ChipFind - документация

Электронный компонент: D3M-01K3-3

Скачать:  PDF   ZIP
1046
Subminiature Snap Action Switch
D3M
Subminiature Snap Action Switch
D3M
Saves Wiring Effort, Production Steps, and
Time
Easy wiring ensured through the Quick-Connect Terminals
External actuator mounts in either of two directions
Horizontal layout of terminals saves mounting space
Same internal mechanism as the OMRON SS Subminiature
Snap Action Switch
RoHS Compliant
Ordering Information
I
Connectors
Refer to
Wiring
under the Precautions section of this data sheet.
Actuator
Actuator mounting position
Contact type
Model
Pin plunger
--
SPST-NC
D3M-01
SPST-NO
D3M-01-3
Hinge lever
High ratio operating position
SPST-NC
D3M-01K1
SPST-NO
D3M-01K1-3
Standard operating position
SPST-NC
D3M-01L1
SPST-NO
D3M-01L1-3
Hinge roller lever
High ratio operating position
SPST-NC
D3M-01K2
SPST-NO
D3M-01K2-3
Standard operating position
SPST-NC
D3M-01L2
SPST-NO
D3M-01L2-3
Simulated roller lever
High ratio operating position
SPST-NC
D3M-01K3
SPST-NO
D3M-01K3-3
Standard operating position
SPST-NC
D3M-01L3
SPST-NO
D3M-01L3-3
Subminiature Snap Action Switch
D3M
1047
Specifications
I
Characteristics
Note: 1.
The permissible operating speed applies to pin plunger models.
2.
If a lever actuator model is used, the above vibration resistance conditions will apply when the actuator is in the maximum over-travel
position.
I
Operating Characteristics
Note: 1.
A tolerance of 0.4 mm applies to all of the above dimensions unless otherwise specified.
2.
The operating characteristics apply when each actuator is moved in the direction indicated by the arrow and "A."
I
Contact Form
SPST-NC
SPST-NO
Permissible operating speed (see note 1)
0.1 mm/s to 1 m/s
Permissible operating
frequency
Mechanical
400 operations/min max.
Electrical
60 operations/min max.
Insulation resistance
100 M
min. at 500 VDC
Contact resistance (initial value)
100 m
max. including connector and 50-mm AWG28 lead wire resistance
Dielectric strength
Between terminals of the
same polarity
1,000 VAC at 50/60 Hz for 1 min
Between charged metal part
and ground
1,500 VAC at 50/60 Hz for 1 min
Between non-charged metal
part and each terminal
1,500 VAC at 50/60 Hz for 1 min
Vibration resistance
Malfunction (See Note 2.)
10 to 55 Hz, 1.5-mm double amplitude for 1 ms max. with contacts closed or open.
Shock resistance
Destruction
1,000 m/s
2
(approx. 100G)
Malfunction (See Note 2.)
300 m/s
2
(approx. 30G) for 1 ms max. with contacts closed or open.
Life expectancy
Mechanical
500,000 operations (at full-stroke operating speed of 10 mm/s at a frequency
of 60 operations/min)
Electrical
200,000 operations (at full-stroke operating speed of 10 mm/s at a frequency of
30 operations/min)
Enclosure rating
IP00
Degree of protection against electric shock
Class I
Proof tracking index (PTI)
175
Ambient temperature
Operating
-25C to 85C (with no icing)
Ambient humidity
Operating
85% max.
Weight
Approx. 2 g (pin plunger model)
Characteristics Part
number
D3M-01
D3M-01-3
D3M-01K1
D3M-01K1-3
D3M-01L1
D3M-01L1-3
D3M-01K2
D3M-01K2-3
D3M-01L2
D3M-01L2-3
D3M-01K3
D3M-01K3-3
D3M-01L3
D3M-01L3-3
Max. operating force (OF)
153 gf
51 gf
102 gf
51 gf
102 gf
51 gf
102 gf
Min. reset force (RF)
25 gf
6 gf
10 gf
6 gf
10 gf
6 gf
10 gf
Min. pretravel (PT)
0.6 mm
--
--
--
--
--
--
Min. overtravel (OT)
0.4 mm
1.2 mm
0.7 mm
1.2 mm
0.7 mm
1.2 mm
0.7 mm
Max. movement
differential (MD)
0.1 mm
0.8 mm
0.6 mm
0.8 mm
0.6 mm
0.8 mm
0.6 mm
Max. free position (FP)
--
14.0 mm
11.5 mm
19.7 mm
17.2 mm
16.2 mm
13.6 mm
Operating position (OP)
8.40.3 mm
10.00.8 mm
9.20.6 mm
15.70.8 mm
14.90.6 mm
12.20.8 mm
11.30.6 mm
1048
Subminiature Snap Action Switch
D3M
I
Approved Standards
EN61058-1
UL1054
CSA C22.2 No. 55
I
Ratings
Use the D3M in the following permissible operating range.
Minimum Applicable Load (Level N)
Refer to
Minimum Load
under the Precautions section of this data sheet.
Dimensions
Unit: mm (inch)
I
Mounting Dimensions for All Models
Use M2.3 screws, flat washers, and spring washers to mount the
D3M securely. Make sure that the tightening torque applied to each
screw is within a range from 2.3 to 2.7 kgf cm.
Rated voltage
Resistive load
30 VDC
0.1 A
Voltage
Resistive load
5 VDC
1 mA
Subminiature Snap Action Switch
D3M
1049
I
Pin Plunger
D3M-01
D3M-01-3
I
Hinge Lever
D3M-01K1
D3M-01K1-3
1050
Subminiature Snap Action Switch
D3M
I
Hinge Lever
D3M-01L1
D3M-01L1-3
I
Hinge Roller Lever
D3M-01K2
D3M-01K2-3