LTC1287
1
1287fa
FEATURES
DESCRIPTIO
U
KEY SPECIFICATIO S
U
TYPICAL APPLICATIO
U
3V Single Chip 12-Bit
Data Acquisition System
s
Single Supply 3.3V Operation
s
Built-In Sample-and-Hold
s
Direct 3-Wire Interface to Most MPU Serial Ports and
All MPU Parallel Ports
s
30kHz Maximum Throughput Rate
The LTC
1287 is a 3V data acquisition component which
contains a serial I/O successive approximation A/D con-
verter. The device specifications are guaranteed at a
supply voltage of 2.7V. It uses LTCMOS
TM
switched ca-
pacitor technology to perform a 12-bit unipolar, A/D
conversion. The differential input has an on-chip sample-
and-hold on the (+) input.
The serial I/O is designed to communicate without external
hardware to most MPU serial ports and all MPU parallel
I/O ports allowing data to be transmitted and received over
three wires. The low voltage operating capability and the
low power consumption of this device make it ideally
suited for battery applications. Given the ease of use, small
package size and the minimum number of interconnects
for I/O, the LTC1287 can be used for remote sensing
applications.
s
Minimum Guaranteed Supply Voltage: 2.7V
s
Resolution: 12 Bits
s
Fast Conversion Time: 24
s Max Over Temp.
s
Low Supply Current: 1.0mA
s
Battery-Powered Instruments
s
Data Logger
s
Data Acquisition Modules
LTCMOS is a trademark of Linear Technology Corporation
V
CC
CLK
D
OUT
V
REF
LTC1287
CS
+IN
IN
GND
LT1004-1.2
10k
22
F TANTALUM
22
F
TANTALUM
+
DIFFERENTIAL INPUTS
COMMON MODE RANGE
0V TO V
CC
*
FOR OVERVOLTAGE PROTECTION, LIMIT THE INPUT CURRENT TO 15mA
PER PIN OR CLAMP THE INPUTS TO V
CC
AND GND WITH 1N4148 DIODES.
CONVERSION RESULTS ARE NOT VALID WHEN THE SELECTED CHANNEL OR
OTHER CHANNEL IS OVERVOLTAGED (V
IN
< GND OR V
IN
> V
CC
). SEE SECTION
ON OVERVOLTAGE PROTECTION IN THE APPLICATIONS INFORMATION.
*
3V
LITHIUM
TO AND FROM MPU
1287 TA01
+
+
3V Differential Input Data Acquisition System
INL with V
REF
= 1.2V
CODE
0
ERROR (LSB)
0.5
1.0
2048
LTC1287 TA02
0
1.0
512
1024
1536
0.5
2560
3072
3584
4096
, LTC and LT are registered trademarks of Linear Technology Corporation.
APPLICATIO S
U
2
LTC1287
1287fa
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
f
CLK
Clock Frequency
(Note 6)
(Note 9)
0.5
MHz
t
SMPL
Analog Input Sample Time
See Operating Sequence
1.5
CLK Cycles
t
CONV
Conversion Time
See Operating Sequence
12
CLK Cycles
t
CYC
Total Cycle Time
See Operating Sequence (Note 6)
14 CLK+5.0
s
Cycles
t
dDO
Delay Time, CLK
to D
OUT
Data Valid
See Test Circuits
q
250
450
ns
t
dis
Delay Time, CS
to D
OUT
Hi-Z
See Test Circuits
q
80
160
ns
t
en
Delay Time, CLK
to D
OUT
Enabled
See Test Circuits
q
130
250
ns
The
q
denotes the specifications
which apply over the full operating temperature range, otherwise specifications are at T
A
= 25
C. (Note 3)
The
q
denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at T
A
= 25
C. (Note 3)
W
U
U
PACKAGE/ORDER I FOR ATIO
A
U
G
W
A
W
U
W
A
R
BSOLUTE
XI
TI
S
(Notes 1 and 2)
Supply Voltage (V
CC
) to GND .................................. 12V
Voltage
Analog and Reference Inputs .... 0.3V to V
CC
+ 0.3V
Digital Inputs ........................................ 0.3V to 12V
Digital Outputs .......................... 0.3V to V
CC
+ 0.3V
Power Dissipation ............................................. 500mW
Operating Temperature Range .................... 0
C to 70
C
Storage Temperature Range ................. 65
C to 150
C
Lead Temperature (Soldering, 10 sec.)................ 300
C
ORDER PART
NUMBER
LTC1287BCN8
LTC1287CCN8
LTC1287B
LTC1287C
CO VERTER A D ULTIPLEXER CHARACTERISTICS
U
U W
AC CHARACTERISTICS
LTC1287B/LTC1287C
0.05V to V
CC
+ 0.05V
T
JMAX
= 150
C,
JA
= 100
C/W (J)
Consult LTC Marketing for parts specified with wider operating temperature ranges.
