Applications: Phase Locked Loops Clocking
"Sync" to NTSC Video Standards; Reference
Signal; Signal Tracking
10ppm Stability
-40C to 85C Op. Temperature
"Clipped" Sine Wave Output
Non Hermetic Package
ELECTRICAL SPECIFICATIONS
2553 N. Edgington Street, Franklin Park, IL 60131 Phone: 847.451.1000 Fax: 847.451.7585
800-888-1499 or www.champtech.com
1
Model
K1610
Frequency Range (MHz)
Input Current (mA)
1 to 27
< 2
Frequency Control Function
Frequency Stability (ppm)
Overall
Temperature Range (oC)
10ppm
(Inclusive of Calibration, Temperature, Voltage, Load and 10 yr.Aging)
Operating
Storage
-40oC to +85oC
Supply Voltage (V)
Start Up Time (ms)
+5V 5%
<10
(For Custom Deviation Range, Vc Range, etc. - Consult Factory)
Output ("Clipped" Sine Wave)
1.0V p-p min., 10K
/10pF
-40oC to +85oC
PART NUMBERING GUIDE
K1610 - Specify Frequency
K1610 Series
5V Voltage Controlled Temperature Compensated Crystal Oscillators
25oC Calibration
Over Operating Temperature
1ppm
3ppm
Aging 1st Year
1ppm
Voltage Control
Included
Minimum Deviation (ppm)
28
Modulation Bandwidth (3dB)
Control Voltage Range (V)
Transfer Function
Positive
0.5 to 4.5
Input Impedance
> 50K
@ 10KHz
Minimum Deviation Sensitivity (ppm/V)
+14
> 20KHz
Linearity (%)
<10
Nominal Control Voltage (V)
2.5
Typical SSB Phase Noise (dBC/Hz)
Offset From Carrier
-70
10Hz
100Hz
-95
1KHz
-120
10KHz
-140
100KHz
-150
Manual Adjustment (ppm)
5 min.
PIN
FUNCTION
Voltage Control
1
7
8
14
Gnd/ & Case Gnd
Output
+ VCC
2553 N. Edgington Street, Franklin Park, IL 60131 Phone: 847.451.1000 Fax: 847.451.7585
800-888-1499 or www.champtech.com
2
K1610 Series
5V Voltage Controlled Temperature Compensated Crystal Oscillators
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
Mechanical Shock
MIL-STD-883, Mtd 2002, Cond. B
-55C to +125C; Air-to-Air; 100 cycles; 10
min. dwell
Vibration
MIL-STD 883, Mtd 2007, Cond. B
20-2000 Hz; 0.06 inch; 15g's; 3 planes
Humidity Steady State
MIL-STD-202, Mtd 103
40C; 90%-95% R.H.; 56 days
Thermal Shock
MIL-STD-883, Mtd 1011.7 Cond. B
Electrostatic Discharge
Solderability
Hermeticity
Resistance to Soldering
Lead Integrity
Marking Permanence
Life Test
100C to 0C; Water-to-Water; 15 cycles
2 KV to 4 KV Threshold
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
260C; 10 seconds: 1 inch/sec.
Lead tension & bend stress
Resistance to solvents
1500 g's
MIL-STD-883, Mtd 3015 Class II
MIL-STD-883, Mtd 1005.6
MIL-STD-883, Mtd 2022.2
MIL-STD-883, Mtd 1014.8, Cond. A1
MIL-STD-202, Mtd 210A, Cond. C
MIL-STD-883, Mtd 2004.5, Cond. A, B1
MIL-STD-883, Mtd 2015.8
125
C, powered, 1000 hours minimum
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
TEST CIRCUIT DIAGRAM
PDF 
ZIP