LM4929
Stereo 40mW Low Noise Headphone Amplifier
with OCL Output
General Description
The LM4929 is an stereo audio power amplifier capable of
delivering 40mW per channel of continuous average power
into a 16
load or 25mW per channel into a 32 load at 1%
THD+N from a 3V power supply.
Boomer audio power amplifiers were designed specifically to
provide high quality output power with a minimal amount of
external components. Since the LM4929 does not require
bootstrap capacitors or snubber networks, it is optimally
suited for low-power portable systems. The LM4929 is con-
figured for OCL (Output Capacitor-Less) outputs, operating
with no DC blocking capacitors on the outputs.
The LM4929 features a low-power consumption shutdown
mode with a faster turn on time. Additionally, the LM4929
features an internal thermal shutdown protection mecha-
nism.
The LM4929 is unity gain stable and may be configured with
external gain-setting resistors.
Key Specifications
j
PSRR at 217Hz and 1kHz
65dB (typ)
j
Output Power at 1kHz with V
DD
= 2.4V,
1% THD+N into a 16
load
25mW (typ)
j
Output Power at 1kHz with V
DD
= 3V,
1% THD+N into a 16
load
40mW (typ)
j
Shutdown current
2.0A (max)
j
Output Voltage change on release
from Shutdown V
DD
= 2.4V, R
L
= 16
1mV (max)
Features
n
OCL outputs -- No DC Blocking Capacitors
n
External gain-setting capability
n
Available in space-saving MSOP package
n
Ultra low current shutdown mode
n
2V - 5.5V operation
n
Ultra low noise
Applications
n
Portable CD players
n
PDAs
n
Portable electronics devices
Block Diagram
Boomer
is a registered trademark of National Semiconductor Corporation.
20132441
FIGURE 1. Block Diagram
December 2004
LM4929
Stereo
40mW
Low
Noise
Headphone
Amplifier
with
OCL
Output
2004 National Semiconductor Corporation
DS201324
www.national.com
Absolute Maximum Ratings
(Note 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage
6.0V
Storage Temperature
-65C to +150C
Input Voltage
-0.3V to V
DD
+ 0.3V
Power Dissipation (Note 3)
Internally Limited
ESD Susceptibility (Note 4)
2000V
ESD Susceptibility (Note 5)
200V
Junction Temperature
150C
Thermal Resistance
JC
(MSOP)
56C/W
JA
(MSOP)
190C/W
Operating Ratings
Temperature Range
T
MIN
T
A
T
MAX
-40C
T
A
85C
Supply Voltage
2V
V
DD
5.5V
Electrical Characteristics V
DD
= 5V
(Notes 1, 2)
The following specifications apply for V
DD
= 5V, R
L
= 16
, and C
B
= 4.7F unless otherwise specified. Limits apply to T
A
=
25C. Pin 3 connected to GND.
Symbol
Parameter
Conditions
LM4929
Units
(Limits)
Typ
(Note 6)
Limit
(Note 7)
I
DD
Quiescent Power Supply Current
V
IN
= 0V, I
O
= 0A
2
5
mA (max)
I
SD
Shutdown Current
V
SHUTDOWN
= GND
0.1
2.0
A(max)
V
SDIH
Shutdown Voltage Input High
1.8
V
V
SDIL
Shutdown Voltage Input Low
0.4
V
P
O
Output Power
THD = 1%; f = 1 kHZ
mW
R
L
= 16
80
R
L
= 32
80
V
NO
Output Noise Voltage
BW = 20Hz to 20kHz, A-weighted
10
V
PSRR
Power Supply Rejection Ratio
V
RIPPLE
= 200mV sine p-p
65
dB
Electrical Characteristics V
DD
= 3.0V
(Notes 1, 2)
The following specifications apply for V
DD
= 3.0V, R
L
= 16
, and C
B
= 4.7F unless otherwise specified. Limits apply to T
A
=
25C. Pin 3 connected to GND.
Symbol
Parameter
Conditions
LM4929
Units
(Limits)
Typ
(Note 6)
Limit
(Note 7)
I
DD
Quiescent Power Supply Current
V
IN
= 0V, I
O
= 0A
1.5
3.5
mA (max)
I
SD
Shutdown Current
V
SHUTDOWN
= GND
0.1
2.0
A(max)
P
O
Output Power
THD = 1%; f = 1kHz
mW
R = 16
40
R = 32
25
V
NO
Output Noise Voltage
BW = 20 Hz to 20kHz, A-weighted
10
V
PSRR
Power Supply Rejection Ratio
V
RIPPLE
= 200mV sine p-p
65
dB
Electrical Characteristics V
DD
= 2.4V
(Notes 1, 2)
The following specifications apply for V
DD
= 2.4V, R
L
= 16
, and C
B
= 4.7F unless otherwise specified. Limits apply to T
A
=
25C. Pin 3 connected to GND.
Symbol
Parameter
Conditions
LM4929
Units
(Limits)
Typ
(Note 6)
Limit
(Note 7)
I
DD
Quiescent Power Supply Current
V
IN
= 0V, I
O
= 0A
1.5
3
mA (max)
I
SD
Shutdown Current
V
SHUTDOWN
= GND
0.1
2.0
A(max)
P
O
Output Power
THD = 1%; f = 1kHz
mW
R = 16
25
R = 32
12
LM4929
www.national.com
3
Electrical Characteristics V
DD
= 2.4V
(Notes 1, 2) (Continued)
The following specifications apply for V
DD
= 2.4V, R
L
= 16
, and C
B
= 4.7F unless otherwise specified. Limits apply to T
A
=
25C. Pin 3 connected to GND.
Symbol
Parameter
Conditions
LM4929
Units
(Limits)
Typ
(Note 6)
Limit
(Note 7)
V
NO
Output Noise Voltage
BW = 20 Hz to 20kHz, A-weighted
10
V
PSRR
Power Supply Rejection Ratio
V
RIPPLE
= 200mV sine p-p
65
dB
T
WU
Wake Up Time from Shutdown
OCL
0.5
s
Note 1: All voltages are measured with respect to the GND pin unless otherwise specified.
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3: : The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX,
JA
, and the ambient temperature, T
A
. The
maximum allowable power dissipation is P
DMAX
= (T
JMAX
- T
A
)/
JA
or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4929, see
power derating currents for more information.
Note 4: Human body model, 100pF discharged through a 1.5k
resistor.
Note 5: Machine Model, 220pF-240pF discharged through all pins.
Note 6: Typicals are measured at 25C and represent the parametric norm.
Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 9: 10
Terminated input.
Note 10: Pin 3 (NC) should be connected to GND for proper part operation.
External Components Description
(Figure 2)
Components
Functional Description
1.
R
I
Inverting input resistance which sets the closed-loop gain in conjunction with R
f
. This resistor also forms a
high-pass filter with C
i
at f
c
= 1/(2
R
i
C
i
).
2.
C
I
Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a
high-pass filter with R
i
at f
c
= 1/(2
R
i
C
i
). Refer to the section Proper Selection of External Components, for
an explanation of how to determine the value of C
i
.
3.
R
f
Feedback resistance which sets the closed-loop gain in conjunction with R
i
.
4.
C
S
Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing
section for information concerning proper placement and selection of the supply bypass capacitor.
5.
C
B
Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of Proper
Components, for information concerning proper placement and selection of C
B
LM4929
www.national.com
4
PDF 
ZIP
