ChipFind - документация

Электронный компонент: IS61LV3216L-20TI

Скачать:  PDF   ZIP
FEATURES
High-speed access time: 10, 12, 15, and 20 ns
CMOS low power operation
-- 130 mW (typical) operating
-- 150 W (typical) standby
TTL compatible interface levels
Single 3.3V + 10%, 5% power supply for 10
and 12 ns
Single 3.3V 10% power supply for 15
and 20 ns
Fully static operation: no clock or refresh
required
Three state outputs
Industrial temperature available
Available in 44-pin 400-mil SOJ package and
44-pin TSOP (Type II)
IS61LV3216L
32K x 16 LOW VOLTAGE CMOS STATIC RAM
DESCRIPTION
The
ISSI
IS61LV3216L is a high-speed, 512K static RAM
organized as 32,768 words by 16 bits. It is fabricated using
ISSI
's high-performance CMOS technology. This highly reli-
able process coupled with innovative circuit design tech-
niques, yields fast access times with low power consumption.
When
CE is HIGH (deselected), the device assumes a standby
mode at which the power dissipation can be reduced down to
150 W (typical) with CMOS input levels.
Easy memory expansion is provided by using Chip Enable
and Output Enable inputs,
CE and OE. The active LOW Write
Enable (
WE) controls both writing and reading of the memory.A
data byte allows Upper Byte (
UB) and Lower Byte (LB) access.
The IS61LV3216L is packaged in the JEDEC standard 44-pin
400-mil SOJ and 44-pin TSOP (Type II).
FUNCTIONAL BLOCK DIAGRAM
DECEMBER 2000
ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any
errors which may appear in this publication. Copyright 2000, Integrated Silicon Solution, Inc.
A0-A14
CE
OE
WE
32K x 16
MEMORY ARRAY
DECODER
COLUMN I/O
CONTROL
CIRCUIT
GND
VCC
I/O
DATA
CIRCUIT
I/O0-I/O7
Lower Byte
I/O8-I/O15
Upper Byte
UB
LB
ISSI
Integrated Silicon Solution, Inc. -- 1-800-379-4774
1
Rev. A
12/19/00
IS61LV3216L
ISSI
2
Integrated Silicon Solution, Inc. -- 1-800-379-4774
Rev. A
12/19/00
PIN CONFIGURATIONS
44-Pin SOJ
PIN DESCRIPTIONS
A0-A14
Address Inputs
I/O0-I/O15
Data Inputs/Outputs
CE
Chip Enable Input
OE
Output Enable Input
WE
Write Enable Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
NC
A14
A13
A12
A11
CE
I/O0
I/O1
I/O2
I/O3
Vcc
GND
I/O4
I/O5
I/O6
I/O7
WE
A10
A9
A8
A7
NC
A0
A1
A2
OE
UB
LB
I/O15
I/O14
I/O13
I/O12
GND
Vcc
I/O11
I/O10
I/O9
I/O8
NC
A3
A4
A5
A6
NC
TRUTH TABLE
I/O PIN
Mode
WE
CE
OE
LB
UB
I/O0-I/O7
I/O8-I/O15
Vcc Current
Not Selected
X
H
X
X
X
High-Z
High-Z
I
SB
1
, I
SB
2
Output Disabled
H
L
H
X
X
High-Z
High-Z
I
CC
X
L
X
H
H
High-Z
High-Z
Read
H
L
L
L
H
D
OUT
High-Z
I
CC
H
L
L
H
L
High-Z
D
OUT
H
L
L
L
L
D
OUT
D
OUT
Write
L
L
X
L
H
D
IN
High-Z
I
CC
L
L
X
H
L
High-Z
D
IN
L
L
X
L
L
D
IN
D
IN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
NC
A14
A13
A12
A11
CE
I/O0
I/O1
I/O2
I/O3
Vcc
GND
I/O4
I/O5
I/O6
I/O7
WE
A10
A9
A8
A7
NC
A0
A1
A2
OE
UB
LB
I/O15
I/O14
I/O13
I/O12
GND
Vcc
I/O11
I/O10
I/O9
I/O8
NC
A3
A4
A5
A6
NC
44-Pin TSOP (TYPE II)
LB
Lower-byte Control (I/O0-I/O7)
UB
Upper-byte Control (I/O8-I/O15)
NC
No Connection
Vcc
Power
GND
Ground
IS61LV3216L
1
2
3
4
5
6
7
8
9
10
11
12
ISSI
Integrated Silicon Solution, Inc. -- 1-800-379-4774
3
Rev. A
12/19/00
OPERATING RANGE
Range
Ambient Temperature
V
CC
10 ns, 12 ns
V
CC
15 ns, 20 ns
Commercial
0C to + 70C
3.3V +10%, 5%
3.3V 10%
Industrial
40C to + 85C
3.3V +10%, 5%
3.3V 10%
POWER SUPPLY CHARACTERISTICS
(1)
(Over Operating Range)
-10 ns
-12 ns
-15 ns
-20 ns
Symbol Parameter
Test Conditions
Min. Max.
