ChipFind - документация

Электронный компонент: CCM03-3001R102

Скачать:  PDF   ZIP
Dimensions are shown in mm
Dimensions subject to change
www.ittcannon.com
Contacts
Copper alloy
Plating
Contact area : Gold alloy inlay or gold over nickel
Terminals : Tin lead (2 min)
Moldings
High temp. thermoplastic UL 94V-0 rated
Slide lock/metal cover
Stainless steel
Number of Contacts
6 or 8
Mechanical life, hinged cover
10,000 cycles min
Mechanical life, fixed cover
50,000 cycles
Card insertion force
Hinged cover: 1 N max
Fixed cover: 3 N max
Card extraction force
Hinged cover: 1 N max
Fixed cover: 0.80 N min / 3 N max
Contact force
0.25 N min / 0.50 N max
Slide locking force
2 N min / 6 N max
Vibration
Frequency 10 to 500 Hz. Acceleration 50m/s
2
Duration 6 hours - amplitude 0,35 mm
Max electrical discontinuity 1s
Shock
Peak value 500 m/s
2
Duration 11 ms
3 shocks in each direction of each axis
Max electrical discontinuity 1 s
Insulation resistance
1,000 M
min
Resistance 100
m
max
Current rating
10 A min / 1 A max
Dielectric strength
750 Vrms min
Card detection switch
Normally open
Contact resistance
100 m
max
Dielectric strength
250 Vrms min
Current rating
1 mA min / 10m A max
Maximum power
0.2 VA
Operating temperature
-40C to +85C
Soldering temperature
Temperature/time profile acc. to CECC00802
para. 6.1, Fig. 3 with peak temperature 250C
Damp heat
IEC 512 test number 11c (10 days)
Salt mist
IEC 512 test number 11f (96 hours)
Quantity per reel, see table next page.
19
CCM03 MK II
A new range of CCM03 connectors
have been developed to interface with
SIM/SAM cards as defined by GSM11-
11 and ENV1375-1. The connectors are
available with either hinged covers or
fixed covers and have been designed to
minimize the amount of space needed
for PCB mounting.
Features
Hinged Cover
Available with 6 or 8 contacts, with or
without PCB locating pegs.
Available with insulated card presence
switch.
The cover springs open when
unlocked while the card is in place.
The molding is polarized so that the
cover can only be closed if the card is
correctly inserted.
The cover can be replaced without
removing the connector from the PCB.
Inspection slots allow an electrical test
to be made without opening the cover.
The overall height of the connector is
only 2,5 mm. The amount of space
needed to mount the connector is just
29,65 mm x 17,2 mm.
Fixed Cover
Available with 6 or 8 contacts.
The overall height of the connector is
2,85 mm max. Only 25,5 mm x 17,2
mm of board space is required to
mount the connector.
General
With tape and reel packaging as stan-
dard, the connectors are designed to
be automatically pick-and-placed.
The high temperature thermoplastic
moldings are suited for infrared and
convection soldering processes.
By using an inlay finish in the contact
area the life of the precious metal is
extended by over 10 times that of
standard gold plating.
Robustly formed printed circuit tails
allow a co-planarity of 0,05 mm to
be maintained.
Construction
Mechanical Data
Contact Electrical Data
Switch Electrical Data
Environmental Data
Packaging
Dimensions are shown in mm
Dimensions subject to change
www.ittcannon.com
Dimensional Drawings
1,25
1,25
(2,7 max.
includes solder tails)
2,5
11,35
17,2
3,81 3,8
3,5
2,45
1,25
5,65
0,2
13,8
29,65
0,1
0 -0,1
0,7
250'
0,8
(REF.)
25,5
0,65
R 1,9
3,81 3,81
25,4
0,2
0,4
180max
(REF.)
