LM2830
High Frequency 1.0A Load - Step-Down DC-DC
Regulator
General Description
The LM2830 regulator is a monolithic, high frequency, PWM
step-down DC/DC converter in a 5 pin SOT23 and a 6 Pin
LLP package. It provides all the active functions to provide
local DC/DC conversion with fast transient response and
accurate regulation in the smallest possible PCB area. With
a minimum of external components, the LM2830 is easy to
use. The ability to drive 1.0A loads with an internal 130 m
PMOS switch using state-of-the-art 0.5 m BiCMOS technol-
ogy results in the best power density available. The world-
class control circuitry allows on-times as low as 30ns, thus
supporting exceptionally high frequency conversion over the
entire 3V to 5.5V input operating range down to the minimum
output voltage of 0.6V. Switching frequency is internally set
to 1.6 MHz, or 3.0 MHz, allowing the use of extremely small
surface mount inductors and chip capacitors. Even though
the operating frequency is high, efficiencies up to 93% are
easy to achieve. External shutdown is included, featuring an
ultra-low stand-by current of 30 nA. The LM2830 utilizes
current-mode control and internal compensation to provide
high-performance regulation over a wide range of operating
conditions. Additional features include internal soft-start cir-
cuitry to reduce inrush current, pulse-by-pulse current limit,
thermal shutdown, and output over-voltage protection.
Features
n
Space Saving SOT23-5 Package
n
Input voltage range of 3.0V to 5.5V
n
Output voltage range of 0.6V to 4.5V
n
1.0A output current
n
High Switching Frequencies
1.6MHz (LM2830X)
3.0MHz (LM2830Z)
n
130m
PMOS switch
n
0.6V, 2% Internal Voltage Reference
n
Internal soft-start
n
Current mode, PWM operation
n
Thermal Shutdown
n
Over voltage protection
Applications
n
Local 5V to Vcore Step-Down Converters
n
Core Power in HDDs
n
Set-Top Boxes
n
USB Powered Devices
n
DSL Modems
Typical Application Circuit
20197464
20197481
August 2006
LM2830
High
Frequency
1.0A
Load
-
Step-Down
DC-DC
Regulator
2006 National Semiconductor Corporation
DS201974
www.national.com
Connection Diagrams
20197401
6-Pin LLP
20197403
5-Pin SOT-23
Ordering Information
Order Number
Frequency
Option
Package Type
NSC Package
Drawing
Top Mark
Supplied As
LM2830XMF
1.6MHz
SOT23-5
MF05A
SKTB
1000 units Tape and Reel
LM2830XMFX
3000 units Tape and Reel
LM2830ZMF
3MHz
SOT23-5
MF05A
SKXB
1000 units Tape and Reel
LM2830ZMFX
3000 units Tape and Reel
LM2830ZSD
LLP-6
SDE06A
L192B
1000 units Tape and Reel
LM2830ZSDX
4500 units Tape and Reel
NOPB versions available as well
LM2830
www.national.com
2
Pin Descriptions 5-Pin SOT23
Pin
Name
Function
1
SW
Output switch. Connect to the inductor and catch diode.
2
GND
Signal and power ground pin. Place the bottom resistor of the feedback network as close as
possible to this pin.
3
FB
Feedback pin. Connect to external resistor divider to set output voltage.
4
EN
Enable control input. Logic high enables operation. Do not allow this pin to float or be
greater than VIN + 0.3V.
5
VIN
Input supply voltage.
Pin Descriptions 6-Pin LLP
Pin
Name
Function
1
FB
Feedback pin. Connect to external resistor divider to set output voltage.
2
GND
Signal and power ground pin. Place the bottom resistor of the feedback network as
close as possible to this pin.
3
SW
Output switch. Connect to the inductor and catch diode.
4
VIND
Power Input supply.
5
VINA
Control circuitry supply voltage. Connect VINA to VIND on PC board.
6
EN
Enable control input. Logic high enables operation. Do not allow this pin to float or be
greater than VINA + 0.3V.
DAP
Die Attach Pad
Connect to system ground for low thermal impedance, but it cannot be used as a
primary GND connection.
LM2830
www.national.com
3
Absolute Maximum Ratings
(Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
VIN
-0.5V to 7V
FB Voltage
-0.5V to 3V
EN Voltage
-0.5V to 7V
SW Voltage
-0.5V to 7V
ESD Susceptibility
2kV
Junction Temperature (Note 2)
150C
Storage Temperature
-65C to +150C
Soldering Information
Infrared or Convection Reflow
(15 sec)
220C
Operating Ratings
VIN
3V to 5.5V
Junction Temperature
-40C to +125C
Electrical Characteristics
VIN = 5V unless otherwise indicated under the Conditions column. Limits in
standard type are for T
J
= 25C only; limits in boldface type apply over the junction temperature (T
J
) range of -40C to
+125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at T
J
= 25C, and are provided for reference purposes only.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
FB
Feedback Voltage
LLP-6 and SOT23-5
Package
0.588
0.600
0.612
V
V
FB
/V
IN
Feedback Voltage Line Regulation
V
IN
= 3V to 5V
0.02
%/V
I
B
Feedback Input Bias Current
0.1
100
nA
UVLO
Undervoltage Lockout
V
IN
Rising
2.73
2.90
V
V
IN
Falling
1.85
2.3
UVLO Hysteresis
0.43
V
F
SW
Switching Frequency
LM2830-X
1.2
1.6
1.95
MHz
LM2830-Z
2.25
3.0
3.75
D
MAX
Maximum Duty Cycle
LM2830-X
86
94
%
LM2830-Z
82
90
D
MIN
Minimum Duty Cycle
LM2830-X
5
%
LM2830-Z
7
R
DS(ON)
Switch On Resistance
LLP-6 Package
150
m
SOT23-5 Package
130
195
I
CL
Switch Current Limit
V
IN
= 3.3V
1.2
1.75
A
V
EN_TH
Shutdown Threshold Voltage
0.4
V
Enable Threshold Voltage
1.8
I
SW
Switch Leakage
100
nA
I
EN
Enable Pin Current
Sink/Source
100
nA
I
Q
Quiescent Current (switching)
LM2830X V
FB
= 0.55
3.3
5
mA
LM2830Z V
FB
= 0.55
4.3
6.5
mA
Quiescent Current (shutdown)
All Options V
EN
= 0V
30
nA
LM2830
www.national.com
4
Electrical Characteristics
VIN = 5V unless otherwise indicated under the Conditions column. Limits in
standard type are for T
J
= 25C only; limits in boldface type apply over the junction temperature (T
J
) range of -40C to
+125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at T
J
= 25C, and are provided for reference purposes only. (Continued)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
JA
Junction to Ambient
0 LFPM Air Flow (Note 3)
LLP-6 Package
80
C/W
SOT23-5 Package
118
JC
Junction to Case (Note 3)
LLP-6 Package
18
C/W
SOT23-5 Package
80
T
SD
Thermal Shutdown Temperature
165
C
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for which the device is
intended to be functional, but does not guarantee specfic performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Thermal shutdown will occur if the junction temperature exceeds the maximum junction temperature of the device.
Note 3: Applies for packages soldered directly onto a 3" x 3" PC board with 2oz. copper on 4 layers in still air.
LM2830
www.national.com
5
PDF 
ZIP