SPEC NO: DSAB7757
REV NO: V.5 DATE: MAR/11/2005 PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu DRAWN: Y.W.WANG ERP:1203000193
Package Dimensions
AP2012SYC SUPER BRIGHT YELLOW
Description
The Super Bright Yellow device is made with DH InGaAlP
(on GaAs substrate) light emitting diode chip.
2.0x1.25mm SMD CHIP LED LAMP
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is
0.1(0.004") unless otherwise noted.
3. Specifications are subject to change without notice.
Features
2.0mmx1.25mm SMT LED,1.1mm THICKNESS.
LOW POWER CONSUMPTION.
WIDE VIEWING ANGLE.
IDEAL FOR BACKLIGHT AND INDICATOR.
VARIOUS COLORS AND LENS TYPES AVAILABLE.
PACKAGE : 2000PCS / REEL.
RoHS COMPLIANT.
SPEC NO: DSAB7757
REV NO: V.5 DATE: MAR/11/2005 PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu DRAWN: Y.W.WANG ERP:1203000193
Selection Guide
Note:
1.
1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at T
A
=25C
Absolute Maximum Ratings at T
A
=25C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No.
Dice
Lens Type
Iv (mcd)
@ 20mA
Viewing
Angle
Min.
Typ.
2
1/2
AP2012SYC
SUPER BRIGHT YELLOW (InGaAIP)
WATER CLEAR
36
150
120
Symbol
Parameter
Device
Typ.
Max.
Test Conditions
Units
peak
Peak Wavelength
Super Bright Yellow
590
nm
I
F
=20mA
D
Dominant Wavelength
Super Bright Yellow
588
nm
I
F
=20mA
1/2
Spectral Line Half-width
Super Bright Yellow
28
nm
I
F
=20mA
C
Capacitance
Super Bright Yellow
25
pF
V
F
=0V;f=1MHz
V
F
Forward Voltage
Super Bright Yellow
2.0
2.5
V
I
F
=20mA
I
R
Reverse Current
Super Bright Yellow
10
uA
V
R
= 5V
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
Reverse Voltage
5
V
Operating/Storage Temperature
-40C To +85C
SPEC NO: DSAB7757
REV NO: V.5 DATE: MAR/11/2005 PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu DRAWN: Y.W.WANG ERP:1203000193
Super Bright Yellow
AP2012SYC
SPEC NO: DSAB7757
REV NO: V.5 DATE: MAR/11/2005 PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu DRAWN: Y.W.WANG ERP:1203000193
AP2012SYC
Recommended Soldering Pattern
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength), the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
Tape Specifications
(Units : mm)
PDF 
ZIP