25,5
25
28,4
MICROSIM CARD
XX-XXX
SEE DETAIL A
Date Code area
Mated condition
R 1,9
Pick and place area
3,5
Slider locked
Bump
DETAIL A
PCB Layout
Unless otherwise stated, tolerances are 0,10 mm
Hinged Cover CCM03 - 3001 (6 contacts)
3002 (6 contacts - PCB locating pegs)
3003 (8 contacts)
3004 (8 contacts - PCB locating pegs)
CCM03-3001 / 3002
CCM03-3003 / 3004
Notes:
Coplanarity of soldering surfaces: 0,05 mm
*Pegs: Height 0,7 mm and 1 mm
20
CCM03 MK II
Part Number
Number of
Cover
PCB Locating
Quantity
Contact
Switch Card Presence
Contacts Pegs
per
reel
Finish
lock
switch
CCM03-3001 R102
6
Hinged
No
1000
Inlay
No
No
CCM03-3002 R102
6
Hinged
Yes
1000
Inlay
No
No
CCM03-3003 R102
8
Hinged
No
1000
Inlay
No
No
CCM03-3004 R102
8
Hinged
Yes
1000
Inlay
No
No
CCM03-3009 R102
6
Hinged
No
1000
Gold
No
No
CCM03-3010 R102
6
Hinged
Yes
1000
Gold
No
No
CCM03-3011 R102
8
Hinged
No
1000
Gold
No
No
CCM03-3012 R102
8
Hinged
Yes
1000
Gold
No
No
CCM03-3013 R102
6
Hinged
No
1000
Gold
No
Yes (insulated)
CCM03-3514 R122
6
Hinged
No
1200
Inlay
Yes
No
Ordering Code
CCM03-3504 R122
8
Fixed
No
1200
Inlay
No
No
CCM03-3505 R122
6
Fixed
No
1200
Inlay
No
No
25,5
2,5
5,5
5,5
3,81 3,81
1,8
1,27
8,6
23,2
1,5
1,5
9,34
6,35
20,32
10,16
5,08
1,2
+0,1
0
0,1
1,44
2x
2,54
1,3
0,2
Current location according to
ENV1375-1 & GSM11-11
Contact foot area
0,8 x 1
(Component side)
6x
C5
Plastic outline
Pad
Prohibited area
C6
C7
C1
C2
C3
2x
25,5
2,5
5,5
5,5
3,81 3,81
1,8
1,27
8,6
23,2
1,5
1,5
9,34
1,55
3x
2,54
1,3
0,2
Contact location according to
ENV1375-1 & GSM11-11
C5
0,8 x 1
(Component side)
Prohibited area
C6
C7
C1
C2
C3
C8
C4
8x
Plastic outline
Pad
21
Dimensions are shown in mm
Dimensions subject to change
www.ittcannon.com
Dimensional Drawings
PCB Layout
Unless otherwise stated, tolerances are 0,10 mm
Hinged Cover CCM03 - 3013 (6 contacts + Card Presence Switch)
CCM03 - 3013 (6 contacts + Card Presence Switch)
Note: Coplanarity of soldering surfaces: 0,05 mm
CCM03 MK II Hinged Cover
Insulated Card Presence Switch
25,5
2,5
5,5
5,5
3,81 3,81
1,8
1,27
8,6
23,2
1,5
1,5
9,34
1,55
3x
2,54
1,3
0,2
Contact location according to
ENV1375-1 & GSM11-11
C5
Contact foot area
0,8 x 1
(Component side)
Prohibited area
C6
C7
C1
C2
C3
SW
SW
8x
Plastic outline
Pad
1,25
1,25
(2,7 max. includes solder tails)
2,5
1
1
,35
17,2
3,81
3,8
3,5
2,45
1,25
5,65
0,2
13,8
29,65
0,7
250'
13,15
2,1
9,6
3,7
0,65
R 1,9
1
0,3
A
0,1
0 -0,1
0,8
25,5
0,2
0,4
(REF.)
25,5
3x
2,54
8,6
1,27
3,81 3,81
25,4
0,2
0,4
180max
25
28,4
15
(REF.)
