FN3082.4

ICL7106, ICL7107, ICL7107S

Digit, LCD/LED Display, A/D

Converters

The Intersil ICL7106 and ICL7107 are high performance, low
power, 3

digit A/D converters. Included are seven

segment decoders, display drivers, a reference, and a clock.
The ICL7106 is designed to interface with a liquid crystal
display (LCD) and includes a multiplexed backplane drive;
the ICL7107 will directly drive an instrument size light
emitting diode (LED) display.

The ICL7106 and ICL7107 bring together a combination of
high accuracy, versatility, and true economy. It features auto-
zero to less than 10

V, zero drift of less than 1

C, input

bias current of 10pA (Max), and rollover error of less than
one count. True differential inputs and reference are useful in
all systems, but give the designer an uncommon advantage
when measuring load cells, strain gauges and other bridge
type transducers. Finally, the true economy of single power
supply operation (ICL7106), enables a high performance
panel meter to be built with the addition of only 10 passive
components and a display.

Features

· Guaranteed Zero Reading for 0V Input on All Scales

· True Polarity at Zero for Precise Null Detection

· 1pA Typical Input Current

· True Differential Input and Reference, Direct Display Drive

- LCD ICL7106, LED lCL7107

· Low Noise - Less Than 15

P-P

· On Chip Clock and Reference

· Low Power Dissipation - Typically Less Than 10mW

· No Additional Active Circuits Required

· Enhanced Display Stability

Ordering Information

PART NO.

TEMP.

RANGE (

PACKAGE

PKG. NO.

ICL7106CPL

0 to 70

40 Ld PDIP

E40.6

ICL7106CM44

0 to 70

44 Ld MQFP

Q44.10x10

ICL7107CPL

0 to 70

40 Ld PDIP

E40.6

ICL7107RCPL

0 to 70

40 Ld PDIP (Note)

E40.6

ICL7107SCPL

0 to 70

40 Ld PDIP (Note)

E40.6

ICL7107CM44

0 to 70

44 Ld MQFP

Q44.10x10

NOTE: "R" indicates device with reversed leads for mounting to PC
board underside. "S" indicates enhanced stability.

Data Sheet

August 2002

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143

Intersil (and design) is a registered trademark of Intersil Americas Inc.

Pinouts

ICL7106, ICL7107 (PDIP)

TOP VIEW

ICL7107R (PDIP)

TOP VIEW

ICL7106, ICL7107 (MQFP)

TOP VIEW

1
2

6
7

10
11

14
15

18
19

V+

C1
B1

B2
A2

D3
B3

(1000) AB4

POL

40
39

35
34

31
30

27
26

23
22

OSC 1
OSC 2

OSC 3

TEST

REF HI

REF LO
C

REF

COMMON

IN HI
IN LO

A-Z

BUFF

INT
V-

G2 (10's)

A3
G3

BP/GND

(1's)

(10's)

(100's)

(MINUS)

(100's)

4
5

8
9

17
18

V+

D1
C1

F1
G1

C2
B2

E2
D3

E3
(1000) AB4

POL

37
36

33
32

24
23

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V-

G2 (10's)

BP/GND

(1's)

(10's)

(100's)

(MINUS)

(100's)

OSC 2

OSC 3

TEST

2
3

10
11

12 13 14 15 16 17

OSC 1

V+

A1 F1 G1 E1 D2 C2

28
27
26

24
23

B2 A2 F2 E2 D3

AB4

POL

BP/GND

39 38 37 36 35 34

33
32
31
30
29

44 43 42 41 40

IN H

IN L

A-

BUFF

INT

V-

NC
G2
C3
A3
G3

MMON

ICL7106, ICL7107, ICL7107S

Absolute Maximum Ratings

Thermal Information

Supply Voltage

ICL7106, V+ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15V
ICL7107, V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6V
ICL7107, V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9V

Analog Input Voltage (Either Input) (Note 1) . . . . . . . . . . . . V+ to V-
Reference Input Voltage (Either Input). . . . . . . . . . . . . . . . . V+ to V-
Clock Input

ICL7106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST to V+
ICL7107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND to V+

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0

C to 70

Thermal Resistance (Typical, Note 2)

(

C/W)

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150

Maximum Storage Temperature Range . . . . . . . . . . -65

C to 150

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300

(MQFP - Lead Tips Only)

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. Input voltages may exceed the supply voltages provided the input current is limited to

100

is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications

(Note 3)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

SYSTEM PERFORMANCE

Zero Input Reading

= 0.0V, Full Scale = 200mV

-000.0

000.0

+000.0

Digital

Reading

Stability (Last Digit) (ICL7106S, ICL7107S
Only)

