2004 Microchip Technology Inc.
DS21227E-page 1
25AA320/25LC320/25C320
Device Selection Table
Features:
Low-power CMOS technology:
- Write current: 3 mA maximum
- Read current: 500
A typical
- Standby current: 500 nA typical
4096 x 8 bit organization
32 byte page
Write cycle time: 5 ms maximum
Self-timed erase and write cycles
Block write protection:
- Protect none, 1/4, 1/2 or all of array
Built-in write protection:
- Power on/off data protection circuitry
- Write enable latch
- Write-protect pin
Sequential read
High reliability:
- Endurance: 1M E/W cycles
- Data retention: > 200 years
- ESD protection: > 4000V
8-pin PDIP, SOIC and TSSOP packages
14-lead TSSOP package
Temperature ranges supported:
Description:
The Microchip Technology Inc. 25AA320/25LC320/
25C320 (25XX320
*
) are 32 Kbit serial Electrically
Erasable PROMs. The memory is accessed via a
simple Serial Peripheral Interface (SPITM) compatible
serial bus. The bus signals required are a clock input
(SCK) plus separate data in (SI) and data out (SO)
lines. Access to the device is controlled through a Chip
Select (CS) input.
Communication to the device can be paused via the
hold pin (HOLD). While the device is paused,
transitions on its inputs will be ignored, with the
exception of Chip Select, allowing the host to service
higher priority interrupts.
Block Diagram
Package Types
Part
Number
V
CC
Range
Max. Clock
Frequency
Temp.
Ranges
25AA320
1.8-5.5V
1 MHz
I
25LC320
2.5-5.5V
2 MHz
I,E
25C320
4.5-5.5V
3 MHz
I,E
- Industrial (I):
-40
C to
+85
C
- Automotive (E):
-40C to +125C
SI
SO
SCK
CS
HOLD
WP
Status
Register
I/O Control
Memory
Control
Logic
HV Generator
EEPROM
Array
Page
Y Decoder
Sense Amp.
R/W Control
Logic
V
CC
V
SS
Latches
XDEC
TSSOP
PDIP, SOIC
TSSOP
CS
SO
WP
V
SS
V
CC
HOLD
SCK
SI
1
2
3
4
8
7
6
5
25X
X320
HOLD
V
CC
CS
SO
1
2
3
4
8
7
6
5
SCK
SI
V
SS
WP
25X
X320
NC
CS
SO
NC
WP
V
SS
NC
NC
V
CC
HOLD
NC
SCK
SI
NC
25XX
320
1
2
3
4
14
13
12
11
5
10
9
7
8
6
32K SPI
TM
Bus Serial EEPROM
*25XX320 is used in this document as a generic part number for the 25AA320/25LC320/25C320 devices.
25AA320/25LC320/25C320
DS21227E-page 2
2004 Microchip Technology Inc.
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
()
V
CC
.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. V
SS
........................................................................................................ -0.6V to V
CC
+ 1.0V
Storage temperature .................................................................................................................................-65C to 150C
Ambient temperature under bias ...............................................................................................................-40C to 125C
ESD protection on all pins .......................................................................................................................................... 4 kV
TABLE 1-1:
DC CHARACTERISTICS
NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an
extended period of time may affect device reliability.
DC CHARACTERISTICS
Industrial (I):
T
A
= -40C to +85C
V
CC
= 1.8V to 5.5V
Automotive (E):T
A
= -40C to +125C V
CC
= 2.5V to 5.5V
Param.
No.
Sym.
Characteristics
Min.
Max.
