1
Motorola Optoelectronics Device Data
6-Pin DIP Zero-Cross
Optoisolators Triac Driver Output
(600 Volts Peak)
The MOC3061, MOC3062 and MOC3063 devices consist of gallium arsenide
infrared emitting diodes optically coupled to monolithic silicon detectors
performing the functions of Zero Voltage Crossing bilateral triac drivers.
They are designed for use with a triac in the interface of logic systems to
equipment powered from 115/240 Vac lines, such as solidstate relays,
industrial controls, motors, solenoids and consumer appliances, etc.
Simplifies Logic Control of 115/240 Vac Power
Zero Voltage Crossing
dv/dt of 1500 V/
s Typical, 600 V/
s Guaranteed
To order devices that are tested and marked per VDE 0884 requirements, the
suffix "V" must be included at end of part number. VDE 0884 is a test option.
Recommended for 115/240 Vac(rms) Applications:
Solenoid/Valve Controls
Temperature Controls
Lighting Controls
E.M. Contactors
Static Power Switches
AC Motor Starters
AC Motor Drives
Solid State Relays
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
INFRARED EMITTING DIODE
Reverse Voltage
VR
6
Volts
Forward Current -- Continuous
IF
60
mA
Total Power Dissipation @ TA = 25
C
Negligible Power in Output Driver
Derate above 25
C
PD
120
1.41
mW
mW/
C
OUTPUT DRIVER
OffState Output Terminal Voltage
VDRM
600
Volts
Peak Repetitive Surge Current
(PW = 100
s, 120 pps)
ITSM
1
A
Total Power Dissipation @ TA = 25
C
Derate above 25
C
PD
150
1.76
mW
mW/
C
TOTAL DEVICE
Isolation Surge Voltage(1)
(Peak ac Voltage, 60 Hz, 1 Second Duration)
VISO
7500
Vac(pk)
Total Power Dissipation @ TA = 25
C
Derate above 25
C
PD
250
2.94
mW
mW/
C
Junction Temperature Range
TJ
40 to +100
C
Ambient Operating Temperature Range(2)
TA
40 to +85
C
Storage Temperature Range(2)
Tstg
40 to +150
C
Soldering Temperature (10 s)
TL
260
C
1. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating.
1.
For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common.
2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.
Preferred devices are Motorola recommended choices for future use and best overall value.
GlobalOptoisolator is a trademark of Motorola, Inc.
Order this document
by MOC3061/D
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
GlobalOptoisolator
TM
Motorola, Inc. 1995
MOC3061
MOC3062
MOC3063
*Motorola Preferred Device
COUPLER SCHEMATIC
[IFT = 15 mA Max]
STANDARD THRU HOLE
CASE 730A04
*
[IFT = 10 mA Max]
[IFT = 5 mA Max]
1. ANODE
2. CATHODE
3. NC
4. MAIN TERMINAL
5. SUBSTRATE
DO NOT CONNECT
6. MAIN TERMINAL
1
2
3
6
5
4
ZERO
CROSSING
CIRCUIT
6
1
STYLE 6 PLASTIC
(Replaces MOC3060/D)
MOC3061 MOC3062 MOC3063
2
Motorola Optoelectronics Device Data
ELECTRICAL CHARACTERISTICS
(TA = 25
C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
INPUT LED
Reverse Leakage Current
(VR = 6 V)
IR
--
0.05
100
A
Forward Voltage
(IF = 30 mA)
VF
--
1.3
1.5
Volts
OUTPUT DETECTOR (IF = 0)
Leakage with LED Off, Either Direction
(Rated VDRM(1))
IDRM1
--
60
500
nA
Critical Rate of Rise of OffState Voltage(3)
dv/dt
600
1500
--
V/
s
COUPLED
LED Trigger Current, Current Required to Latch Output
(Main Terminal Voltage = 3 V(2))
MOC3061
MOC3062
MOC3063
IFT
--
--
--
--
--
--
15
10
5
mA
Peak OnState Voltage, Either Direction
(ITM = 100 mA, IF = Rated IFT)
VTM
--
1.8
3
Volts
Holding Current, Either Direction
IH
--
250
--
A
Inhibit Voltage (MT1MT2 Voltage above which device will not trigger.)