Fixed Input Voltage (Note 6)

-000.0

000.0

+000.0

Digital

Reading

Ratiometric Reading

= V

REF

, V

REF

= 100mV

999

999/10

1000

Digital

Reading

Rollover Error

-V

= +V

200mV

Difference in Reading for Equal Positive and Negative
Inputs Near Full Scale

0.2

Counts

Linearity

Full Scale = 200mV or Full Scale = 2V Maximum
Deviation from Best Straight Line Fit (Note 5)

0.2

Counts

Common Mode Rejection Ratio

= 1V, V

= 0V, Full Scale = 200mV (Note 5)

V/V

Noise

= 0V, Full Scale = 200mV

(Peak-To-Peak Value Not Exceeded 95% of Time)

Leakage Current Input

= 0 (Note 5)

Zero Reading Drift

= 0, 0

C To 70

C (Note 5)

0.2

Scale Factor Temperature Coefficient

= 199mV, 0

C To 70

(Ext. Ref. 0ppm/×

C) (Note 5)

ppm/

End Power Supply Character V+ Supply
Current

= 0 (Does Not Include LED Current for ICL7107)

1.0

1.8

End Power Supply Character V- Supply Current ICL7107 Only

0.6

1.8

COMMON Pin Analog Common Voltage

25k

Between Common and

Positive Supply (With Respect to + Supply)

2.4

3.0

3.2

Temperature Coefficient of Analog Common

25k

Between Common and

Positive Supply (With Respect to + Supply)

ppm/

DISPLAY DRIVER ICL7106 ONLY

Peak-To-Peak Segment Drive Voltage
Peak-To-Peak Backplane Drive Voltage

V+ = to V- = 9V (Note 4)

5.5

ICL7106, ICL7107, ICL7107S

DISPLAY DRIVER ICL7107 ONLY

Segment Sinking Current

V+ = 5V, Segment Voltage = 3V

Except Pins 19 and 20

Pin 19 Only

Pin 20 Only

NOTES:

3. Unless otherwise noted, specifications apply to both the ICL7106 and ICL7107 at T

= 25

C, f

CLOCK

= 48kHz. ICL7106 is tested in the circuit

of Figure 1. ICL7107 is tested in the circuit of Figure 2.

4. Back plane drive is in phase with segment drive for "off" segment, 180 degrees out of phase for "on" segment. Frequency is 20 times conversion

rate. Average DC component is less than 50mV.

5. Not tested, guaranteed by design.
6. Sample Tested.

Typical Applications and Test Circuits

FIGURE 1. ICL7106 TEST CIRCUIT AND TYPICAL APPLICATION WITH LCD DISPLAY COMPONENTS SELECTED FOR 200mV FULL

SCALE

FIGURE 2. ICL7107 TEST CIRCUIT AND TYPICAL APPLICATION WITH LED DISPLAY COMPONENTS SELECTED FOR 200mV FULL

SCALE

Electrical Specifications

(Note 3) (Continued)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

V+

OSC 1

OSC 2

OSC 3

TES

F LO

REF

COM

IN HI

IN LO

A-Z

BUF

INT

V-

DISPLAY

ICL7106

= 0.1

= 0.47

= 0.22

= 100pF

= 0.02

= 24k

= 47k

= 100k

= 1k

= 1M

V+

AB4

F HI

REF LO

REF

COM

A-

BUFF

INT

V-

GND

DISPLAY

ICL7107

+5V

-5V

= 0.1

= 0.47

= 0.22

= 100pF

= 0.02

= 24k

= 47k

= 100k

= 1k

= 1M

ICL7106, ICL7107, ICL7107S

Typical Integrator Amplifier Output Waveform (INT Pin)

Design Information Summary Sheet

· OSCILLATOR FREQUENCY

OSC

= 0.45/RC

OSC

> 50pF; R

OSC

> 50k

OSC

(Typ) = 48kHz

· OSCILLATOR PERIOD

OSC

= RC/0.45

· INTEGRATION CLOCK FREQUENCY

CLOCK

= f

OSC

· INTEGRATION PERIOD

INT

= 1000 x (4/f

OSC

)

· 60/50Hz REJECTION CRITERION

INT

60Hz

or t

lNT

60Hz

= Integer

· OPTIMUM INTEGRATION CURRENT

INT

= 4

· FULL SCALE ANALOG INPUT VOLTAGE

lNFS

(Typ) = 200mV or 2V

· INTEGRATE RESISTOR

· INTEGRATE CAPACITOR

· INTEGRATOR OUTPUT VOLTAGE SWING

· V

INT

MAXIMUM SWING:

(V- + 0.5V) < V

INT

< (V+ - 0.5V), V

INT

(Typ) = 2V

· DISPLAY COUNT

· CONVERSION CYCLE

CYC

= t

CL0CK

x 4000

CYC

= t

OSC

x 16,000

when f

OSC

= 48kHz; t

CYC

= 333ms

· COMMON MODE INPUT VOLTAGE

(V- + 1V) < V

< (V+ - 0.5V)

· AUTO-ZERO CAPACITOR

0.01

F < C

< 1

· REFERENCE CAPACITOR

0.1

F < C

REF

< 1

· V

COM

Biased between Vi and V-.

· V

COM

V+ - 2.8V

Regulation lost when V+ to V- <

6.8V

If V

COM

is externally pulled down to (V+ to V-)/2,

the V

COM

circuit will turn off.

· ICL7106 POWER SUPPLY: SINGLE 9V

V+ - V- = 9V
Digital supply is generated internally
V

GND

V+ - 4.5V

· ICL7106 DISPLAY: LCD

Type: Direct drive with digital logic supply amplitude.

· ICL7107 POWER SUPPLY: DUAL

5.0V

V+ = +5V to GND
V- = -5V to GND
Digital Logic and LED driver supply V+ to GND

· ICL7107 DISPLAY: LED

Type: Non-Multiplexed Common Anode

INT

INFS

INT

-----------------

INT

(

)

INT

(

)

INT

--------------------------------

INT

(

)

INT

(

)

INT

--------------------------------

COUNT

1000

REF

---------------

AUTO ZERO PHASE

(COUNTS)

2999 - 1000

SIGNAL INTEGRATE

PHASE FIXED

1000 COUNTS

DE-INTEGRATE PHASE

0 - 1999 COUNTS

TOTAL CONVERSION TIME = 4000 x t

CLOCK

= 16,000 x t

OSC

ICL7106, ICL7107, ICL7107S

Detailed Description

Analog Section

Figure 3 shows the Analog Section for the ICL7106 and
ICL7107. Each measurement cycle is divided into three
phases. They are (1) auto-zero (A-Z), (2) signal integrate
(INT) and (3) de-integrate (DE).

Auto-Zero Phase

During auto-zero three things happen. First, input high and low
are disconnected from the pins and internally shorted to analog
COMMON. Second, the reference capacitor is charged to the
reference voltage. Third, a feedback loop is closed around the
system to charge the auto-zero capacitor C

to compensate

for offset voltages in the buffer amplifier, integrator, and
comparator. Since the comparator is included in the loop, the A-
Z accuracy is limited only by the noise of the system. In any
case, the offset referred to the input is less than 10

Signal Integrate Phase

During signal integrate, the auto-zero loop is opened, the
internal short is removed, and the internal input high and low
are connected to the external pins. The converter then
integrates the differential voltage between IN HI and IN LO for a
fixed time. This differential voltage can be within a wide
common mode range: up to 1V from either supply. If, on the
other hand, the input signal has no return with respect to the
converter power supply, IN LO can be tied to analog COMMON
to establish the correct common mode voltage. At the end of
this phase, the polarity of the integrated signal is determined.

De-Integrate Phase

The final phase is de-integrate, or reference integrate. Input
low is internally connected to analog COMMON and input
high is connected across the previously charged reference
capacitor. Circuitry within the chip ensures that the capacitor
will be connected with the correct polarity to cause the
integrator output to return to zero. The time required for the
output to return to zero is proportional to the input signal.
Specifically the digital reading displayed is:

Differential Input

The input can accept differential voltages anywhere within the
common mode range of the input amplifier, or specifically from
0.5V below the positive supply to 1V above the negative
supply. In this range, the system has a CMRR of 86dB typical.
However, care must be exercised to assure the integrator
output does not saturate. A worst case condition would be a
large positive common mode voltage with a near full scale
negative differential input voltage. The negative input signal
drives the integrator positive when most of its swing has been
used up by the positive common mode voltage. For these
critical applications the integrator output swing can be

reduced to less than the recommended 2V full scale swing
with little loss of accuracy. The integrator output can swing to
within 0.3V of either supply without loss of linearity.

