Power PCB Relay

G6D-ASI

603

Coil Data

Note: 1.

The rated current and coil resistance are measured at a coil temperature of 23°C (73°F) with a tolerance of ±10%.

Operating characteristics are measured at a coil temperature of 23°C (73°F).

The pick-up voltage is 75% or less of rated voltage if the relay is mounted upside down.

Characteristics

Note:

Data shown are of initial value.

Characteristic Data

Rated

voltage

(VDC)

Rated

current

(mA)

Coil

resistance

(

)

Pick-up

voltage

Dropout

voltage

Maximum

voltage

Power

consumption

(mW)

% of rated voltage

125

70% max.

10% min.

160% at 23°C

Approx. 200

16.7

720

8.3

2,880

Contact resistance

100 m

max.

Operate time

10 ms max.

Release time

5 ms max.

Operating
frequency

Mechanical

18,000 operations/hour

Electrical

1,800 operations/hour (under rated load)

Insulation resistance

1,000 M

min. (at 500 VDC)

Dielectric strength

3,000 VAC, 50/60 Hz for 1 minute between coil and contacts

750 VAC, 50/60 Hz for 1 minute between contacts of the same polarity

Surge withstand voltage

6,000 V, 1.20 x 50 µs between coil and contacts

Vibration

Mechanical durability

10 to 55 Hz, 1.50 mm (0.06 in) double amplitude

Malfunction durability

10 to 55 Hz, 1.50 mm (0.06 in) double amplitude

Shock

Mechanical durability

1,000 m/s

(approx. 100 G)

Malfunction durability

100 m/s

(approx. 10 G)

Ambient temperature

Operating

-25° to 70°C (-13° to 158°F)

Humidity

5% to 85% RH

Life expectancy

Mechanical

20 million operations min. (at operating frequency of 18,000 operations/hour)

Electrical

70,000 operations min. at rated loads (300,000 operations min for 2A at 250 VAC, 30 VDC,
resistive load)

Weight

Approx. 3 g (0.10 oz)

1 2 3 4 5 6 7 8 9

500

300

100

250-VAC/30-VDC resistive load

250-VAC/30 VDC inductive load
(cos =0.4/ L/R=7 ms)

Maximum switching capacity

Life expectancy

Ambient temperature vs.
maximum voltage

Rated operating voltage (V)

d o

pera

t
i
ng

cur

r
en

t (A

)

Ambient temperature (

°C)

i
mum v

l
t
ag

(
%

)

Switching current (A)

ranc

e (

ope

rati

Power PCB Relay

G6D-ASI

605

Approvals

The rated values approved by each of the safety standards may be different from the performance characteristics individually defined in this catalog.

UL Approval

(File No. E41515) UL508

CSA Approval

(File No. LR31928) C22.2 No. 14

EN/TÜV Approval

(Registration No. R50029064/EN61810-1)

Note: 1.

The rated values approved by each of the safety standards (e.g., UL, CSA, TUV) may be different from the performance characteristics
individually defined in this catalog.

In the interest of product improvement, specifications are subject to change.

Precautions

Spacing Between Relays

More than two relays can be closely mounted right side up as shown
in the illustration below.

More than two relays can be closely mounted upside down as shown
in the illustration below.

Note:

The space between each relay required for heat radiation may
vary with operating conditions.

Socket Mounting

When mounting the relay, insert it into the socket as vertically as pos-
sible so that the relay terminals contact securely with the contact pins
on the socket.

The P6D-04P socket is flux-resistant. Do not wash the socket with
water.

Remove the relay from the socket before soldering the socket to a
PC board.