T
JMAX
= 100
C,
JA
= 130
C/W (N)
LTC1287BCJ8
LTC1287CCJ8
OBSOLETE PACKAGE
Consider N8 Package for Alternate Source
J8 PACKAGE
8-LEAD CERAMIC DIP
1
2
3
4
5
6
7
8
TOP VIEW
V
CC
CLK
D
OUT
V
REF
CS
+IN
IN
GND
N8 PACKAGE
8-LEAD PLASTIC DIP
PARAMETER
CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
Offset Error
V
CC
= 2.7V (Note 4)
q
3.0
3.0
LSB
Linearity Error (INL)
V
CC
= 2.7V (Notes 4 & 5)
q
0.5
0.5
LSB
Gain Error
V
CC
= 2.7V (Note 4)
q
0.5
1.0
LSB
Minimum Resolution for Which No
q
12
12
Bits
Missing Codes are Guaranteed
Analog and REF Input Range
(Note 7)
V
On Channel Leakage Current (Note 8)
On Channel = 3V
q
1
1
A
Off Channel = 0V
On Channel = 0V
q
1
1
A
Off Channel = 3V
Off Channel Leakage Current (Note 8)
On Channel = 3V
q
1
1
A
Off Channel = 0V
On Channel = 0V
q
1
1
A
Off Channel = 3V
LTC1287
3
1287fa
AC CHARACTERISTICS
LTC1287B/LTC1287C
ELECTRICAL C
C
HARA TER STICS
DIGITAL A D
U
I
DC
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: All voltage values are with respect to ground (unless otherwise
noted).
Note 3: V
CC
= 3V, V
REF
= 2.5V, CLK = 500kHz unless otherwise specified.
Note 4: One LSB is equal to V
REF
divided by 4096. For example, when V
REF
= 2.5V, 1LSB = 2.5V/4096 = 0.61mV.
Note 5: Integral nonlinearity error is defined as the deviation of a code
from a straight line passing through the actual endpoints of the transfer
curve. The deviation is measured from the center of the quantization band.
Note 6: Recommended operating conditions.
LTC1287B/LTC1287C
Note 7: Two on-chip diodes are tied to each analog input which will
conduct for analog voltages one diode drop below GND or one diode drop
above V
CC
. Be careful during testing at low V
CC
levels, as high level analog
inputs can cause this input diode to conduct, especially at elevated
temperature, and cause errors for inputs near full scale. This spec allows
50mV forward bias of either diode. This means that as long as the analog
input does not exceed the supply voltage by more than 50mV, the output
code will be correct.
Note 8: Channel leakage current is measured after the channel selection.
Note 9: Increased leakage currents at elevated temperatures cause the
S/H to droop, therefore it is recommended that f
CLK
30kHz at 85
C and
f
CLK
3kHz at 25
C.