Differential Reference

The reference voltage can be generated anywhere within the
power supply voltage of the converter. The main source of
common mode error is a roll-over voltage caused by the
reference capacitor losing or gaining charge to stray capacity
on its nodes. If there is a large common mode voltage, the
reference capacitor can gain charge (increase voltage) when
called up to de-integrate a positive signal but lose charge
(decrease voltage) when called up to de-integrate a negative
input signal. This difference in reference for positive or negative
input voltage will give a roll-over error. However, by selecting
the reference capacitor such that it is large enough in
comparison to the stray capacitance, this error can be held to
less than 0.5 count worst case. (See Component Value
Selection.)

DISPLAY COUNT = 1000

REF

---------------

ICL7106, ICL7107, ICL7107S

Analog COMMON

This pin is included primarily to set the common mode
voltage for battery operation (ICL7106) or for any system
where the input signals are floating with respect to the power
supply. The COMMON pin sets a voltage that is
approximately 2.8V more negative than the positive supply.
This is selected to give a minimum end-of-life battery voltage
of about 6V. However, analog COMMON has some of the
attributes of a reference voltage. When the total supply
voltage is large enough to cause the zener to regulate (>7V),
the COMMON voltage will have a low voltage coefficient
(0.001%/V), low output impedance (

), and a

temperature coefficient typically less than 80ppm/×

The limitations of the on chip reference should also be
recognized, however. With the ICL7107, the internal heating
which results from the LED drivers can cause some
degradation in performance. Due to their higher thermal
resistance, plastic parts are poorer in this respect than
ceramic. The combination of reference Temperature
Coefficient (TC), internal chip dissipation, and package
thermal resistance can increase noise near full scale from
25

V to 80

P-P

. Also the linearity in going from a high

dissipation count such as 1000 (20 segments on) to a low
dissipation count such as 1111(8 segments on) can suffer by a
count or more. Devices with a positive TC reference may
require several counts to pull out of an over-range condition.
This is because over-range is a low dissipation mode, with the
three least significant digits blanked. Similarly, units with a
negative TC may cycle between over-range and a non-over-
range count as the die alternately heats and cools. All these
problems are of course eliminated if an external reference is
used.

The ICL7106, with its negligible dissipation, suffers from
none of these problems. In either case, an external
reference can easily be added, as shown in Figure 4.

Analog COMMON is also used as the input low return during
auto-zero and de-integrate. If IN LO is different from analog
COMMON, a common mode voltage exists in the system
and is taken care of by the excellent CMRR of the converter.
However, in some applications IN LO will be set at a fixed
known voltage (power supply common for instance). In this
application, analog COMMON should be tied to the same
point, thus removing the common mode voltage from the
converter. The same holds true for the reference voltage. If
reference can be conveniently tied to analog COMMON, it
should be since this removes the common mode voltage
from the reference system.

Within the lC, analog COMMON is tied to an N-Channel FET
that can sink approximately 30mA of current to hold the
voltage 2.8V below the positive supply (when a load is trying
to pull the common line positive). However, there is only
10

A of source current, so COMMON may easily be tied to a

more negative voltage thus overriding the internal reference.

FIGURE 3. ANALOG SECTION OF ICL7106 AND ICL7107

DE+

INT

BUFFER

A-Z

INT

A-Z

COMPARATOR

IN HI

COMMON

IN LO

DE-

DE+

INT

A-Z

REF

REF HI

REF

REF LO

A-Z

REF

DIGITAL

SECTION

A-Z AND DE

(±)

INTEGRATOR

INT

STRAY

V+

V-

INPUT

HIGH

2.8V

6.2V

V+

INPUT

LOW

FIGURE 4A.

ICL7106

REF LO

ICL7107

REF HI

V+

V-

6.8V

ZENER

ICL7106, ICL7107, ICL7107S

TEST

The TEST pin serves two functions. On the ICL7106 it is
coupled to the internally generated digital supply through a
500

resistor. Thus it can be used as the negative supply for

externally generated segment drivers such as decimal points
or any other presentation the user may want to include on
the LCD display. Figures 5 and 6 show such an application.
No more than a 1mA load should be applied.

The second function is a "lamp test". When TEST is pulled
high (to V+) all segments will be turned on and the display
should read "1888". The TEST pin will sink about 15mA
under these conditions.

CAUTION: In the lamp test mode, the segments have a constant DC
voltage (no square-wave). This may burn the LCD display if main-
tained for extended periods.

Digital Section

Figures 7 and 8 show the digital section for the ICL7106 and
ICL7107, respectively. In the ICL7106, an internal digital
ground is generated from a 6V Zener diode and a large
P-Channel source follower. This supply is made stiff to
absorb the relative large capacitive currents when the back
plane (BP) voltage is switched. The BP frequency is the
clock frequency divided by 800. For three readings/sec., this
is a 60Hz square wave with a nominal amplitude of 5V. The
segments are driven at the same frequency and amplitude
and are in phase with BP when OFF, but out of phase when
ON. In all cases negligible DC voltage exists across the
segments.