Min. Max.
Min. Max.
Min. Max.
Unit
I
CC
Vcc Dynamic Operating
V
CC
= Max.,
Com.
--
130
--
120
--
110
--
100
mA
Supply Current
I
OUT
= 0 mA, f = f
MAX
Ind.
--
--
--
130
--
120
--
110
I
SB
1
TTL Standby Current
V
CC
= Max.,
Com.
--
10
--
10
--
10
--
10
mA
(TTL Inputs)
V
IN
= V
IH
or V
IL
Ind.
--
--
--
10
--
10
--
10
CE V
IH
, f = 0
I
SB
2
CMOS Standby
V
CC
= Max.,
Com.
--
1
--
1
--
1
--
1
mA
Current (CMOS Inputs)
CE V
CC
0.2V,
Ind.
--
--
--
1
--
1
--
1
V
IN
V
CC
0.2V, or
V
IN
- 0.2V, f = 0
Note:
1. At f = f
MAX
, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
DC ELECTRICAL CHARACTERISTICS
(Over Operating Range)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
V
OH
Output HIGH Voltage
V
CC
= Min., I
OH
= 4.0 mA
2.4
--
V
V
OL
Output LOW Voltage
V
CC
= Min., I
OL
= 8.0 mA
--
0.4
V
V
IH
Input HIGH Voltage
2
V
CC
+ 0.3V
V
IL
Input LOW Voltage
(1)
0.30.8
V
I
LI
Input Leakage
GND - V
IN
- V
CC
1
1
A
I
LO
Output Leakage
GND - V
OUT
- V
CC
, Outputs Disabled
2
2
A
Note:
1. V
IL
(min.) = 3.0V for pulse width less than 10 ns.
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol Parameter
Value
Unit
V
CC
Supply Voltage with Respect to GND
0.5 to +4.6
V
V
TERM
Terminal Voltage with Respect to GND
0.5 to Vcc + 0.5
V
T
STG
Storage Temperature
65 to +150
C
P
T
Power Dissipation
1.0
W
I
OUT
DC Output Current (LOW)
20
mA
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
IS61LV3216L
ISSI
4
Integrated Silicon Solution, Inc. -- 1-800-379-4774
Rev. A
12/19/00
READ CYCLE SWITCHING CHARACTERISTICS
(1)
(Over Operating Range)
-10
-12
-15
-20
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
t
RC
Read Cycle Time
10
--
12
--
15
--
20
--
ns
t
AA
Address Access Time
--
10
--
12
--
15
--
20
ns
t
OHA
Output Hold Time
3--
3--
3--
3--
ns
t
ACE
CE Access Time
--
10
--
12
--
15
--
20
ns
t
DOE
OE Access Time
--
5
--
6
--
7
--
8
ns
t
HZOE
(2)
OE to High-Z Output
0
5
0
6
0
7
0
8
ns
t
LZOE
(2)
OE to Low-Z Output
0
--
0
--
0
--
0
--
ns
t
HZCE
(2
CE to High-Z Output
0
5
0
6
0
7
0
8
ns
t
LZCE
(2)
CE to Low-Z Output
3--
3--
3--
3--
ns
t
BA
LB, UB Access Time
--
5
--
6
--
7
--
8
ns
t
HZB
LB, UB to High-Z Output
0
5
0
6
0
7
0
8
ns
t
LZB
LB, UB to Low-Z Output
5
--
5
--
5
--
5
--
ns
Notes:
1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of
0 to 3.0V and output loading specified in Figure 1a.
2. Tested with the load in Figure 1b. Transition is measured 500 mV from steady-state voltage. Not 100% tested.
3. Not 100% tested.
AC TEST CONDITIONS
Parameter
Unit
Input Pulse Level
0V to 3.0V
Input Rise and Fall Times
3 ns
Input and Output Timing
1.5V
and Reference Level
Output Load
See Figures 1a and 1b
AC TEST LOADS
Figure 1a.
Figure 1b.
319
30 pF
Including
jig and
scope
353
OUTPUT
3.3V
319
5 pF
Including
jig and
scope
353
OUTPUT
3.3V
CAPACITANCE
(1)
Symbol
Parameter
Conditions
Max.
