
operating modes controlled by the two select inputs as shown
in the Mode Select (S0, S1) table. The Mode Select, the Serial
Data (DS0, DS7), and the Parallel Data (I/O
0
- I/O
7
) respond
only to the LOW-to-HIGH transition of the clock pulse (CP).
S0, S1 and Data inputs must be present one setup time prior
to the positive transition of the clock.
The Master Reset (MR) is an asynchronous active-LOW
input. When MR is LOW, the register is cleared regardless of
the status of all other inputs. The register can be expanded
by cascading same units by tying the serial output (QO) to
the serial data (DS7) input of the preceding register, and
tying the serial output (Q7) to the serial data (DS0) input of
the following register. Recirculating the (n x 8) bits is accom-
plished by tying the Q7 of the last stage to the DS0 of the
first stage.
The three-state input/output (I/O) port has three modes of
operation
1. Both Output Enable (OE1 and OE2) inputs are LOW and
S0 or S1 or both are LOW, the data in the register is
present at the eight outputs.
June 1997
File Number
3907
Functional Diagram
12
2
3
9
THREE-STATE
CONTROL
18
11
10
I/O
THREE-STATE
OUTPUTS
I/O
THREE-STATE
OUTPUTS
SHIFT
REGISTER
MODE
SELECTION
7
6
5
4
8
1
20
13
14
15
16
17
19
V
CC
I/O
1
I/O
3
I/O
5
I/O
7
Q7
S1
I/O
0
I/O
2
I/O
4
I/O
6
Q0
S0
GND
DS0
DS7
MR
OE2
OE1
CP
STANDARD OUTPUT
BUS LINE
OUTPUTS
STANDARD OUTPUT
BUS LINE
OUTPUTS
COMING SOON!
COMPLETE DATA SHEET
PDF 
ZIP