Data SheetNo. PD60190-C
INTEGRATED SWITCHER
Descriptions
The IRIS4015(K) is a dual mode voltage and current controller combined with a MOSFET in a single package.
The IRIS4015(K) is designed for use in AC/DC switching power supplies up to 230VAC nominal input, and is
capable of 180W for a universal line input. The device operates on a quasi-resonant or Pulse Ratio Control (PRC)
basis, and thereby variable frequency operation.
www.irf.com
1
Features
Primary current mode control, and secondary
voltage mode control
Vcc Over-voltage protection (latched)
Over-current & over-temperature protection
Quasi resonant, variable frequency operation
5 pin TO-220 and TO-262 package
0.97
Rds(on) max/ 650V MOSFET
Fully Characterized Avalanche Energy
IRIS4015(K)
Typical Connection Diagram
IRIS4015(K)
3
1
2
4
5
Drain
Source
Vcc
FB
Gnd
Vout
(DC)
Vin
(AC/
DC)
(Refer to Lead Assignments for correct pin
configuration). This/These diagram(s) show electrical
connections only. Please refer to our DesignTips
and Application Notes (AN1018a, AN1024a,
AN1025) for proper circuit board layout.
Packages
IRIS4015K
5 Lead TO-262
IRIS4015
5 Lead TO-220
2
IRIS4015(K)
www.irf.com
Symbol
Definition
Terminals
Max. Ratings
Units
Note
I
D
peak
Peak drain current
3-1
21
Single pulse
I
D
max
Maximum switching current
3-1
8
V2-3 = 0.78V
Ta=-20 - +125
o
C
E
AS
Single pulse avalanche energy
3-1
325
mJ
single pulse
I
L
peak=5.7A
V
CC
Power supply voltage
4-3
35
V
TH
OCP/FB terminal voltage
5-2
6
P
D1
Power dissipation for MOSFET
235
With infinite heatsink
1.2
Without heatsink
P
D2
Power dissipation for control part (MIC)
4-2
0.8
Rth
JC
Thermal resistance, junction to case
--
0.53
C/W
T
J
Junction temperature
--
-40-125
T
S
Storage temperature
--
-40-125
T
f
Internal frame temperature in operation
--
-20-125
Refer to recommended
operating temperature
T
OP
Ambient operating temperature
--
-20-125
T
L
Lead temp. (soldering, 10 seconds)
--
300
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are
absolute voltages referenced to terminals stated, all currents are defined positive into any lead. The thermal resistance and
power dissipation ratings are measured under board mounted and still air conditions.
Recommended Operating Conditions
Time for input of quasi resonant signals.
For the Quasi resonant signal inputted to the V
OCP/FB
terminal at the time of quasi resonant operation, the
signal should be wider thant Tth(2)
Specified by V
IN
x I
IN
V
3-1
A
C
Tth(2) s
1.0
Vth(2)
V
OCP/FB
W
www.irf.com
3
IRIS4015(K)
Electrical Characteristics (for Control Part (MIC))
V
CC
= 18V, (T
A
= 25C) unless otherwise specified.
Symbol
Definition
Min. Typ. Max. Units Test Conditions
V
CCUV+
V
CC
supply undervoltage positive going threshold
14.4
16
17.6
V
CCHYS
V
CC
supply undervoltage lockout hysteresis
5.4
6.0
6.6
I
QCCUV
UVLO mode quiescent current
--
--
100
A
V
CC <
V
CCUV-
I
QCC
Quiescent operating V
CC
supply current
--
--
30
mA
T
OFF(MAX)
Maximum OFF time
40
--
60
T
TH(2)
Minimum input pulse width for quasi resonant signals
--
--
1.0
T
OFF(MIN)
Minimum OFF time
--
--
1.5
V
TH(1)
OCP/FB terminal threshold voltage 1
0.68
0.73
0.78
V
TH(2)
OCP/FB terminal threshold voltage 2
1.3
1.45
1.6
I
OCP/FB
OCP/FB terminal sink current
1.1
1.35
1.7
mA
V
CC(OVP)
V
CC
overvoltage protection limit
20.5
22.5
24.5
V
I
IN(H)
Latch circuit sustaining current
--
--
400
A
V
IN(LaOFF)
Latch circuit reset voltage
6.6
--
8.4
V
T
J(TSD)
Thermal shutdown activation temperature
140
--
--
o
C
V
sec
V
Electrical Characteristics (for MOSFET)
(T
A
= 25C) unless otherwise specified.
Symbol
Definition
Min. Typ. Max. Units Test Conditions
V
DSS
Drain-to-source breakdown voltage
650
--
--
V
I
DSS
Drain leakage current
--
--
25
A
Vds=650V,
V
GS
=0V
R
DS(ON)
On-resistance
--
--
0.97
V
3-1
=10V, I
D
=8.8A
tr
Rise time (10% to 90%)
--
--
310
ns
THj-C
Thermal resistance
--
--
0.53
o
C/W
Between junction
and case
4
IRIS4015(K)
www.irf.com
Block Diagram
Pin # S y m b o l
Description
1
3
5
4
2
D
O C P / F B
V c c
G r o u n d
S
M O S F E T D r a i n t e r m i n a l
M O S F E T S o u r c e t e r m i n a l
Ground terminal
Control circuit supply voltage
Overcurrent detection, and Voltage mode control
feedback signal
L e a d A s s i g n m e n t s
5
4
3
2
1
Other Functions
O.V.P. Overvoltage Protection Circuit
T.S.D. Thermal Shutdown Circuit
5/4/2001
+
-
DRIVE
OSCILLATOR
+
-
LATCH
O.V.P
START
REG.
T.S.D
4
Vcc
3
Ground
5
OCP/
FB
2
S
1
D
Vth(1)
Vth(2)
Comp.1
Comp.2
www.irf.com
5
IRIS4015(K)
5-Lead TO-220
Case outline
01-6020 00
01-3042 01
(TS-001)
6
IRIS4015(K)
www.irf.com
IR WORLD HEADQUARTERS: 233 Kansas Street, El Segundo, California 90245 Tel: (310) 252-7105
Data and specifications subject to change without notice. 5/27/2002
1
6
10.29 [.405]
9.65 [.380]
1.40 [.055]
MAX.
2 3 4 5
0.25 [.010]
A
B
4X
1.70 [.067]
5X
5X
4.83 [.190]
4.06 [.160]
B
6
1.32 [.052]
1.22 [.048]
C
9.65 [.380]
8.64 [.340]
12.70 [.500]
14.73 [.580]
1.01[.040]
0.51[.020]
2.92 [.115]
2.16 [.085]
0.63 [.025]
0.31 [.012]
6.22[.245]
MIN
8.00[.315]
MAX
5-Lead TO-262
Case outline
PDF 
ZIP