Units
Conditions
D1
V
IH1
High-level input
voltage
2.0
V
CC
+1
V
V
CC
2.7V (Note)
D2
V
IH2
0.7 V
CC
V
CC
+1
V
V
CC
< 2.7V (Note)
D3
V
IL1
Low-level input
voltage
-0.3
0.8
V
V
CC
2.7V (Note)
D4
V
IL2
-0.3
0.3 V
CC
V
V
CC
< 2.7V (Note)
D5
V
OL
Low-level output
voltage
--
0.2
V
I
OL
= 1.0 mA, V
CC
< 2.5V
D6
V
OH
High-level output
voltage
V
CC
-0.5
--
V
I
OH
= -400
A
D7
I
LI
Input leakage current
--
1
A
CS = V
CC
, V
IN
= V
SS
TO
V
CC
D8
I
LO
Output leakage
current
--
1
A
CS = V
CC
, V
OUT
= V
SS
TO
V
CC
D9
C
INT
Internal Capacitance
(all inputs and
outputs)
--
7
pF
T
A
= 25C, CLK = 1.0 MHz,
V
CC
= 5.0V (Note)
D10
I
CC
Read Operating Current
--
--
1
500
mA
A
V
CC
= 5.5V; F
CLK
= 3.0 MHz;
SO = Open
V
CC
= 2.5V; F
CLK
= 2.0 MHz;
SO = Open
D11
I
CC
Write
--
--
5
3
mA
mA
V
CC
= 5.5V
V
CC
= 2.5V
D12
I
CCS
Standby Current
--
--
5
1
A
A
CS = V
CC
= 5.5V, Inputs tied to V
CC
or
V
SS
CS = V
CC
= 2.5V, Inputs tied to V
CC
or
V
SS
Note:
This parameter is periodically sampled and not 100% tested.
2004 Microchip Technology Inc.
DS21227E-page 3
25AA320/25LC320/25C320
TABLE 1-2:
AC CHARACTERISTICS
AC CHARACTERISTICS
Industrial (I):
T
A
= -40C to +85C
V
CC
= 1.8V to 5.5V
Automotive (E):
T
A
= -40C to +125C
V
CC
= 2.5V to 5.5V
Param.
No.
Sym.
Characteristic
Min.
Max.
Units
Conditions
1
F
CLK
Clock Frequency
--
--
--
3
2
1
MHz
MHz
MHz
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
2
T
CSS
CS Setup Time
100
250
500
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
3
T
CSH
CS Hold Time
150
250
475
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
4
T
CSD
CS Disable Time
500
--
ns
--
5
T
SU
Data Setup Time
30
50
50
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
6
T
HD
Data Hold Time
50
100
100
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
7
T
R
CLK Rise Time
--
2
s
(Note 1)
8
T
F
CLK Fall Time
--
2
s
(Note 1)
9
T
HI
Clock High Time
150
230
475
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
10
T
LO
Clock Low Time
150
230
475
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
11
T
CLD
Clock Delay Time
50
--
ns
--
12
T
CLE
Clock Enable Time
50
--
ns
--
13
T
V
Output Valid from
Clock Low
--
--
--
150
230
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
14
T
HO
Output Hold Time
0
--
ns
(Note 1)
15
T
DIS
Output Disable Time
--
--
--
200
250
--
ns
ns
ns
V
CC
= 4.5V to 5.5V (Note 1)
V
CC
= 2.5V to 5.5V (Note 1)
V
CC
= 1.8V to 5.5V
16
T
HS
HOLD Setup Time
100
100
200
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
17
T
HH
HOLD Hold Time
100
100
200
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
18
T
HZ
HOLD Low to Output
High-Z
100
150
200
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V (Note 1)
V
CC
= 2.5V to 5.5V (Note 1)
V
CC
= 1.8V to 5.5V
19
T
HV
HOLD High to Output
Valid
100
150
200
--
--
--
ns
ns
ns
V
CC
= 4.5V to 5.5V
V
CC
= 2.5V to 5.5V
V
CC
= 1.8V to 5.5V
20
T
WC
Internal Write Cycle
Time
--
5
ms
--
21
--
Endurance
1M
--
E/W
Cycles
(Note 2)
Note
1: This parameter is periodically sampled and not 100% tested.
2: This parameter is not tested but established by characterization. For endurance estimates in a specific application,
please consult the Total EnduranceTM Model which can be obtained from Microchip's web site at: www.microchip.com.
PDF 
ZIP