Figure 8 is the Digital Section of the ICL7107. It is identical to
the ICL7106 except that the regulated supply and back
plane drive have been eliminated and the segment drive has
been increased from 2mA to 8mA, typical for instrument size
common anode LED displays. Since the 1000 output (pin
19) must sink current from two LED segments, it has twice
the drive capability or 16mA.

In both devices, the polarity indication is "on" for negative
analog inputs. If IN LO and IN HI are reversed, this indication
can be reversed also, if desired.

FIGURE 4B.

FIGURE 4. USING AN EXTERNAL REFERENCE

ICL7106

REF HI

REF LO

COMMON

V+

ICL8069

1.2V

REFERENCE

6.8k

20k

ICL7107

ICL7106

V+

TEST

TO LCD

BACKPLANE

TO LCD

DECIMAL

POINT

FIGURE 5. SIMPLE INVERTER FOR FIXED DECIMAL POINT

ICL7106

V+

TEST

DECIMAL

POINT

SELECT

CD4030

GND

V+

TO LCD

DECIMAL

POINTS

FIGURE 6. EXCLUSIVE `OR' GATE FOR DECIMAL POINT DRIVE

ICL7106, ICL7107, ICL7107S

System Timing

Figure 9 shows the clocking arrangement used in the
ICL7106 and ICL7107. Two basic clocking arrangements
can be used:

1. Figure 9A. An external oscillator connected to pin 40.
2. Figure 9B. An R-C oscillator using all three pins.

The oscillator frequency is divided by four before it clocks
the decade counters. It is then further divided to form the
three convert-cycle phases. These are signal integrate
(1000 counts), reference de-integrate (0 to 2000 counts) and
auto-zero (1000 to 3000 counts). For signals less than full
scale, auto-zero gets the unused portion of reference
de-integrate. This makes a complete measure cycle of 4,000
counts (16,000 clock pulses) independent of input voltage.
For three readings/second, an oscillator frequency of 48kHz
would be used.

To achieve maximum rejection of 60Hz pickup, the signal
integrate cycle should be a multiple of 60Hz. Oscillator
frequencies of 240kHz, 120kHz, 80kHz, 60kHz, 48kHz,
40kHz, 33

kHz, etc. should be selected. For 50Hz

rejection, Oscillator frequencies of 200kHz, 100kHz,
66

kHz, 50kHz, 40kHz, etc. would be suitable. Note that

40kHz (2.5 readings/second) will reject both 50Hz and 60Hz
(also 400Hz and 440Hz).

SEGMENT

DECODE

SEGMENT

0.5mA

8mA

DIGITAL GROUND

TYPICAL SEGMENT OUTPUT

V+

LATCH

SEGMENT

DECODE

LOGIC CONTROL

SEGMENT

DECODE

1000's

100's

10's

1's

TO SWITCH DRIVERS

FROM COMPARATOR OUTPUT

DIGITAL

GROUND

CLOCK

OSC 1

OSC 2

OSC 3

V+
TEST

500

COUNTER

V+

THREE INVERTERS

ONE INVERTER SHOWN FOR CLARITY

FIGURE 8. ICL7107 DIGITAL SECTION

CLOCK

INTERNAL TO PART

GND ICL7107

CLOCK

INTERNAL TO PART

RC OSCILLATOR

TEST ICL7106

FIGURE 9B.

FIGURE 9. CLOCK CIRCUITS

FIGURE 9A.

ICL7106, ICL7107, ICL7107S

Component Value Selection

Integrating Resistor

Both the buffer amplifier and the integrator have a class A
output stage with 100

A of quiescent current. They can

supply 4

A of drive current with negligible nonlinearity. The

integrating resistor should be large enough to remain in this
very linear region over the input voltage range, but small
enough that undue leakage requirements are not placed on
the PC board. For 2V full scale, 470k

is near optimum and

similarly a 47k

for a 200mV scale.

Integrating Capacitor

The integrating capacitor should be selected to give the
maximum voltage swing that ensures tolerance buildup will
not saturate the integrator swing (approximately. 0.3V from
either supply). In the ICL7106 or the ICL7107, when the
analog COMMON is used as a reference, a nominal +2V full-
scale integrator swing is fine. For the ICL7107 with +5V
supplies and analog COMMON tied to supply ground, a

3.5V to +4V swing is nominal. For three readings/second

(48kHz clock) nominal values for C

lNT

are 0.22

F and

0.10

F, respectively. Of course, if different oscillator

frequencies are used, these values should be changed in
inverse proportion to maintain the same output swing.

