!
Applications: Wide Area Networks (WAN's)
Reference Clocking
!
Superior Tolerance Performance Including up to 10
years of aging
!
2.0 to 35.0 MHz Frequency Range
!
10ppm 20ppm Stability Options
!
-40C to 85C Operating Temperature - K1120D
!
0C to 70C Operating Temperature - K1110D
!
Meets Stratum IV Requirements
!
Enable/Disable Option Available
ELECTRICAL SPECIFICATIONS
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
K11X0DA
33.33
0 MHZ
CTI DA
TE CODE
7,49 m
m M
ax.
20,8 mm Max.
13,2 mm Max.
PIN 1
1
Model
K1110DA
Frequency Range (MHz)
Input Current (mA)
2 to 35
< 30
Frequency Stability (ppm)
Overall
Temperature Range (oC)
Inclusive of Calibration, Temperature, Voltage, Load, Aging
Operating
Storage
0oC to +70oC
-40oC to +85oC
Supply Voltage (V)
Start Up Time (ms)
+5.0V 5%
<10
-40oC to 85oC
Symmetry CMOS/TTL
45/55 < 16MHz; 40/60
16MHz
-
Aging @ 50oC (10 Years)
Inclusive
K1110D & K1120D Series
5V Crystal Clock Oscillators
K1120DAM
0oC to 70oC
10
-
20
3.0
-40oC to +85oC
PART NUMBERING GUIDE
K11X0DAX X - Specify Frequency
"Blank" = Fixed Frequency
"E" = Enable/Disable
"Blank" = 0C to 70C Operating Temp.
"M" = -40C to +85C Operating Temp.
Model Selection: See Table Above
0.5 max.
4.5 min
< 5
"0" Level (VOL)
"1" Level (VOH)
Rise Time & Fall Time (ns)
PIN
FUNCTION
N/C or Enable/Disable
1
7
8
14
Gnd/ & Case Gnd
Output
+ VCC
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
K1110D & K1120D Series
5V Crystal Clock Oscillators
2
SHIPPING TUBE CROSS SECTION
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
Mechanical Shock
MIL-STD-202, Mtd 213, Cond. D
-55C to +125C; Air-to-Air; 100 cycles; 10
min. dwell
Vibration
MIL-STD 202, Mtd 204, Cond. B
10-2000 Hz; 0.06 inch; 15g; 3 planes
Humidity Steady State
MIL-STD-202, Mtd 103
40C; 90%-95% R.H.; 56 days
Thermal Shock
MIL-STD-883, Mtd 1011.7 Cond. A
Electrostatic Discharge
Solderability
Hermeticity
Resistance to Soldering
Lead Integrity
Marking Permanence
Life Test
100C to 0C; Water-to-Water; 15 cycles
2 KV to 4 KV Threshold
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
260C; 10 seconds: 1 inch/sec.
Lead tension & bend stress
Resistance to solvents
500 g's
MIL-STD-883, Mtd 3015 Class II
MIL-STD-883, Mtd 1005.6
MIL-STD-883, Mtd 2022.2
MIL-STD-883, Mtd 1014.8, Cond. A1
MIL-STD-202, Mtd 210A, Cond. C
MIL-STD-883, Mtd 2004.5, Cond. A, B1
MIL-STD-883, Mtd 2015.8
125
C, powered, 1000 hours minimum
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
OUTPUT WAVEFORM
TEST CIRCUIT DIAGRAM
PDF 
ZIP