(IF = Rated IFT)
VINH
--
5
20
Volts
Leakage in Inhibited State
(IF = Rated IFT, Rated VDRM, Off State)
IDRM2
--
--
500
A
Isolation Voltage (f = 60 Hz, t = 1 sec)
VISO
7500
--
--
Vac(pk)
1. Test voltage must be applied within dv/dt rating.
2. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended operating IF lies between max
2.
IFT (15 mA for MOC3061, 10 mA for MOC3062, 5 mA for MOC3063) and absolute max IF (60 mA).
3. This is static dv/dt. See Figure 7 for test circuit. Commutating dv/dt is a function of the loaddriving thyristor(s) only.
Figure 1. OnState Characteristics
3
VTM, ONSTATE VOLTAGE (VOLTS)
I
400
0
+400
+800
2
1
0
1
2
3
TM
, ONST
A
TE CURRENT
(mA)
600
800
200
+200
+600
4
4
0.7
Figure 2. Inhibit Voltage versus Temperature
40
TA, AMBIENT TEMPERATURE (
C)
0.8
1.1
1.3
20
0
20
40
60
80
, NORMALIZED
100
0.9
1
1.2
1.4
1.5
5
0.6
0.5
V
INH
NORMALIZED TO
TA = 25
C
OUTPUT PULSE WIDTH 80
s
IF = 30 mA
f = 60 Hz
TA = 25
C
TYPICAL CHARACTERISTICS
TA = 25
C
MOC3061 MOC3062 MOC3063
3
Motorola Optoelectronics Device Data
5
1
PWin, LED TRIGGER PULSE WIDTH (
s)
10
15
20
25
2
5
20
10
50
0
FTI
, NORMALIZED LED
TRIGGER CURRENT
NORMALIZED TO:
PWin
q
100
s
TA, AMBIENT TEMPERATURE (
C)
40
+400
Vdc
PULSE
INPUT
MERCURY
WETTED
RELAY
RTEST
CTEST
R = 10 k
X100
SCOPE
PROBE
D.U.T.
APPLIED VOLTAGE
WAVEFORM
252 V
0 VOLTS
t
RC
Vmax = 400 V
dv dt
+
0.63 Vmax
t
RC
+
378
t
RC
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
3. The worstcase condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
removing the current. The variable RTEST allows the dv/dt to be
gradually increased until the D.U.T. continues to trigger in
response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
the D.U.T. stops triggering.
t
RC is measured at this point and
recorded.
5
40
TA, AMBIENT TEMPERATURE (
C)
I
20
0
20
40
60
80
100
10
20
50
100
200
500
DRM1
, PEAK BLOCKING CURRENT
(nA)
0.6
40
TA, AMBIENT TEMPERATURE (
C)
I
IF = RATED IFT
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
20
0
20
40
60
80
100
DRM2
, NORMALIZED
I FT
, NORMALIZED
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
NORMALIZED TO
TA = 25
C
20
0
20
40
60
80
100
IF = 0
Figure 3. Leakage with LED Off
versus Temperature
Figure 4. IDRM2, Leakage in Inhibit State
versus Temperature
Figure 5. Trigger Current versus Temperature
Figure 6. LED Current Required to Trigger
versus LED Pulse Width
Figure 7. Static dv/dt Test Circuit
100
MOC3061 MOC3062 MOC3063
4
Motorola Optoelectronics Device Data
Rin
1
2
6
4
360
MOC306163
3
5
VCC
NOTE: This optoisolator should not be used to drive a load directly.
It is intended to be a trigger device only.
360
39
0.01
240 Vac
HOT
NEUTRAL
LOAD
Typical circuit for use when hot line switching is required.
In this circuit the "hot" side of the line is switched and the
load connected to the cold or neutral side. The load may be
connected to either the neutral or hot line.
