SCOPE: 8-CHANNEL/DUAL 4-CHANNEL CMOS, ANALOG SWITCHES
Device Type Generic Number SMD Number
01
DG408A(x)/883B 5962-9204201
02
DG409A(x)/883B 5962-9204202
Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter Mil-Std-1835 Case Outline Package Code
Maxim SMD
K E
GDIP1-T16 or CDIP2-T16 16 LEAD CERDIP J16
L X CDFP3-F16 16 LEAD FLATPACK F16
Z 2 CQCC1-N20 20-Pin Ceramic LCC L20
Absolute Maximum Ratings
Voltage Referenced to V
-
V
+
to V
-
.............................................................................................................................. 44V
V
-
to GND ......................................................................................................................... 25V
Digital Inputs Overvoltage Range 1/ ..................................................... .(V
-
-2V) to (V
+
+2V)
or 20mA whichever occurs first.
Continuous Current, Any terminal except S or D ........................................................... 30mA
Continuous Current, S or D ............................................................................................. 20mA
Current, S or D (Pulsed at 1ms, 10% duty cycle max) .................................................... 40mA
Lead Temperature (soldering, 10 seconds) ........................................................................ +300
C
Storage Temperature ........................................................................................... -65
C to +150
C
Continuous Power Dissipation .................................................................................. T
A
=
+
70
C
16 lead CERDIP(derate 10.0mW/
C above +70
C) ...................................................... 800mW
16 lead FLATPACK(derate 6.1mW/
C above +70
C) ................................................... 485mW
20 lead LCC(derate 9.1mW/
C above +70
C) ................................................................ 727mW
Junction Temperature T
J
.............................................................................................. +150
C
Thermal Resistance, Junction to Case,
JC:
Case Outline 16 lead CERDIP.......................................................................... 50
C/W
Case Outline 16 lead FLATPACK .................................................................. 65
C/W
Case Outline 20 lead LCC .............................................................................. 55
C/W
Thermal Resistance, Junction to Ambient,
JA:
Case Outline 16 lead CERDIP....................................................................... 100
C/W
Case Outline 16 lead FLATPACK ................................................................ 165
C/W
Case Outline 20 lead LCC ............................................................................. 110
C/W
Recommended Operating Conditions
Ambient Operating Range (T
A
) .................................................................... -55
C to
+
125
C
Positive Supply Voltage (V
+
) ........................................................................................... +15V
Negative Supply Voltage (V
-
) ........................................................................................... -15V
1/ Signals on S, D or IN exceeding V
+
or V
-
are clamped by internal diodes. Limit forward current to
maximum current ratings.
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of DG408A/409A/883B
19-0368
Rev. B
for SMD 5962-92042
Page 2 of
6
TABLE 1. ELECTRICAL TESTS:
TEST
Symbol
CONDITIONS
-55
C <=T
A
<= +125
C
V
+
=+15V, V
-
=-15V, GND=0V
V
AH
=2.4V, V
AL
=0.8V, V
EN
=2.4V
Unless otherwise specified
Group A
Subgroup
Device
type
Limits
Min
Limits
Max
Units
SWITCH
Analog-Signal
Range
V
ANALOG
NOTE 2
1,2,3
All
-15
15 V
Drain-Source ON
Resistance
r
DS(ON)
I
S
=-10mA, V
D
=
10V
1,3
2
All
100
125
r
DS(ON)
Matching
Between Channels
r
DS
(ON)
I
S
=-10mA, V
D
=
10V, NOTE 3
1
All
15
Source-OFF
Leakage Current
I
S(OFF)
V
S
=
10V, V
D
=
10V, V
EN
=0V
1
2
All
-0.5
-50
0.5
50
nA
Drain-OFF
Leakage Current
I
D(OFF)
V
S
=
10V, V
D
=
10V, V
EN
=0V
1
2
2
All
01
02
-1.0
-100
-50
1.0
100
50
nA
Drain-ON Leakage
Current
I
D(ON)+
I
S(ON)
V
S
=
10V, V
D
=
10V, sequence
each switch on
1
2
2
All
01
02
-1.0
-100
-50
1.0
100
50
nA
INPUT
Input
Current/Voltage
High
I
AH
V
A
= 2.4V, 15V
1,2,3
All
-10
10
A
Input
Current/Voltage
Low
I
AL
V
A
=0V, V
EN
= 0V, 2.4V
1,2,3
All
-10
10
A
Standby Positive
Supply Current
+I
SBY
V
A
=0V, V
EN
= 0V
1,2,3
All
75
A
Standby Negative
Supply Current
-I
SBY
V
A
=0V, V
EN
= 0V
1,2,3
All
-75
A
SUPPLY
Positive Supply
Current
I+
V
A
=0V, V
EN
= 2.4V
1,3
2
All
0.5
2.0
mA
Negative Supply
Current
I-
V
A
=0V, V
EN
= 2.4V
1,2,3
All
-0.5
mA
DYNAMIC
Transition Time
t
TRANS
Figure 2
9,10,11
All
250 ns
Break Before
Make Time
t
OPEN
Figure 4
9
All
10
ns
Enable Turn-On
Time
t
ON(EN)
Figure 3
9,11
10
All
150
225
ns
Enable Turn-Off
Time
t
OFF(EN)
Figure 3
9,10,11
All
150 ns
NOTE 2: Guaranteed by design.
NOTE 3:
r
DS(ON)
=
r
DS(ON)
max-
r
DS(ON)
min
FIGURE 2: TRANSITION TIME TEST CIRCUIT: See Commercial Data Sheet
FIGURE 3: ENABLE SWITCHING TIME: See Commercial Data Sheet
FIGURE 4: BREAK-BEFORE-MAKE INTERVAL: See Commercial Data Sheet
----------------------------
Electrical Characteristics of DG408A/409A/883B
19-0368
Rev. B
for SMD 5962-92042
Page 3 of
6
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125
C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125
C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2. ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Subgroups
per Method 5005, Table 1
Interim Electric Parameters
Method 5004
1
Final Electrical Parameters
Method 5005
1*, 2, 3, 7, 8, 9, 10, 11
Group A Test Requirements
Method 5005
1, 2, 3, 7**, 8**, 9, 10, 11
Group C and D End-Point Electrical Parameters
Method 5005
1
* PDA applies to Subgroup 1 only.
** Subgroups 7 and 8 tests shall be sufficient to verify the truth table.
----------------------------
Electrical Characteristics of DG408A/409A/883B
19-0368
Rev. B
for SMD 5962-92042
Page 5 of
6
PDF 
ZIP