Unit
C
IN
Input Capacitance
V
IN
= 0V
6
pF
C
OUT
Input/Output Capacitance
V
OUT
= 0V
8
pF
Note:
1. Tested initially and after any design or process changes that may affect these parameters.
IS61LV3216L
1
2
3
4
5
6
7
8
9
10
11
12
ISSI
Integrated Silicon Solution, Inc. -- 1-800-379-4774
5
Rev. A
12/19/00
DATA VALID
PREVIOUS DATA VALID
t
AA
t
OHA
t
OHA
t
RC
D
OUT
ADDRESS
t
RC
t
OHA
t
AA
t
DOE
t
LZOE
t
ACE
t
LZCE
t
HZOE
HIGH-Z
DATA VALID
t
HZB
ADDRESS
OE
CE
LB, UB
D
OUT
t
HZCE
t
BA
t
LZB
READ CYCLE NO. 2
(1,3)
AC WAVEFORMS
READ CYCLE NO. 1
(1,2)
(Address Controlled) (
CE = OE = V
IL
,
UB or LB = V
IL
)
Notes:
1.
WE is HIGH for a Read Cycle.
2. The device is continuously selected.
OE, CE, UB, or LB = V
IL
.
3. Address is valid prior to or coincident with
CE LOW transition.
IS61LV3216L
ISSI
6
Integrated Silicon Solution, Inc. -- 1-800-379-4774
Rev. A
12/19/00
WRITE CYCLE SWITCHING CHARACTERISTICS
(1,3)
(Over Operating Range)
-10
-12
-15
-20
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
t
WC
Write Cycle Time
10
--
12
--
15
--
20
--
ns
t
SCE
CE to Write End
8
--
9
--
10
--
12
--
ns
t
AW
Address Setup Time
9
--
10
--
10
--
12
--
ns
to Write End
t
HA
Address Hold from Write End
1
--
1
--
1
--
1
--
ns
t
SA
Address Setup Time
0
--
0
--
0
--
0
--
ns
t
PWB
LB, UB Valid to End of Write
9
--
10
--
11
--
12
--
ns
t
PWE
WE Pulse Width
7
--
8
--
10
--
11
--
ns
t
SD
Data Setup to Write End
5
--
6
--
7
--
--
8
ns
t
HD
Data Hold from Write End
0
--
0
--
0
--
0
--
ns
t
HZWE
(2)
WE LOW to High-Z Output
--
5
--
6
--
7
--
8
ns
t
LZWE
(2)
WE HIGH to Low-Z Output
1
--
1
--
1
--
1
--
ns
Notes:
1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse
levels of 0 to 3.0V and output loading specified in Figure 1a.
2. Tested with the load in Figure 1b. Transition is measured 500 mV from steady-state voltage. Not 100%
tested.
3. The internal write time is defined by the overlap of
CE LOW and UB or LB, and WE LOW. All signals must be
in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and
Hold timing are referenced to the rising or falling edge of the signal that terminates the write.
IS61LV3216L
1
2
3
4
5
6
7
8
9
10
11
12
ISSI
Integrated Silicon Solution, Inc. -- 1-800-379-4774
7
Rev. A
12/19/00
Notes:
1. WRITE is an internally generated signal asserted during an overlap of the LOW states on the
CE and WE inputs and at least
one of the
LB and UB inputs being in the LOW state.
2. WRITE = (
CE)
[
(
LB) = (UB)
]
(
WE).
AC WAVEFORMS
WRITE CYCLE NO. 1 (
WE Controlled)
(1,2)
UNDEFINED
UNDEFINED
t
WC
t
SCE
t
PWB
t
AW
t
HA
HIGH-Z
HIGH-Z
t
PWE
t
HD
t
SA
t
HZWE
ADDRESS
CE
LB, UB
WE
WRITE
(1)
D
OUT
D
IN
t
LZWE
t
SD
IS61LV3216L
ISSI
8
Integrated Silicon Solution, Inc. -- 1-800-379-4774
Rev. A
12/19/00
ORDERING INFORMATION
Commercial Range: 0C to +70C
Speed (ns) Order Part No.
Package
10
IS61LV3216L-10T
Plastic TSOP (Type II)
IS61LV3216L-10K
400-mil Plastic SOJ
12
IS61LV3216L-12T
Plastic TSOP (Type II)
IS61LV3216L-12K
400-mil Plastic SOJ
15
IS61LV3216L-15T
Plastic TSOP (Type II)
IS61LV3216L-15K
400-mil Plastic SOJ
20
IS61LV3216L-20T
Plastic TSOP (Type II)
IS61LV3216L-20K
400-mil Plastic SOJ
ORDERING INFORMATION
Industrial Range: 40C to +85C
Speed (ns) Order Part No.
Package
12
IS61LV3216L-12TI Plastic TSOP (Type II)
IS61LV3216L-12KI 400-mil Plastic SOJ
15
IS61LV3216L-15TI Plastic TSOP (Type II)
IS61LV3216L-15KI 400-mil Plastic SOJ
20
IS61LV3216L-20TI Plastic TSOP (Type II)
IS61LV3216L-20KI 400-mil Plastic SOJ
ISSI
Integrated Silicon Solution, Inc.
2231 Lawson Lane
Santa Clara, CA 95054
Tel: 1-800-379-4774
Fax: (408) 588-0806
E-mail: sales@issi.com
www.issi.com