An additional requirement of the integrating capacitor is that
it must have a low dielectric absorption to prevent roll-over
errors. While other types of capacitors are adequate for this
application, polypropylene capacitors give undetectable
errors at reasonable cost.

Auto-Zero Capacitor

The size of the auto-zero capacitor has some influence on
the noise of the system. For 200mV full scale where noise is
very important, a 0.47

F capacitor is recommended. On the

2V scale, a 0.047

F capacitor increases the speed of

recovery from overload and is adequate for noise on this
scale.

Reference Capacitor

A 0.1

F capacitor gives good results in most applications.

However, where a large common mode voltage exists (i.e.,
the REF LO pin is not at analog COMMON) and a 200mV
scale is used, a larger value is required to prevent roll-over
error. Generally 1

F will hold the roll-over error to 0.5 count

in this instance.

Oscillator Components

For all ranges of frequency a 100k

resistor is recommended

and the capacitor is selected from the equation:

Reference Voltage

The analog input required to generate full scale output (2000
counts) is: V

= 2V

REF

. Thus, for the 200mV and 2V scale,

REF

should equal 100mV and 1V, respectively. However, in

many applications where the A/D is connected to a
transducer, there will exist a scale factor other than unity
between the input voltage and the digital reading. For
instance, in a weighing system, the designer might like to
have a full scale reading when the voltage from the
transducer is 0.662V. Instead of dividing the input down to
200mV, the designer should use the input voltage directly
and select V

REF

= 0.341V. Suitable values for integrating

resistor and capacitor would be 120k

and 0.22

F. This

makes the system slightly quieter and also avoids a divider
network on the input. The ICL7107 with

5V supplies can

accept input signals up to

4V. Another advantage of this

system occurs when a digital reading of zero is desired for
V

0. Temperature and weighing systems with a variable

fare are examples. This offset reading can be conveniently
generated by connecting the voltage transducer between IN
HI and COMMON and the variable (or fixed) offset voltage
between COMMON and IN LO.

ICL7107 Power Supplies

The ICL7107 is designed to work from

5V supplies.

However, if a negative supply is not available, it can be
generated from the clock output with 2 diodes, 2 capacitors,
and an inexpensive lC. Figure 10 shows this application.
See ICL7660 data sheet for an alternative.

In fact, in selected applications no negative supply is
required. The conditions to use a single +5V supply are:

1. The input signal can be referenced to the center of the

common mode range of the converter.

2. The signal is less than

1.5V.

3. An external reference is used.

0.45

----------- For 48kHz Clock (3 Readings/sec),

100pF.

ICL7107

V+

OSC 1

V-

OSC 2

OSC 3

GND

V+

V- = 3.3V

0.047

1N914

CD4009

FIGURE 10. GENERATING NEGATIVE SUPPLY FROM +5V

ICL7106, ICL7107, ICL7107S

Typical Applications

The ICL7106 and ICL7107 may be used in a wide variety of
configurations. The circuits which follow show some of the
possibilities, and serve to illustrate the exceptional versatility
of these A/D converters.

The following application notes contain very useful
information on understanding and applying this part and are
available from Intersil Corporation.

Application Notes

NOTE #

DESCRIPTION

AN016

"Selecting A/D Converters"

AN017

"The Integrating A/D Converter"

AN018

"Do's and Don'ts of Applying A/D Converters"

AN023

"Low Cost Digital Panel Meter Designs"

AN032

"Understanding the Auto-Zero and Common Mode
Performance of the ICL7136/7/9 Family"

AN046

"Building a Battery-Operated Auto Ranging DVM with the
ICL7106"

AN052

"Tips for Using Single Chip 3

Digit A/D Converters"

AN9609 "Overcoming Common Mode Range Issues When Using

Intersil Integrating Converters"

Typical Applications

FIGURE 11. ICL7106 USING THE INTERNAL REFERENCE

FIGURE 12. ICL7107 USING THE INTERNAL REFERENCE

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

100pF

TO PIN 1

SET V

REF

= 100mV

0.1

0.01

100k

22k

47k

0.22

0.47

TO BACKPLANE

TO DISPLAY

Values shown are for 200mV full scale, 3 readings/sec., floating
supply voltage (9V battery).

