ChipFind - документация

Электронный компонент: K1526A

Скачать:  PDF   ZIP
!
Applications: Phase-Locked Loops (PLL's); Clock Recovery;
Reference Signal Tracking;Synthesizers; Frequency
Modulation/Demodulation
!
Ceramic Construction, Medal Lid
!
2.0 to 40 MHz Frequency Range
!
0.5V to 4.5V Control Voltage
!
25ppm Stability
!
-40C to 85C Operating Temperature Option
!
Tape and Reel Available
!
Ground Shielded Top and Bottom 4-Pin SOJ-20 Footprint
!
J-Leads Seam-sealed, Resistance Welded Hermetic Package
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
1
MODEL
K1526AA
Frequency Range (MHz)
2 to 33
Frequency Stability (ppm)
Overall
Inclusive of calibration, temperature, voltage, load, shock,vibration, aging
0C to 70C
25
-40C to +85C
50
Frequency Control Function:
(for custom deviation range, Vc range, transfer function, etc. -- consult factory)
Deviation (ppm)
Minimum
100
Linearity
Control Voltage Range (V)
0.5 to 4.5
Transfer Function
Positive
Input Impedance
>50 K Ohms @ 10 KHz
Temperature Range (C)
Operating
-40C to +85C
Storage
-40C to +125C
Supply Voltage (V)
+5.0 10%
Input Current (mA)
<26
Start Up Time (ms)
<10
Symmetry (%) TTL
45/55
Symmetry (%) CMOS
<33 MHz 45/55;
33 MHz 40/60
ELECTRICAL SPECIFICATIONS
Start up Time (ms)
<10
Typical SSB Phase Noise (dBc/Hz)
Offset from Carrier
10Hz
100Hz
1KHz
10KHz
100KHz
<5%
PART NUMBERING GUIDE
K1526AX X - Specify Frequency
"Blank" = 0C to 70C Operating Temp.
"M" = -40C to +85C Operating Temp.
Model Selection: See Table Above
K1526AD
33.1 to 40
2 to 33
33.1 to 40
<10%
40
60
80
<5%
-65
-95
-120
-140
-150
K1526A Series
5V 9x14mm Surface Mount Voltage Controlled Crystal Oscillators
Not Recommended for New Designs. Refer
to K1526D Series as an Alternative.
Maximum
150
120
<20KHz
2.5
Modulation Bandwidth (3dB)
Nominal Control Voltage (V)
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
2
OUTPUT WAVEFORM
TEST CIRCUIT DIAGRAM
PIN
FUNCTION
Voltage Control
1
2
3
4
Gnd & Ground Plane
Output
+ VCC
Tape & Reel
Shipping Tape
Size: 24mm
Material: Black PVC,
Conductive .012 thick
Shipping Reel
Size: 13 diameter
Material: Plastic
13 Reel
Tape Length 16.5 yds
Max. No. of Pockets:750
Leader Length: 16 min.
Trailer Length: 14 min.
Q.C. Sample Quantity: 10 pcs.
Product/Reel: 500
Cover Tape Thickness: .002
Cover Peel Strength: 75g
Note: Minimum Order is 500
SHIPPING TUBE CROSS SECTION
TAPE & REEL SPECIFICATIONS
K1526A Series
5V 9x14mm Surface Mount Voltage Controlled Crystal Oscillators
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
Mechanical Shock
MIL-STD-883, Mtd 2002, Cond. B
-55C to +125C; Air-to-Air; 100 cycles; 10
min. dwell
Vibration
MIL-STD 883, Mtd 2007, Cond. B
20-2000 Hz; 0.06 inch; 15g's; 3 planes
Humidity Steady State
MIL-STD-202, Mtd 103
40C; 90%-95% R.H.; 56 days
Thermal Shock
MIL-STD-883, Mtd 1011.7 Cond. B
Electrostatic Discharge
Solderability
Hermeticity
Resistance to Soldering
Lead Integrity
Marking Permanence
Life Test
100C to 0C; Water-to-Water; 15 cycles
2 KV to 4 KV Threshold
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
235C; 30 seconds
Lead tension & bend stress
Resistance to solvents
1500 g's
MIL-STD-883, Mtd 3015 Class II
MIL-STD-883, Mtd 1005.6
MIL-STD-883, Mtd 2022.2
MIL-STD-883, Mtd 1014.8, Cond. A1
MIL-STD-202, Mtd 210D, Cond. J
MIL-STD-883, Mtd 2004.5, Cond. A, B1
MIL-STD-883, Mtd 2015.8
125
C, powered, 1000 hours minimum
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS