357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email:
nelsales@nelfc.com
www.nelfc.com
Differential Positive ECL (DPECL)
SD-B2980 Series
Description
The SD-B2980 Series of quartz crystal oscillators provide DPECL compatible signals. Systems designers
may now specify space-saving, cost-effective packaged PECL oscillators to meet their timing requirements.
Features
Wide frequency range100.0MHz to 160.0MHz
User specified tolerance available
Will withstand vapor phase temperatures of 253C
for 4 minutes maximum
Space-saving alternative to discrete component
oscillators
High shock resistance, to 1000g
2.5 volt operation
High Reliability - NEL HALT/HASS qualified for
crystal oscillator start-up conditions
Wavecrest jitter characterization available
Overtone technology
High Q Crystal actively tuned oscillator circuit
No internal PLL avoids cascading PLL problems
Metal lid electrically connected to ground to
reduce EMI
Gold plated pads
Electrical Connection
Pin Connection
1 Enable/Disable
2 N.C.
3 V
EE
/Ground
4 Output
5 /Output
6 V
CC
CRYSTAL CLOCK OSCILLATORS
Data Sheet 0306A
Rev. B
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email:
nelsales@nelfc.com
www.nelfc.com
SD-B2980 Series Continued
Differential Positive ECL (DPECL)
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter
Symbol
Conditions
Min
Typical
Max
Frequency
-----
-----
100.0MHz -----
160.0MHz
Duty Cycle -----
@ V
CC
-1.29V
40/60% -----
60/40%
Logic 0
(2)
V
OL
-----
V
CC
-1.95V -----
V
CC
-1.60V
Logic 1
(2)
V
OH
-----
V
CC
-1.02V -----
V
CC
-0.74V
Rise & Fall Time
tr,tf 20-80%V
O
with 50 ohm load to V
CC
-2V ----- -----
1 nsec
Jitter, RMS
(3)
-----
-----
-----
-----
3 psec
Enable Voltage
(5)
-----
with V
EE
= 0V
V
CC
-0.4V
-----
-----
Disable Voltage
-----
with V
EE
= 0V
-----
-----
0.4V
Frequency Stability
(1)
dF/F
Overall conditions including:
-100ppm
-----
+100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration
General Characteristics
Parameter
Symbol
Conditions
Min
Typical
Max
Supply Voltage
V
CC
-----
2.45V 2.5V
2.55V
Supply Current
I
CC
50 ohm termination
0.0 mA
-----
80 mA
To 2.00V below V
CC
Output current
I
O
Low level Output Current 0.0 mA -----
50.0 mA
Operating temperature
T
A
------
0C -----
70C
Storage temperature
T
S
----- -55C -----
125C
Power Dissipation
P
D
-----
-----
-----
276 mW
Lead temperature
T
L
Soldering, 10 sec. ----- -----
300C
Load
50 Ohm to V
CC
-2V or Thevenin Equivalent, Bias Required
Start-up time
t
S
-----
-----
2 ms
10 ms
Environmental and Mechanical Characteristics
Mechanical Shock
Per MIL-STD-202, Method 213, Condition E
Thermal Shock
Per MIL-STD-833, Method 1011, Condition A
Vibration
0.060" double amplitude 10 Hz to 55 Hz, 35g's 55Hz to 2000 Hz
Soldering Condition
300C for 10 seconds
Hermetic Seal
Leak rate less than 1 x 10
-8
atm.cc/sec of helium
Footnotes:
1) Standard frequency stability (20,25,50ppm & others available)
2) V
OL
, V
OH
, referenced to ground (V
EE
) with V
CC
= 2.5V
3) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization.
5) Open to enable pin also enables the output.
Rev. B
CRYSTAL CLOCK OSCILLATORS
SD - B298X - FREQ
Package Code
Tolerance/Performance
SD 6 pad 5x7mm SMD
0 100ppm 0-70C
1 50ppm 0-70C
7 25ppm 0-70C
Input Voltage
9 Customer Specific
Code Specification
A 20ppm 0-70C
A 3.3V
B 50ppm -40 to +85C
B 2.5V
C 100ppm -40 to +85C
5V
Creating a Part Number
Data Sheet 0306A
PDF 
ZIP