Values shown are for 200mV full scale, 3 readings/sec. IN LO may
be tied to either COMMON for inputs floating with respect to
supplies, or GND for single ended inputs. (See discussion under
Analog COMMON).

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

GND

100pF

TO PIN 1

SET V

REF

= 100mV

0.1

0.01

100k

22k

47k

0.22

0.47

TO DISPLAY

+5V

-5V

ICL7106, ICL7107, ICL7107S

FIGURE 13. ICL7107 WITH AN EXTERNAL BAND-GAP

REFERENCE (1.2V TYPE)

FIGURE 14. ICL7107 WITH ZENER DIODE REFERENCE

FIGURE 15. ICL7106 AND ICL7107: RECOMMENDED

COMPONENT VALUES FOR 2V FULL SCALE

FIGURE 16. ICL7107 OPERATED FROM SINGLE +5V

Typical Applications

(Continued)

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

GND

100pF

TO PIN 1

SET V

REF

= 100mV

0.1

0.01

100k

10k

47k

0.47

TO DISPLAY

IN LO is tied to supply COMMON establishing the correct common mode
voltage. If COMMON is not shorted to GND, the input voltage may float
with respect to the power supply and COMMON acts as a pre-regulator
for the reference. If COMMON is shorted to GND, the input is single
ended (referred to supply GND) and the pre-regulator is overridden.

10k

1.2V (ICL8069)

0.22

Since low TC zeners have breakdown voltages ~ 6.8V, diode must
be placed across the total supply (10V). As in the case of Figure 12,
IN LO may be tied to either COMMON or GND.

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

GND

100pF

TO PIN 1

SET V

REF

= 100mV

0.1

0.01

100k

47k

0.22

0.47

TO DISPLAY

+5V

-5V

6.8V

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

BP/GND

100pF

TO PIN 1

SET V

REF

= 1V

0.1

0.01

100k

25k

24k

470k

0.22

0.047

TO DISPLAY

V+

V-

40
39
38
37
36
35
34
33
32
31
30
29

27
26
25
24
23
22
21

OSC 1
OSC 2
OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

C3
A3

GND

100pF

TO PIN 1

SET V

REF

= 100mV

0.1

0.01

100k

10k

47k

0.22

0.47

TO DISPLAY

An external reference must be used in this application, since the
voltage between V+ and V- is insufficient for correct operation of the
internal reference.

15k

1.2V (ICL8069)

+5V

ICL7106, ICL7107, ICL7107S

FIGURE 17. ICL7107 MEASUREING RATIOMETRIC VALUES

OF QUAD LOAD CELL

FIGURE 18. ICL7106 USED AS A DIGITAL CENTIGRADE

THERMOMETER

FIGURE 19. CIRCUIT FOR DEVELOPING UNDERRANGE AND

OVERRANGE SIGNAL FROM ICL7106 OUTPUTS

FIGURE 20. CIRCUIT FOR DEVELOPING UNDERRANGE AND

OVERRANGE SIGNALS FROM ICL7107 OUTPUT

Typical Applications

(Continued)

40
39
38
37
36
35
34
33
32
31
30
29

27
26
25
24
23
22
21

OSC 1
OSC 2
OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

C3
A3

GND

100pF

TO PIN 1

0.1

100k

0.47

TO DISPLAY

The resistor values within the bridge are determined by the desired
sensitivity.

V+

0.22

47k

40
39
38
37
36
35
34
33
32
31
30
29

27
26
25
24
23
22
21

OSC 1
OSC 2
OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V -

C3
A3

100pF

TO PIN 1

0.1

0.01

100k

47k

0.22

0.47

TO BACKPLANE

TO DISPLAY

A silicon diode-connected transistor has a temperature coefficient of
about -2mV/

C. Calibration is achieved by placing the sensing

transistor in ice water and adjusting the zeroing potentiometer for a
000.0 reading. The sensor should then be placed in boiling water
and the scale-factor potentiometer adjusted for a 100.0 reading.

SCALE

FACTOR

ADJUST

100k

220k

22k

SILICON NPN

MPS 3704 OR

SIMILAR

ZERO

ADJUST

V+

AB4

POL

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V-

O/RANGE

U/RANGE

CD4023 OR

74C10

CD4077

TO LOGIC

V+

LOGIC

V-

GND

O/RANGE

U/RANGE

CD4023 OR

74C10

TO LOGIC

+5V

V-

33k

The LM339 is required to
ensure logic compatibility
with heavy display loading.