Mounting height

Model

Number of poles

Coil ratings

Contact ratings

Number of test

operations

G6D-1A-ASI

5 to 24 VDC

5 A, 250 VAC (General Use)

6,000

5 A, 30 VDC

Model

Number of poles

Coil ratings

Contact ratings

Number of test

operations

G6D-1A-ASI

5 to 24 VDC

5 A, 250 VAC (General Use)

6,000

5 A, 30 VDC (Resistive)

Model

Number of poles

Coil ratings

Contact ratings

Number of test

operations

G6D-1A-ASI

5, 12, 24 VDC

5 A, 250 VAC (cos

=1.0) 70,000

5 A, 30 VDC (0 ms)

Terms and Conditions of Sale

Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotations, acknowledgments, invoices, purchase orders and other
documents, whether electronic or in writing, relating to the sale of products or
services (collectively, the "Products") by Omron Electronic Components LLC
("Seller"). Seller hereby objects to any terms or conditions proposed in
Buyer's purchase order or other documents which are inconsistent with, or in
addition to, these Terms.

2. Prices;

Payment. All prices stated are current, subject to change without

notice by Seller. Buyer agrees to pay the price in effect at time of shipment.
Payments for Products received are due net 30 days unless otherwise stated
in the invoice.

3. Discounts. Cash discounts, if any, will apply only on the net amount of

invoices sent to Buyer after deducting transportation charges, taxes and
duties, and will be allowed only if (i) the invoice is paid according to Seller's
payment terms and (ii) Buyer has no past due amounts owing to Seller.

4. Currencies. If the prices quoted herein are in a currency other than U.S. dol-

lars, Buyer shall make remittance to Seller at the then current exchange rate
most favorable to Seller and which is available on the due date; provided that if
remittance is not made when due, Buyer will convert the amount to U.S. dol-
lars at the then current exchange rate most favorable to Seller available during
the period between the due date and the date remittance is actually made.

5. Governmental

Approvals. Buyer shall be responsible for, and shall bear all

costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.

6. Taxes. All taxes, duties and other governmental charges (other than general

real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Seller or required to be collected directly or
indirectly by Seller for the manufacture, production, sale, delivery, importation,
consumption or use of the Products sold hereunder (including customs duties
and sales, excise, use, turnover and license taxes) shall be charged to and
remitted by Buyer to Seller.

7. Financial. If the financial position of Buyer at any time becomes unsatisfactory

to Seller, Seller reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Seller may (without liability
and in addition to other remedies) cancel any unshipped portion of Products
sold hereunder and stop any Products in transit until Buyer pays all amounts,
including amounts payable hereunder, whether or not then due, which are
owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.

8. Cancellation; Etc. Orders are not subject to rescheduling or cancellation

unless Buyer indemnifies Seller fully against all costs or expenses arising in
connection therewith.

9. Force

Majeure. Seller shall not be liable for any delay or failure in delivery

resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.

10. Shipping; Delivery. Unless otherwise expressly agreed in writing by Seller:

1. Shipments shall be by a carrier selected by Seller;
2. Such carrier shall act as the agent of Buyer and delivery to such carrier

shall constitute delivery to Buyer;

3. All sales and shipments of Products shall be FOB shipping point (unless

otherwise stated in writing by Seller), at which point title to and all risk of
loss of the Products shall pass from Seller to Buyer, provided that Seller
shall retain a security interest in the Products until the full purchase price is
paid by Buyer;

4. Delivery and shipping dates are estimates only.
5. Seller will package Products as it deems proper for protection against

normal handling and extra charges apply to special conditions.

11. Claims. Any claim by Buyer against Seller for shortage or damage to the

Products occurring before delivery to the carrier must be presented in writing
to Seller within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Seller in the condition claimed.

12. Warranties. (a) Exclusive Warranty. Seller's exclusive warranty is that the

Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Seller (or such other period expressed
in writing by Seller). Seller disclaims all other warranties, express or implied.
(b) Limitations. SELLER MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Seller further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Seller's sole obli-
gation hereunder shall be to replace (in the form originally shipped with Buyer
responsible for labor charges for removal or replacement thereof) the non-
complying Product or, at Seller's election, to repay or credit Buyer an amount
equal to the purchase price of the Product; provided that in no event shall
Seller be responsible for warranty, repair, indemnity or any other claims or
expenses regarding the Products unless Seller's analysis confirms that the
Products were properly handled, stored, installed and maintained and not sub-
ject to contamination, abuse, misuse or inappropriate modification. Return of
any Products by Buyer must be approved in writing by Seller before shipment.
Seller shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies, or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing
are not to be construed as an amendment or addition to the above warranty.

