4-1
Features
Switches Analog Signals Up to 20 Volts Peak-to-Peak
Each Channel Complete - Interfaces with Most
Integrated Logic
Switching Speeds Less Than 0.5
s
I
D(OFF)
Less Than 500pA Typical at 70
o
C
Effective r
DS(ON)
- 5
to 50
Commercial and Military Temperature Range
Operation
Description
The IH5009 series of analog switches were designed to fill
the need for an easy-to-use, inexpensive switch for both
industrial and military applications. Although low cost is a
primary design objective, performance and versatility have
not been sacrificed.
Each package contains up to four channels of analog gating
and is designed to eliminate the need for an external driver.
The odd numbered devices are designed to be driven
directly from TTL open collector logic (15 volts) while the
even numbered devices are driven directly from low level
TTL logic (5 volts). Each channel simulates a SPDT switch.
SPST switch action is obtained by leaving the diode cathode
unconnected; for SPDT action, the cathode should be
grounded (0V). The parts are intended for high performance
multiplexing and commutating usage. A logic "0" turns the
channel ON and a logic "1" turns the channel OFF.
Part Number Information
PART
NUMBER
CHANNELS
LOGIC
LEVEL
PACKAGE
PKG
NO.
IH5009
4
+15
DD, PD
IH5010
4
+5
DD, PD
IH5011
4
+15
DE, PE
IH5012
4
+5
DE, PE
IH5014
3
+5
DD, PD
IH5016
3
+5
DE, PE
IH5017
2
+15
PA
IH5018
2
+5
DD, PA
IH5019
2
+15
DE, PA
IH5020
2
+5
DE, PA
IH5022
1
+5
DD, PA
IH5024
1
+5
PA
NOTE: Mil-Temperature range (-55
o
C to 125
o
C) available in ceramic
packages only.
IH50XX
M
DE
PACKAGE
PA - 8 LEAD PDIP
PD - 14 LEAD PDIP
PE - 16 LEAD PDIP
DD - 14 LEAD CERDIP
DE - 16 LEAD CERDIP
TEMPERATURE RANGE
M = MILITARY (-55
o
C to 125
o
C)
C = COMMERCIAL (0
o
C to 70
o
C)
BASIC PART NUMBER
May 1999
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright
Harris Corporation 1999
IH5009-5012, 5014,
5016-5020, 5022, 5024
Virtual Ground Analog Switch
File Number
3129.1
OBSOLETE PR
ODUCT
NO RECOMMENDED REPLA
CEMENT
Call Central Applications 1-800-442-7747
or email: centapp@harris.com
4-2
Functional Diagrams
(Numbers in brackets refer to CERDIP Packages)
IH5009, IH5010
(14 LEAD CERDIP, 14 LEAD PDIP)
IH5011, IH5012
(16 LEAD CERDIP, 16 LEAD PDIP)
IH5014
(14 LEAD CERDIP, 14 LEAD PDIP)
IH5016
(16 LEAD CERDIP, 16 LEAD PDIP)
IH5017 (8 LEAD PDIP)
IH5018 (8 LEAD PDIP, 14 LEAD CERDIP)
IH5019, IH5020
(8 LEAD PDIP, 16 LEAD CERDIP)
IH5022
(8 LEAD PDIP, 14 LEAD CERDIP)
IH5024
(8 LEAD PDIP)
IH5009 Series
4-3
Absolute Maximum Ratings
Thermal Information
Positive Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
Negative Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . .-15V
Diode Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
Power Dissipation (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW
Operating Conditions
Temperature Range
5009C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0
o
C to 70
o
C
5009M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to 125
o
C
Maximum Storage Temperature Range . . . . . . . . . .-65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300
o
C
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: Dissipation rating assumes device is mounted with all leads welded or soldered to printed circuit board in ambient temperature below
75
o
C. For higher temperature, derate at rate of 5m/W
o
C.
Electrical Specifications
(Per Channel)
PARAMETER
(NOTE 1)
SYMBOL
(NOTE 4)
TEST
CONDITIONS
(NOTE 2)
TYPE
-55
o
C (M)
0
o
C (C)
MIN/MAX
25
o
C
125
o
C(M)
70
o
C (C)
MIN/MAX
UNITS
TYP
MIN/MAX
Input Current-ON
I
IN(ON)
ALL
V
IN
= 0V, I
D
= 2mA
-
0.01
0.5
100
A
Input Current-OFF
I
IN(OFF)
5V Logic Ckts
V
IN
= +4.5V,
V
A
=
10V
-
0.04
0.5
20
nA
Input Current-OFF
I
IN(OFF)
15V Logic Ckts
V
IN
= +11V,
V
A
=
10V
-
0.04
0.5
20
nA
Channel Control
Voltage-ON
V
IN(ON)
5V Logic Ckts
Note 3
0.5
-
0.5
0.5
V
Channel Control
Voltage-ON
V
IN(ON)
15V Logic Ckts
Note 3
1.5
-
1.5
1.5
V
Channel Control
Voltage-OFF
V
IN(OFF)
5V Logic Ckts
Note 3
-
-
4.5
4.5
V
Channel Control
Voltage-OFF
V
IN(OFF)
15V Logic Ckts
Note 3
-
-
11.0
11.0
V
Leakage Current-OFF
I
D(OFF)
5V Logic Ckts
V
IN
= +4.5V,
V
A
=
10V
-
0.02
0.5
20
nA
Leakage Current-OFF
I
D(OFF)
15V Logic Ckts
V
IN
= +11V,
V
A
=
10V
-
0.02
0.5
20
nA
Leakage Current-ON
I
D(ON)
5V Logic Ckts
V
IN
= 0V, I
S
= 1mA
-
0.30
1.0
1000 (M)
200 (C)
nA
Leakage Current-ON
I
D(ON)
15V Logic Ckts
V
IN
= 0V, I
S
= 1mA
-
0.10
0.5
500 (M)
100 (C)
nA
Leakage Current-ON
I
D(ON)
5V Logic Ckts
V
IN
= 0V, I
S
= 2mA
-
-
1.0
10
A
Leakage Current-ON
I
D(ON)
15V Logic Ckts
V
IN
= 0V, I
S
= 2mA
-
-
2.0
100
A
Drain-Source
ON-Resistance
r
DS(ON)
5V Logic Ckts
I
D
= 2mA, V
IN
= 0.5V
150
90
150
385 (M)
240 (C)
Drain-Source
ON-Resistance
r
DS(ON)
15V Logic Ckts
I
D
= 2mA, V
IN
= 1.5V
100
80
100
250 (M)
160 (C)
Turn-ON Time
t
(ON)
All
-
150
500
-
ns
Turn-OFF Time
t
(OFF)
All
-
300
500
-
ns
Cross Talk
CT
All
f = 100Hz
-
120
-
-
dB
NOTES:
1. (OFF) and (ON) subscript notation refers to the conduction state of the FET switch for the given test.
2. Refer to Figure 1 for definition of terms.
3. V
IN(ON)
and V
IN(OFF)
are test conditions guaranteed by the tests of r
DS(ON)
and I
D(OFF)
respectively.
4. "5V Logic CKTS" applies to even-numbered devices. "15V Logic CKTS" applies to odd-numbered devices.
IH5009 Series
PDF 
ZIP