ChipFind - документация

Электронный компонент: OAT2009-LV-LB

Скачать:  PDF   ZIP
OKI Electronic Components
FEDFOAT2009-01
Issue Data: Jan. 15, 2002
OAT2009-LV-CB/LB
Optical Service Channel Transceiver
1/5
APPLICATION

DWDM Optical Service Channel Transmitter operated by E1 2.048Mbps
FEATURES
Integrated NRZ to/from CMI code/Decode functions
TTL compatible interface
Operation at 1.51m/1.625um wavelength(C -band / L-Band) by Uncooled DFB-LD
High output power > 0dBm and High sensitivity < -44dBm for Long haul transmission
Integrated CDR function
+3.3V single power supply
and Low power consumption 0.6W
SPECIFICATION
Parameter
Unit
OAT2009-LV-CB
OAT2009-LV-LB
Type
C-band
L-band
Bit rate
Mbps
2.048
Line code
-
CMI
Operating wavelength
nm
1510
7
1625
7
Mean launched power range
dBm
-3 to +3
Minimum extinction ratio
dB
13
Received optical power [BER = 10
-8
]
dBm
-44 to -8
Power consumption
W
0.6 (Typ.)
Laser diode
1.510 m DFB-LD
1.625 m DFB-LD
Fiber type
Single mode fiber
Power supply voltage
V
+3.3
5
%
Operating temperature
C
0 to 60
Dimension
mm
42.9 44.5 13.5

FEDFOAT2009-01
OKI Semiconductor
OAT2009-LV-CB/LB
2/5
BLOCK DIAGRAM
LD Driver
APC
Circuit
CMI Coder
CLK IN
2.048MHz
DATA IN
NRZ
CRV IN
TF
LD
Monitor
PD
LD Module
OUT
Transmitter
Clock
Detector
Doubler
DATA OUT
NRZ
CDR
Tank
CMI
Decorder
CLK OUT
2.048MHz
CRV OUT
LOS
PIN-Amp Module
PIN
-PD
IN
Receiver
FEDFOAT2009-01
OKI Semiconductor
OAT2009-LV-CB/LB
3/5
PACKAGE OUTLINE
5.4
0.3
Optical Connector
The terminal for attachment (4 places)
Quality of the material:Iron(Nickel plating)
Case back
Quality of the material:
Iron(Nickel plating)
An electric terminal
Quality of the material: Brass(Gilding)
(Unit :mm)
in the case of SC
connector
L
13.5MAX
41.9
0.5
(5.08
0.3)
(13.38)
(3.12)
6x2.54=15.24
2x2.54=5.08
(0.4)
(3)
( 0.635)
(10)
(04)
(03)
(01)
(5.2)
(0.8)
3.5
(25.4
0.3)
(0.8)
(10.2)
(0.8)
44.5
0.5
42.9
0.5
OAT2009S-LV-CB-05
(26.8)
(10)
(12.5)
17.8
12.6
4.2
554
+19
0
580
+19
0
(
0.9)
(
0.9)
5.92
FEDFOAT2009-01
OKI Semiconductor
OAT2009-LV-CB/LB
4/5
PIN DESCRIPTIONS
No.
Symbol
Functionality
01
GND
Ground
02
Vcc
Power supply (Vcc = +3.3 V)
03
LOS
Los of incoming signal <LVTTL>
A logic high on LOS indicates the absence
of a signal
04
CLK OUT
Negative clock output <LVTTL>
05
DATA OUT
Positive NZR data output <LVTTL>
06
CRV OUT
Code Rule Violation output <LVTTL>
07
TF
Transmit fail alarm output <LVTTL>
08
CLK IN
Positive clock input <LVTTL>
09
DATA IN
Positive NRZ data input <LVTTL>
10
CVR IN
Code Rule Violation signal input <LVTTL>
FEDFOAT2009-01
OKI Semiconductor
OAT2009-LV-CB/LB
5/5
NOTICE
1. The information contained herein can change without notice owing to product and/or technical improvements.
Before using the product, please make sure that the information being referred to is up -to-date.
2. The outline of action and examples for application circuits described herein have been chosen as an
explanation for the standard action and performance of the product. When planning to use the product, please
ensure that the external conditions are reflected in the actual circuit, assembly, and program designs.
3. When designing your product, please use our product below the specified maximum ratings and within the
specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating
temperature.
4. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation
resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or
unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified
maximum ratings or operation outside the specified operating range.
5. Neither indemnity against nor license of a third party's industrial and intellectual property right, etc. is
granted by us in connection with the use of the product and/or the information and drawings contained herein.
No responsibility is assumed by us for any infringement of a third party's right which may result from the use
thereof.
6. The products listed in this document are intended for use in general electronics equipment for commercial
applications (e.g., office automation, communication equipment, measurement equipment, consumer
electronics, etc.). These products are not authorized for use in any system or application that requires special
or enhanced quality and reliability characteristics nor in any system or application where the failure of such
system or application may result in the loss or damage of property, or death or injury to humans.
Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace
equipment, nuclear power control, medical equipment, and life-support systems.
7. Certain products in this document may need government approval before they can be exported to particular
countries. The purchaser assumes the responsibility of determining the legality of export of these products
and will take appropriate and necessary steps at their own expense for these.
8. No part of the contents contained herein may be reprinted or reproduced without our prior permission.
9.
Qualification and Reliability
To help ensure high product reliability and customer satisfaction, OKI is committed to an intensive quality
program that starts in the design phase and proceeds through the manufacturing process.
Optical transceiver modules are qualified to OKI internal standards using MIL-STD-883 test methods and
procedures and using sample techniques consistent with Telcordia requirements.
This qualification program fully meets the intent of Telcordia reliability practices GR-468-CORE.
10. Laser Safety
All version of transceiver are Class 1 Laser products FDA complies with 21 CFR 1040.10 and 1040.11
requirements.
Also, all versions are Class 1 Laser products pre IEC 825-1
.
Copyright 2002 Oki Electric Industry Co., Ltd.