25,5
MICROSIM CARD
XX-XXX
SEE DETAIL A
Date Code area
Mated condition
8x
DETAIL
insulated blade switch
R 1,9
Pick and place area
3,5
Slider locked
DETAIL A
Plastic actuator
A
22
Dimensions are shown in mm
Dimensions subject to change
www.ittcannon.com
Dimensional Drawings
11,35
17,2
3,81 3,8
0,7
1,25
1,25
2,45
3,5
5,65
0,2
13,8
29,65
250'
2x
2,54
13,15
0,4
25,5
0,2
1,25
R 1,9
9,6
3,7
2,1
0,65
0,8
(REF.)
25,5
0,6
0,3
A
8,6
1,27
5,08
5,08
(3,2 max includes solder tails)
3
0,5
+0,1 0
0,45
0,1 0
3,81
3,81
0,4
25,4
0,2
180max
28,4
15
(REF.)
25,5
25
MICROSIM CARD
Bump
XX-XXX
SEE DETAIL A
Date Code area
Mated condition
8x
on contacts & left lock switch terminal
on right lock switch terminal only
R 1,9
Pick and place area
3,5
Slider locked
Left lock switch terminal
Right lock switch terminal
DETAIL A
A
PCB Layout
3,81 3,81
2,5
5,5
5,5
25,5
3
3,4
5,6
7,6
2,4
1,8
1,4
5,08
5,08
1
0,2
23,2
1,5
1,5
1,55
9,34
2x
2,54
8,6
1,27
C5
Contact foot area
0,8 x 0,6
(Component side)
C6
C7
C1
C2
C3
8x
Contact location according to
ENV1375-1 & GSM11-11
Plastic outline
Pad
Prohibited area
Unless otherwise stated, tolerances are 0,10 mm
Hinged Cover CCM03 - 3514 (6 contacts - with switch on metal lock)
CCM03 - 3514 (6 contacts - with switch on metal lock)
Note: Coplanarity of soldering surfaces: 0,05 mm
CCM03 MK II Hinged Cover
23
Dimensions are shown in mm
Dimensions subject to change
www.ittcannon.com
Dimensional Drawings
A
A
B
B
(REF.)
3,45
21,55
1,4
+0,05
0
0,15 min
2,45
1,6
1,4+0,05
0
0,8
300'
0,8
1,25
0,05
0,2
2,65
12,1
15,2
+0,1 0
17,2
0,05
1,9
2,3
400'
(REF.)
25,5
0,75
25,5
0,2
12,7
2,5
3x
2,54
1
0,3
A
10,16
3,81
3,81
0,3
0,02
0,4
2,54
0,1
0 -0,1
8,6
1,27
12,75
25,5
(REF.)
25,5
(REF
.)
17,2
(REF.)
9,75
12,9
0,4
2,85 (3 max includes solder tails)
Date Code area
Card stop
Mated condition
XX-XXX
Pick and place area
3,5
SEE DETAIL A
8x
DETAIL A
A
PCB Layout
Unless otherwise stated, tolerances are 0,10 mm
Fixed cover CCM03 - 3504 (8 contacts)
CCM03 - 3505
CCM03 - 3504
Note: Coplanarity of soldering surfaces: 0,05 mm
CCM03 MK II Fixed Cover
2,5
5,5
5,5
1,8
25,5
3,81
3,81
2x
1,4
+0,05
0
8,6
6,35
2,54
1,5
23,2
1,5
1,44
3x
2,54
1,27
12,7
1,3
0,2
Contact location according to
ENV1375-1 & GSM11-11
C1
C5
Contact foot area
0,8 x 1
C2
C3
C4
C6
C7
C8
8x
(Component side)
Plastic outline
Pad
Prohibited area
2,5
5,5
5,5
1,8
3,81
3,81
25,5
2x
1,4
+0,05
0
8,6
6,35
2,54
1,5
23,2
1,5
1,44
2x
2,54
1,27
1,3
0,2
12,7
ENV1375-1 & GSM11-11
C1
C5
Contact foot area
0,8 x 1
C2
C3
C6
C7
6x
(Component side)
Plastic outline
Pad
Prohibited area