13. Limitation on Liability; Etc. SELLER SHALL NOT BE LIABLE FOR SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CON-
NECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in
no event shall liability of Seller exceed the individual price of the Product on
which liability is asserted.

14. Indemnities. Buyer shall indemnify and hold harmless Seller, its affiliates and

its employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Seller is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Seller and defend or settle
any action brought against Seller to the extent that it is based on a claim that
any Product made to Buyer specifications infringed intellectual property rights
of another party.

15. Property; Confidentiality. The intellectual property embodied in the Products is

the exclusive property of Seller and its affiliates and Buyer shall not attempt to
duplicate it in any way without the written permission of Seller. Notwithstand-
ing any charges to Buyer for engineering or tooling, all engineering and tooling
shall remain the exclusive property of Seller. All information and materials sup-
plied by Seller to Buyer relating to the Products are confidential and propri-
etary, and Buyer shall limit distribution thereof to its trusted employees and
strictly prevent disclosure to any third party.

16. Miscellaneous. (a) Waiver. No failure or delay by Seller in exercising any right

and no course of dealing between Buyer and Seller shall operate as a waiver
of rights by Seller. (b) Assignment. Buyer may not assign its rights hereunder
without Seller's written consent. (c) Law. These Terms are governed by Illi-
nois law (without regard to conflict of law principles). Federal and state courts
in Illinois shall have exclusive jurisdiction for any dispute hereunder.
(d) Amendment. These Terms constitute the entire agreement between Buyer
and Seller relating to the Products, and no provision may be changed or
waived unless in writing signed by the parties. (e) Severability. If any provision
hereof is rendered ineffective or invalid, such provision shall not invalidate any
other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice.. (g) Definitions. As used
herein, "including" means "including without limitation".

Certain Precautions on Specifications and Use

1. Suitability for Use. Seller shall not be responsible for conformity with any stan-

dards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will pro-
vide applicable third party certification documents identifying ratings and limita-
tions of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in combi-
nation with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the partic-
ular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a non-
exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical

interference, or conditions or uses not described in this document.

(ii) Energy control systems, combustion systems, railroad systems, aviation

systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to
separate industry or government regulations.

(iii)Use in consumer products or any use in significant quantities.
(iv)Systems, machines and equipment that could present a risk to life or

property. Please know and observe all prohibitions of use applicable to this
product.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

2. Programmable Products. Seller shall not be responsible for the user's

programming of a programmable product, or any consequence thereof.

3. Performance Data. Performance data given in this publication is provided as a

guide for the user in determining suitability and does not constitute a warranty.
It may represent the result of Seller's test conditions, and the users must corre-
late it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.

4. Change in Specifications. Product specifications and accessories may be

changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for your
application. Please consult with your Seller representative at any time to con-
firm actual specifications of purchased Product.

5. Errors and Omissions. The information in this publication has been carefully

checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.

6. RoHS Compliance. Where indicated, our products currently comply, to the best

of our knowledge as of the date of this publication, with the requirements of the
European Union's Directive on the Restriction of certain Hazardous Sub-
stances ("RoHS"), although the requirements of RoHS do not take effect until
July 2006. These requirements may be subject to change. Please consult our
website for current information.

OMRON ON-LINE

Global - http://www.omron.com
USA - http://www.components.omron.com
Canada - http://www.omron.ca

Cat. No. JB301-E3-01

Printed in USA

OMRON CANADA, INC.

885 Milner Avenue
Toronto, Ontario M1B 5V8

416-286-6465

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B
Schaumburg, IL 60173

847-882-2288

3/05 Specifications subject to change without notice

Complete "Terms and Conditions of Sale" for product purchase and use are on Omron's website
at www.components.omron.com under the "About Us" tab, in the Legal Matters section.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: G6D-1ADC12

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: G6D-1ADC12