ChipFind - документация

Электронный компонент: MX580SH/883B

Скачать:  PDF   ZIP
SCOPE: HIGH PRECISION +2.5VOLT REFERENCE
Device Type Generic Number
01
MX580S(x)/883B
02
MX580T(x)/883B
03 MX580U(x)/883B
Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter Mil-Std-1835 Case Outline Package Code
MAXIM SMD
H X MACY1-X3 3 Lead TO-52 Can G52
Absolute Maximum Ratings
Input Voltage to GND .............................................................................................. 40V
Lead Temperature (soldering, 10 seconds) ................................................................ +300
C
Storage Temperature .................................................................................. -65
C to +150
C
Continuous Power Dissipation ..............................................................................T
A
=
+
70
C
3-Pin TO-52 Can(derate 4.55mW/
C above +70
C) ................................................ 364mW
Junction Temperature T
J
........................................................................................ +150
C
Thermal Resistance, Junction to Case,
JC:
3-Pin TO-52 Can ....................................................................................... 60
C/W
Thermal Resistance, Junction to Ambient,
JA:
3-Pin TO-52 Can ..................................................................................... 220
C/W
Recommended Operating Conditions
Supply Voltage Range (V
IN
) ............................................................ 4.5V min to 30V max
Ambient Operating Range (T
A
) .............................................................. -55
C to
+
125
C
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of MX580S/T/U/883B
19-2445
Rev. B
for /883B and SMD 5962-86861
Page 2 of
6
TABLE 1 ELECTRICAL TESTS
TEST
Symbol
CONDITIONS
-55
C
T
A
+125
C
V
CC
=+15V, I
L
=0mA
Unless otherwise specified
Group A
Subgroup
Device
type
Limits
Min
Limits
Max
Units
Quiescent Current
I
Q
1
All
1.5 mA
Output Voltage
Error
V
OUT
1
01
02
03
-75
-25
-10
+75
+25
+10
mV
Line Regulation
VR
LINE1
VR
LINE2
V
CC
=7V to 30V
V
CC
=4.5V to 7V
1,2,3
01
02,03
01
02,03
-6
-2
-3
-1
+6
+2
+3
+1
mV
Load Regulation
VR
LOAD
I
L
=0mA to 10mA
1,2,3
All
-10
+10 mV
Output Voltage
Temperature
Coefficient
V
OUT
0/
T
2,3
01
02
03
-25
-11
-4.5
+25
+11
+4.5
mV
ORDERING INFORMATION
Device
Maxim Part Number
SMD Number
01
MX580SH/883B
5962-8686101XC
02
MX580TH/883B
5962-8686102XC
03
MX580UH/883B
5962-8686103XC
PIN CONFIGURATION
1
V
CC
2
V
OUT
3
GND
----------------------------
Electrical Characteristics of MX580S/T/U/883B
19-2445
Rev. B
for /883B and SMD 5962-86861
Page 3 of
5
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125
C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125
C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2. ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Subgroups
per Method 5005, Table 1
Interim Electric Parameters
Method 5004
1
Final Electrical Parameters
Method 5005
1*, 2, 3
Group A Test Requirements
Method 5005
1, 2, 3
Group C and D End-Point Electrical Parameters
Method 5005
1
* PDA applies to Subgroup 1 only.
----------------------------
Electrical Characteristics of MX580S/T/U/883B
19-2445
Rev. B
for /883B and SMD 5962-86861
Page 4 of
5