MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
273
REV 6
Motorola, Inc. 1996
9/96
Dual 4 to 1 Multiplexer
The MC10H174 is a Dual 4to1 Multiplexer. This device is a functional/
pinout duplication of the standard MECL 10K part, with 100% improvement in
propagation delay and no increase in power supply current.
Propagation Delay, 1.5 ns Typical
Power Dissipation, 305 mW Typical
Improved Noise Margin 150 mV (over operating voltage and
temperature range)
Voltage Compensated
MECL 10KCompatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
VEE
8.0 to 0
Vdc
Input Voltage (VCC = 0)
VI
0 to VEE
Vdc
Output Current -- Continuous
-- Surge
Iout
50
100
mA
Operating Temperature Range
TA
0 to +75
C
Storage Temperature Range -- Plastic
-- Ceramic
Tstg
55 to +150
55 to +165
C
C
ELECTRICAL CHARACTERISTICS (VEE = 5.2 V
5%) (See Note)
0
25
75
Characteristic
Symbol
Min
Max
Min
Max
Min
Max
Unit
Power Supply Current
IE
--
80
--
73
--
80
mA
Input Current High
Pins 37 & 913
Pin 14
IinH
--
--
475
670
--
--
300
420
--
--
300
420
Adc
Input Current Low
IinL
0.5
--
0.5
--
0.3
--
A
High Output Voltage
VOH
1.02
0.84
0.98
0.81
0.92
0.735
Vdc
Low Output Voltage
VOL
1.95
1.63
1.95
1.63
1.95
1.60
Vdc
High Input Voltage
VIH
1.17
0.84
1.13
0.81
1.07
0.735
Vdc
Low Input Voltage
VIL
1.95
1.48
1.95
1.48
1.95
1.45
Vdc
AC PARAMETERS
Propagation Delay
Data
Select (A, B)
Enable
tpd
0.7
1.0
0.4
2.4
2.8
1.45
0.8
1.1
0.4
2.5
2.9
1.5
0.9
1.2
0.5
2.6
3.2
1.7
ns
Rise Time
tr
0.5
1.5
0.5
1.6
0.5
1.7
ns
Fall Time
tf
0.5
1.5
0.5
1.6
0.5
1.7
ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated
through a 50ohm resistor to 2.0 volts.
MC10H174
DIP
PIN ASSIGNMENT
VCC1
Q0
DO0
DO2
DO1
DO3
A
VEE
VCC2
Q1
ENABLE
D10
D12
D11
D13
B
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
TRUTH TABLE
ENABLE
ADDRESS INPUTS
OUTPUTS
X
X
E
B
A
Z
W
H
L
L
L
L
L
X0
Y0
L
L
H
X1
Y1
L
H
L
X2
Y2
L
H
H
X3
Y3
L SUFFIX
CERAMIC PACKAGE
CASE 62010
P SUFFIX
PLASTIC PACKAGE
CASE 64808
FN SUFFIX
PLCC
CASE 77502
Pin assignment is for DualinLine Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 611 of the Motorola MECL Data
Book (DL122/D).
MC10H174
275
MOTOROLA
MECL Data
DL122 -- Rev 6
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 77502
ISSUE C
NOTES:
1. DATUMS L, M, AND N DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM T, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
M
N
L
Y BRK
W
V
D
D
S
LM
M
0.007 (0.180)
N
S
T
S
LM
M
0.007 (0.180)
N
S
T
S
LM
S
0.010 (0.250)
N
S
T
X
G1
B
U
Z
VIEW DD
20
1
S
LM
M
0.007 (0.180)
N
S
T
S
LM
M
0.007 (0.180)
N
S
T
S
LM
S
0.010 (0.250)
N
S
T
C
G
VIEW S
E
J
R
Z
A
0.004 (0.100)
T
SEATING
PLANE
S
LM
M
0.007 (0.180)
N
S
T
S
LM
M
0.007 (0.180)
N
S
T
H
VIEW S
K
K1
F
G1
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.385
0.395
9.78
10.03
B
0.385
0.395
9.78
10.03
C
0.165
0.180
4.20
4.57
E
0.090
0.110
2.29
2.79
F
0.013
0.019
0.33
0.48
G
0.050 BSC
1.27 BSC
H
0.026
0.032
0.66
0.81
J
0.020
0.51
K
0.025
0.64
R
0.350
0.356
8.89
9.04
U
0.350
0.356
8.89
9.04
V
0.042
0.048
1.07
1.21
W
0.042
0.048
1.07
1.21
X
0.042
0.056
1.07
1.42
Y
0.020
0.50
Z
2
10
2
10
G1
0.310
0.330
7.88
8.38
K1
0.040
1.02
_
_
_
_
MC10H174
MOTOROLA
MECL Data
DL122 -- Rev 6
276
OUTLINE DIMENSIONS
P SUFFIX
PLASTIC DIP PACKAGE
CASE 64808
ISSUE R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
A
B
F
C
S
H
G
D
J
L
M
16 PL
SEATING
1
8
9
16
K
PLANE
T
M
A
M
0.25 (0.010)
T
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.740
0.770
18.80
19.55
B
0.250
0.270
6.35
6.85
C
0.145
0.175
3.69
4.44
D
0.015
0.021
0.39
0.53
F
0.040
0.70
1.02
1.77
G
0.100 BSC
2.54 BSC
H
0.050 BSC
1.27 BSC
J
0.008
0.015
0.21
0.38
K
0.110
0.130
2.80
3.30
L
0.295
0.305
7.50
7.74
M
0
10
0
10
S
0.020
0.040
0.51
1.01
_
_
_
_
L SUFFIX
CERAMIC DIP PACKAGE
CASE 62010
ISSUE V
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
A
B
T
F
E
G
N
K
C
SEATING
PLANE
16 PL
D
S
A
M
0.25 (0.010)
T
16 PL
J
S
B
M
0.25 (0.010)
T
M
L
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.750
0.785
19.05
19.93
B
0.240
0.295
6.10
7.49
C
0.200
5.08
D
0.015
0.020
0.39
0.50
E
0.050 BSC
1.27 BSC
F
0.055
0.065
1.40
1.65
G
0.100 BSC
2.54 BSC
H
0.008
0.015
0.21
0.38
K
0.125
0.170
3.18
4.31
L
0.300 BSC
7.62 BSC
M
0
15
0
15
N
0.020
0.040
0.51
1.01
_
_
_
_
16
9
1
8
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals"
must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; TatsumiSPDJLDC, 6F SeibuButsuryuCenter,
P.O. Box 20912; Phoenix, Arizona 85036. 18004412447 or 6023035454
3142 Tatsumi KotoKu, Tokyo 135, Japan. 038135218315
MFAX: RMFAX0@email.sps.mot.com TOUCHTONE 6022446609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://DesignNET.com
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 85226629298
MC10H174/D
*MC10H174/D*
PDF 
ZIP