Rin is calculated so that IF is equal to the rated IFT of the
part, 15 mA for the MOC3061, 10 mA for the MOC3062,
and 5 mA for the MOC3063. The 39 ohm resistor and 0.01
F capacitor are for snubbing of the triac and may or may
not be necessary depending upon the particular triac and
load used.
Rin
R1
2
6
4
3
5
VCC
R2
LOAD
360
D1
1
SCR
SCR
D2
240 Vac
Suggested method of firing two, backtoback SCR's,
with a Motorola triac driver. Diodes can be 1N4001; resis-
tors, R1 and R2, are optional 330 ohms.
Figure 8. HotLine Switching Application Circuit
Figure 9. InverseParallel SCR Driver Circuit
MOC306163
MOC3061 MOC3062 MOC3063
5
Motorola Optoelectronics Device Data
PACKAGE DIMENSIONS
CASE 730A04
ISSUE G
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
6
4
1
3
A
B
SEATING
PLANE
T
4 PL
F
K
C
N
G
6 PL
D
6 PL
E
M
A
M
0.13 (0.005)
B
M
T
L
M
6 PL
J
M
B
M
0.13 (0.005)
A
M
T
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.320
0.350
8.13
8.89
B
0.240
0.260
6.10
6.60
C
0.115
0.200
2.93
5.08
D
0.016
0.020
0.41
0.50
E
0.040
0.070
1.02
1.77
F
0.010
0.014
0.25
0.36
G
0.100 BSC
2.54 BSC
J
0.008
0.012
0.21
0.30
K
0.100
0.150
2.54
3.81
L
0.300 BSC
7.62 BSC
M
0
15
0
15
N
0.015
0.100
0.38
2.54
_
_
_
_
STYLE 6:
PIN 1. ANODE
2. CATHODE
3. NC
4. MAIN TERMINAL
5. SUBSTRATE
6. MAIN TERMINAL
CASE 730C04
ISSUE D
A
B
S
SEATING
PLANE
T
J
K
L
6 PL
M
B
M
0.13 (0.005)
A
M
T
C
D
6 PL
M
A
M
0.13 (0.005)
B
M
T
H
G
E
6 PL
F
4 PL
3
1
4
6
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.320
0.350
8.13
8.89
B
0.240
0.260
6.10
6.60
C
0.115
0.200
2.93
5.08
D
0.016
0.020
0.41
0.50
E
0.040
0.070
1.02
1.77
F
0.010
0.014
0.25
0.36
G
0.100 BSC
2.54 BSC
H
0.020
0.025
0.51
0.63
J
0.008
0.012
0.20
0.30
K
0.006
0.035
0.16
0.88
L
0.320 BSC
8.13 BSC
S
0.332
0.390
8.43
9.90
*Consult factory for leadform
option availability
MOC3061 MOC3062 MOC3063
6
Motorola Optoelectronics Device Data
*Consult factory for leadform
option availability
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
CASE 730D05
ISSUE D
6
4
1
3
A
B
N
C
K
G
F
4 PL
SEATING
D
6 PL
E
6 PL
PLANE
T
M
A
M
0.13 (0.005)
B
M
T
L
J
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.320
0.350
8.13
8.89
B
0.240
0.260
6.10
6.60
C
0.115
0.200
2.93
5.08
D
0.016
0.020
0.41
0.50
E
0.040
0.070
1.02
1.77
F
0.010
0.014
0.25
0.36
G
0.100 BSC
2.54 BSC
J
0.008
0.012
0.21
0.30
K
0.100
0.150
2.54
3.81
L
0.400
0.425
10.16
10.80
N
0.015
0.040
0.38
1.02
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different
applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; TatsumiSPDJLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 18004412447
6F SeibuButsuryuCenter, 3142 Tatsumi KotoKu, Tokyo 135, Japan. 0335218315
MFAX: RMFAX0@email.sps.mot.com TOUCHTONE (602) 2446609
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://DesignNET.com
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 85226629298
MOC3061/D
*MOC3061/D*
PDF 
ZIP