V+

AB4

POL

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

V-

12k

LM339

ICL7106, ICL7107, ICL7107S

FIGURE 21. AC TO DC CONVERTER WITH ICL7106

FIGURE 22. DISPLAY BUFFERING FOR INCREASED DRIVE CURRENT

Typical Applications

(Continued)

OSC 1

OSC 2

OSC 3

TEST

REF HI

REF LO

REF

COMMON

IN HI

IN LO

A-Z

BUFF

INT

100pF

TO PIN 1

0.1

100k

22k

47k

0.22

0.47

TO BACKPLANE

TO DISPLAY

Test is used as a common-mode reference level to ensure compatibility with most op amps.

470k

4.3k

100pF

(FOR OPTIMUM BANDWIDTH)

10k

1N914

0.22

CA3140

2.2M

100k

AC IN

SCALE FACTOR ADJUST

REF

= 100mV FOR AC TO RMS)

ICL7107

130

LED

SEGMENTS

+5V

DM7407

ICL7106, ICL7107, ICL7107S

ICL7106, ICL7107, ICL7107S

Dual-In-Line Plastic Packages (PDIP)

NOTES:

1. Controlling Dimensions: INCH. In case of conflict between English

and Metric dimensions, the inch dimensions control.

2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the "MO Series Symbol List" in Section 2.2

of Publication No. 95.

4. Dimensions A, A1 and L are measured with the package seated in

JEDEC seating plane gauge GS-3.

5. D, D1, and E1 dimensions do not include mold flash or protrusions.

Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).

6. E and

are measured with the leads constrained to be per-

pendicular to datum

7. e

and e

are measured at the lead tips with the leads uncon-

strained. e

must be zero or greater.

8. B1 maximum dimensions do not include dambar protrusions. Dam-

bar protrusions shall not exceed 0.010 inch (0.25mm).

9. N is the maximum number of terminal positions.

10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,

E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).

-C-

-B-

INDEX

1 2 3

N/2

AREA

SEATING

BASE

PLANE

-C-

-A-

0.010 (0.25)

C A

B S

E40.6

(JEDEC MS-011-AC ISSUE B)

40 LEAD DUAL-IN-LINE PLASTIC PACKAGE

SYMBOL

INCHES

MILLIMETERS

NOTES

MIN

MAX

MIN

MAX

0.250

6.35

0.015

0.39

0.125

0.195

3.18

4.95

0.014

0.022

0.356

0.558

0.030

0.070

0.77

1.77

0.008

0.015

0.204

0.381

1.980

2.095

50.3

53.2

0.005

0.13

0.600

0.625

15.24

15.87

0.485

0.580

12.32

14.73

0.100 BSC

2.54 BSC

0.600 BSC

15.24 BSC

0.700

17.78

0.115

0.200

2.93

5.08

Rev. 0 12/93

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.

Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

ICL7106, ICL7107, ICL7107S

Metric Plastic Quad Flatpack Packages (MQFP)

E E1

-A-

PIN 1

A2 A1

-16

-7

0.40

0.016 MIN

MIN

PLANE

0.005/0.009

0.13/0.23

WITH PLATING

BASE METAL

SEATING

0.005/0.007

0.13/0.17

-B-

0.008

0.20

A-B

0.076

0.003

-C-

-D-

-H-

Q44.10x10

(JEDEC MS-022AB ISSUE B)

44 LEAD METRIC PLASTIC QUAD FLATPACK PACKAGE

SYMBOL

INCHES

MILLIMETERS

NOTES

MIN

MAX

MIN

MAX

0.096

2.45

0.004

0.010

0.10

0.25

0.077

0.083

1.95

2.10

0.012

0.018

0.30

0.45

0.012

0.016

0.30

0.40

0.515

0.524

13.08

13.32

0.389

0.399

9.88

10.12

4, 5

0.516

0.523

13.10

13.30

0.390

0.398

9.90

10.10

4, 5

0.029

0.040

0.73

1.03

0.032 BSC

0.80 BSC

Rev. 2 4/99

NOTES:

1. Controlling dimension: MILLIMETER. Converted inch

dimensions are not necessarily exact.

2. All dimensions and tolerances per ANSI Y14.5M-1982.
3. Dimensions D and E to be determined at seating plane

4. Dimensions D1 and E1 to be determined at datum plane

5. Dimensions D1 and E1 do not include mold protrusion.

Allowable protrusion is 0.25mm (0.010 inch) per side.

6. Dimension b does not include dambar protrusion. Allowable

dambar protrusion shall be 0.08mm (0.003 inch) total.

7. "N" is the number of terminal positions.

-C-

-H-

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: ICL7106S

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: ICL7106S