The
q
denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at T
A
= 25
C. (Note 3)
The
q
denotes the specifications which
apply over the full operating temperature range, otherwise specifications are at T
A
= 25
C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
t
hDO
Time Output Data Remains Valid After CLK
50
ns
t
f
D
OUT
Fall Time
See Test Circuits
q
40
100
ns
t
r
D
OUT
Rise Time
See Test Circuits
q
40
100
ns
t
WHCLK
CLK High Time
V
CC
= 3V (Note 6)
600
ns
t
WLCLK
CLK Low Time
V
CC
= 3V (Note 6)
800
ns
t
suCS
Setup Time, CS
Before CLK
V
CC
= 3V (Note 6)
100
ns
t
WHCS
CS High Time Between Data Transfer Cycles
V
CC
= 3V (Note 6)
5.0
s
t
WLCS
CS Low Time During Data Transfer
V
CC
= 3V (Note 6)
14
CLK Cycles
C
IN
Input Capacitance
Analog Inputs On Channel
100
pF
Analog Inputs Off Channel
5
pF
Digital Inputs
5
pF
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
IH
High Level Input Voltage
V
CC
= 3.6V
q
2.1
V
V
IL
Low Level Input Voltage
V
CC
= 3.0V
q
0.45
V
I
IH
High Level Input Current
V
IN
= V
CC
q
2.5
A
I
IL
Low Level Input Current
V
IN
= 0V
q
2.5
A
V
OH
High Level Output Voltage
V
CC
= 3.0V, I
O
= 20
A
2.90
V
I
O
= 400
A
q
2.7
2.85
V
V
OL
Low Level Output Voltage
V
CC
= 3.0V, I
O
= 20
A
0.05
V
I
O
= 400
A
q
0.10
0.3
V
I
OZ
High Z Output Leakage
V
OUT
= V
CC
, CS High
q
3
A
V
OUT
= 0V, CS High
q
3
A
I
SOURCE
Output Source Current
V
OUT
= 0V
10
mA
I
SINK
Output Sink Current
V
OUT
= V
CC
9
mA
I
CC
Positive Supply Current
CS High
q
1.5
5
mA
I
REF
Reference Current
V
REF
= 2.5V
q
10
50
A
4
LTC1287
1287fa
REFERENCE VOLTAGE (V)
0
0
CHANGE IN LINEARITY (LSB = 1/4096
V
REF
)
0.1
0.2
0.3
0.4
0.5
0.5
1.0
1.5
2.0
LTC1287 G4
2.5
3.0
V
CC
= 3V
C
C
HARA TERISTICS
U
W
A
TYPICAL PERFOR
CE
Supply Current vs Supply Voltage
Change in Linearity vs Reference
Voltage
Change in Gain vs Temperature
D
OUT
Delay Time vs Temperature
Change in Offset vs Temperature
Change in Gain vs Reference
Voltage
REFERENCE VOLTAGE (V)
0
0.5
CHANGE IN GAIN (LSB = 1/4096
V
REF
)
0.4
0.3
0.2
0.1
0
0.5
1.0
1.5
2.0
LTC1287 G5
2.5
3.0
V
CC
= 3V
Supply Current vs Temperature
REFERENCE VOLTAGE (V)
0
0
OFFSET (LSB = 1/4096
V
REF
)
0.1
0.3
0.4
0.5
2.0
0.9
LTC1287 G3
0.2
1.0
3.0
0.6
0.7
0.8
0.5
1.5
2.5
V
CC
= 3V
V
OS
= 0.250mV
V
OS
= 0.125mV
Unadjusted Offset Voltage vs
Reference Voltage
AMBIENT TEMPERATURE (
C)
40
0
MAGNITUDE OF OFFSET CHANGE (LSB)
0.2
0.5
0
40
60
LTC1287 G6
0.1
0.4
0.3
20
20
80
100
V
CC
= 3V
V
REF
= 2.5V
CLK = 500kHz
Change in Linearity vs
Temperature
AMBIENT TEMPERATURE (
C)
40
0
MAGNITUDE OF LINEARITY CHANGE (LSB)
0.2
0.5
0
40
60
LTC1287 G7
0.1
0.4
0.3
20
20
80
100
V
CC
= 3V
V
REF
= 2.5V
CLK = 500kHz
AMBIENT TEMPERATURE (
C)
40
200
250
350
20
60
LTC1287 G9
150
100
20
0
40
80
100
50
0
300
D
OUT
DELAY TIME FROM CLK
(ns)
V
CC
= 3V
MSB-FIRST DATA
LSB-FIRST DATA
SUPPLY VOLTAGE (V)
2.7
0.8
