NHI 6033
NATIONAL HYBRID INC.
RONKONKOMA, NY 11779
Miniature, Hermetically Sealed
Darlington Optocoupler
NHI 6033
Features;
-55c to +125c Operation
Output Voltage to 30V
Input Current from < 0.2mA
Low Output Saturation Typ < 1.0V
Withstanding Voltage > 1500Vd0
High Radiation Tolerance
Functionally Compatible with 4N33
Absolute Maximum Ratings;
Supply Voltage (Vcc) ......................................... -0.5 to 30Vdc
Continuous Input Current .................................... 60mA
Peak Input Current If (10uS,300Hz) ....................... 3A
Reverse Input Voltage Vr .................................... 5 Vdc
Led Power Dissipation (At Tc=25c)....................... 100mW
Output Current .................................................. 100mA
Output Voltage ..................................................-0.5 to 30Vdc
Output Power Dissipation .................................... 300mW
Storage Temperature ......................................... -65C to 150C
Lead Solder Temperature .................................... 260C for 10 sec.
Recommended Operating Conditions;
Output Voltage Range .................................................... to 30Vdc
Input Current ................................................................... 0.5 mA to 15mA
Ambient Operating Temperature Range ........................ -55C to 125C
Electrical Performance Characteristics;
Terminal
Number
Terminal
Function
1
ANODE
2
CATHODE
3
EMITTER
4
COLLECTOR
Page1
1
2
4
3
ANODE
CATHODE
COLLECTOR
EMITTER
NHI-6033
NHI 6033
TEST
SYM-
BOL
TEST CONDITIONS
GROUP
A SUB-
GROUP
LIMITS
MIN MAX
UNITS
Current Transfer Ratio
Ctr
Vce = 10V, If =1mA (at Ta = 25C) _1
Vce = 10V, If =1mA (at Ta = -55C) _1
Vce = 10V, If =1mA (at Ta = 125C)_1
1,2,3
500
500
200
%
Collector-Emitter
Breakdown Voltage
Vceo Ic = 100uA
30 60
Vdc
Emitter Collector
Breakdown
Veco Ie = 100Ua
5.0 7.5
Vdc
Output Saturation
Voltage
Vce
(sat)
If= 8mA , Ic=2.0mA
1,2.3
1.0
Vdc
High Level Output
Current (dark current) Iceo Vcc = 10V, If = 0A
1,2,3
100
nAdc
Input Forward Voltage Vf
If = 10mA
1,2
1.7
Vdc
Input Reverse Break-
down Voltage
Vbr
Ir = 10A
1,2,3
5.0 30 Vdc
Turn on time
Ton If = 200mA, Ic = 50mA, Vcc = 10V
9,10,11
5.0
uS
Turn-off time
Toff
If = 200mA, Ic = 50mA, Vcc = 10V
9,10,11
100 uS
Page2
NHI 6033
TEST
SYM-
BOL
CONDITIONS
GROUP
A SUB-
GROUP
LIMITS
MIN
UNITS
Capacitance,
input to output
Cio
f = 1Mhz, Ta = 25C _ 3_4
4
4
pF
Common Mode
Transient Immunity,
high output
Cmh
Vcm = 25v (peak)
Vcc = 5.0v, Rl = 2.0K _4_5_7
If = 0mA,
9,10,11
500
V/s
Common Mode
Transient Immunity,
lo output
Cml
Vcm = 25v (peak)
Vcc = 5.0v, Rl = 2.0K _4_6_7
If = 0mA,
9,10,11
500
V/s
Isolation Voltage
Viso Ii-o 1uA _2_4
1500
Vdc
_1 Ctr is defined as the ratio of the Output Collector current (Io) to the LED Forward Current ( If ), times 100%.
_2 Device is considered a two terminal device. Pins 1 and 2 are shorted together and pins 4 and 5 are shorted
together.
_3 Measured between the LED cathode and pins 4 and 5 (shorted together).
_4 Parameters shall be tested as part of the device's initial characterization . Parameters are guaranteed to the limits
specified for all lots not specifically tested.
_5 Cmh is the maximum common mode transient to assure that the output will remain in a high logic state (Vo > 2.0V).
_6 Cml is the maximum common mode transient to assure that the output will remain in a low logic state (Vo < 0.8V).
_7 In applications where dV/dt may exceed 50,000 Vs a series resistor must be included in the Vcc line to limit
destructively high surge currents. The recomended value, at If = 0.5mA, is 3.3K
Notes;
Page3
Isolation Characteristics:
(at Ta = 25C unless otherwise specified)
NHI 6033
Page4
Fig 1 Switching Time Test Circuit
Fig 2 Common Mode Test circuit
Fig 3 Switching Time Test Waveform
Fig 4 Common Mode Test Waveform
NHI 6033
Page5
TYPICAL P.C. PATTERN
0.160
0.075 MAX
0.110 MAX
0.032
PIN 1
0.050
0.035
PIN 1
PIN 1
0.120
0.120
LEADLESS
OPTION (-Z)
GULLWING
OPTION (-X)
0.035
0.04
0.16
2.2984
0.025
PDF 
ZIP