SUPPLY CURRENT (mA)
1.0
1.4
1.6
1.8
2.8
2.2
2.9
3.1 3.2
3.6
LTC1287 G1
1.2
2.4
2.6
2.0
2.8
3.0
3.3 3.4 3.5
CLK = 500kHz
T
A
= 25
C
TEMPERATURE (
C)
40
1.3
SUPPLY CURRENT (mA)
1.4
1.6
1.7
1.8
10
20
35
95
LTC1287 G2
1.5
25
5
50
65
80
1.9
CLK = 500kHz
V
CC
= 3V
AMBIENT TEMPERATURE (
C)
40
0
MAGNITUDE OF GAIN CHANGE (LSB)
0.2
0.5
0
40
60
LTC1287 G8
0.1
0.4
0.3
20
20
80
100
V
CC
= 3V
V
REF
= 2.5V
CLK = 500kHz
LTC1287
5
1287fa
C
C
HARA TERISTICS
U
W
A
TYPICAL PERFOR
CE
R
SOURCE
(
)
100
0
MAXIMUM CLK FREQUENCY* (MHz)
300
400
500
1k
10k
100k
LTC G10
200
100
V
CC
= 3V
V
REF
= 2.5V
CLK = 500kHz
+IN
IN
+V
IN
R
SOURCE
R
SOURCE
+ (
)
100
1k
10k
LTC1287 G13
1
S & H ACQUISITION TIME TO 0.02% (
s)
10
100
+
V
IN
R
SOURCE
+
V
REF
= 2.5V
V
CC
= 3V
T
A
= 25
C
0V TO 2.5V INPUT STEP
Sample-and-Hold Acquisition
Time vs Source Resistance
AMBIENT TEMPERATURE (
C)
50
0
INPUT CHANNEL LEAKAGE CURRENT (nA)
100
300
400
500
1000
700
10
30
50
130
LTC1287 G14
200
800
900
600
30
10
70
90 110
ON CHANNEL
OFF CHANNEL
GUARANTEED
Input Channel Leakage Current vs
Temperature
REFERENCE VOLTAGE (V)
0
0
PEAK-TO-PEAK NOISE ERROR (LSB)
0.2
0.3
0.4
0.5
0.6
0.7
0.5
1.0
1.5
2.0
LTC1287 G15
2.5
0.8
0.9
1.0
0.1
3.0
LTC1287 NOISE = 200
V
P-P
Noise Error vs Reference Voltage
Maximum Clock Rate vs Source
Resistance
Minimum Clock Rate for 0.1LSB
Error**
Maximum Filter Resistor vs Cycle
Time
*** MAXIMUM R
FILTER
REPRESENTS THE FILTER RESISTOR VALUE AT WHICH A 0.1LSB
CHANGE IN FULL SCALE ERROR FROM ITS VALUE AT R
FILTER
= 0
IS FIRST DETECTED.
* MAXIMUM CLK FREQUENCY REPRESENTS THE CLK FREQUENCY AT WHICH A 0.1LSB
SHIFT IN THE ERROR AT ANY CODE TRANSITION FROM ITS 500kHz VALUE IS FIRST DETECTED.
** AS THE CLK FREQUENCY IS DECREASED FROM 1MHz, MINIMUM CLK FREQUENCY
(
ERROR
0.1LSB) REPRESENTS THE FREQUENCY AT WHICH A 0.1LSB SHIFT IN ANY
CODE TRANSITION FROM ITS 500kHz VALUE IS FIRST DETECTED.
PI FU CTIO S
U
U
U
CYCLE TIME (
s)
10
MAXIMUM R
FILTER
*** (
)
100
1k
10k
10
1000
10000
LTC1287 G12
1
100
+
V
IN
C
FILTER
1
F
R
FILTER
AMBIENT TEMPERATURE (
C)
50
MINIMUM CLK FREQUENCY (MHz) 0.05
0.10
0.15
0.20
25
0
25
50
LTC1287 G11
75
100
0.25
V
CC
= 3V
CS (Pin 1): Chip Select Input. A logic low on this input
enables the LTC1287.
+IN, IN (Pin 2,3): Analog Inputs. These inputs must be
free of noise with respect to GND.
GND (Pin 4): Analog Ground GND should be tied directly
to an analog ground plane.
V
REF
(Pin 5): Reference Input. The reference input defines
the span of the A/D converter and must be kept free of
noise with respect to GND.
D
OUT
(Pin 6): Digital Data Output. The A/D conversion
result is shifted out of this output.
CLK (Pin 7): Shift Clock. This clock synchronizes the serial
data transfer.
V
CC
(Pin 8): Positive Supply. This supply must be kept free
of noise and ripple by bypassing directly to the analog
ground plane.
PDF 
ZIP