ChipFind - документация

Электронный компонент: T-51513D104U-FW-A-AB

Скачать:  PDF   ZIP
T-51513-D104U-FW-A-AB (AB) No. 2002-0186
OPTREX CORPORATION
Page 1/37
LCD Module Technical Specification
T-51513-D104U-FW-A-AB
CONTENTS
No.
Item
Page
1
OVERVIEW
2
2
ABSOLUTE MAXIMUM RATINGS
3
3
ELECTRICAL CHARACTERISTICS
3
5
4
INTERFACE PIN CONNECTION
6
5
INTERFACE TIMING
7
9
6
BLOCK DIAGRAM
10
7
MECHANICAL SPECIFICATION
11
13
8
OPTICAL CHARACTERISTICS
14,15
9
RELIABILITY TEST CONDITION
16
10
INSPECTION STANDARDS
17
11
HANDLING PRECAUTIONS FOR TFT-LCD MODULE
18
20
12
REVISION STATUS
21,22
13
REVISION STATUS (INTERNAL USE ONLY)
23
14
PACKAGING SPECIFICATION
23
27
15
PRODUCTS NUMBER LABELING FORMS
28
30
16
LAMP UNIT FOR 10.4 VGA
31
37
Checked by (Design Engineering Div.)
Checked by (Quality Assurance Div.)
Approved by (Production Div.)
Prepared by (Production Div.)
Type No.
Jul 1, 2002
O P T R E X
First Edition
Final Revision
******
T-51513-D104U-FW-A-AB (AB) No. 2002-0186
OPTREX CORPORATION
Page 2/37
1. OVERVIEW
AA104VB05 is 10.4" color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed
of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit digital data 640
480, 260K-color images are displayed on the 10.4" diagonal screen.
Input power voltage is single 3.3 / 5.0V for LCD driving. Both 3.3V-CMOS and 5.0V-CMOS level
voltage are acceptable for logic input voltage.
Inverter for backlight is not included in this module. General specifications are summarized in the
following table:
ITEM
SPECIFICATION
Display Area (mm)
211.2 (H)
158.4 (V)
(10.39-inch diagonal)
Number of Dots
640
3 (H)
480 (V)
Pixel Pitch (mm)
0.33 (H)
0.33 (V)
Color Pixel Arrangement
RGB vertical stripe
Display Mode
normally white
Number of Color
260 K
Wide Viewing Angle Technology
Optical compensation film
Optimum Viewing Angle(Contrast ratio)
12 o'clock
Brightness (cd/m
2
)
380
Module Size (mm)
243.0 (W)
181.6 (H)
12.2 (D)
Module Mass (g)
530
Backlight Unit
CCFL, 2-tubes, replaceable
Surface Treatment
Anti-glare and hard-coating 3H
Characteristic value without any note is typical value.
The LCD product described in this specification is designed and manufactured for the standard use
in OA equipment and consumer products, such as computers, communication equipment, industrial
robots, AV equipment and so on.
Do not use the LCD product for the equipment that require the extreme high level of reliability,
such as aerospace applications, submarine cables, nuclear power control systems and medical or
other equipment for life support.
ADI assumes no responsibility for any damage resulting from the use of the LCD product in disre-
gard of the conditions and handling precautions in this specification.
If customers intend to use the LCD product for the above items or other no standard items,
please contact our sales persons in advance.
T-51513-D104U-FW-A-AB (AB) No. 2002-0186
OPTREX CORPORATION
Page 3/37
2. ABSOLUTE MAXIMUM RATINGS
ITEM
SYMBOL
MIN.
MAX.
UNIT
Power Supply Voltage for LCD
VCC
-0.3
6.5
V
Logic Input Voltage
VI
0
6.5
V
Lamp Voltage
VL
0
2000
Vrms
Lamp Current
IL
0
10.0
mArms
Lamp Frequency
FL
--
80
kHz
Operation Temperature *1)
T
op
0
50
C
Storage Temperature *1)
T
stg
-20
60
C
[Note]
*1) Top,Tstg
40
C : 90%RH max. without condensation
Top,Tstg > 40
C : Absolute humidity shall be less than the value of 90%RH at 40
C without
condensation.
3. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD
Ambient Temperature : Ta = 25C
ITEM
SYMBOL
MIN.
TYP.
MAX.
UNIT
Remarks
3.3 V powered
VCC
3.0
3.3
3.6
V
A), D)
Power Supply
Voltage for LCD
5.0 V powered
VCC
4.75
5.0
5.25
V
A), D)
3.3 V powered
ICC
-
220
380
mA
VCC=3.3 V
B)
Power Supply
Current for LCD 5.0 V powered
ICC
-
150
280
mA
VCC=5.0 V
B)
Permissive Input Ripple Voltage
VRP
-
-
100
mVp-p VCC=+3.3 V/5.0 V
High
VIH
2.0
-
5.25
V
Logic Input
Voltage
Low
VIL
0
-
0.8
V
(2) Backlight Ta=25C
ITEM
SYMBOL MIN.
TYP.
MAX.
UNIT
Remarks
Lamp Voltage
VL
--
580
--
Vrms
IL=6.0mArms
Lamp Current
IL
3.0
6.0
7.0
mArms
*1)
Lamp Frequency
FL
40
--
80
kHz
*2)
Starting Lamp Voltage
Ta=25C
810
--
--
Vrms
Ta=0C
VS
1000
--
--
Vrms
IL=3.0mArms
50000
50000
--
h
*3),*4)
Lamp Life Time
IL=6.0mArms
LT
40000
50000
--
h
IL=7.0mArms
30000
40000
--
h
T-51513-D104U-FW-A-AB (AB) No. 2002-0186
OPTREX CORPORATION
Page 4/37
*1) Lamp Current measurement method (The current meter is inserted in low voltage line.)
CTL
CTH
CTL
CTH
LCD
Module
A
Inverter
Power
Supply
A
*2) Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and
this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and keep
inverter as far from module as possible or use electronic shielding between inverter and module to
avoid the interference.
*3) Lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or
when the starting lamp voltage does not meet the value specified in this table.
*4) The life time of the backlight depends on the ambient temperature. The life time will decrease under
low/high temperature.
[Note]
A) Power and signals sequence:
t1
10
ms
400 ms
t5
0 < t2
50 ms
200 ms
t6
0 < t3
50 ms
0
t7
0 < t4
50 ms
t1
t2
t3
data
0.9VCC
0.9VCC
0.1VCC
VCC
t4
t5
t6
t7
Backlight
data: RGB DATA, DCLK, HD, VD, DENA
0.1VCC
0.1VCC
T-51513-D104U-FW-A-AB (AB) No. 2002-0186
OPTREX CORPORATION
Page 5/37
VCC-dip conditions:
(a) 3.3 V powered
1) When 2.4 V
VCC < 3.0 V, td
10 ms
2) When VCC < 2.4 V
VCC-dip conditions should also follow the power and signals sequence.
td
2.4 V
3.0 V
VCC
(b) 5.0 V powered
1) When 3.6 V
VCC < 4.5 V, td
10 ms
2) When VCC < 3.6 V
VCC-dip conditions should also follow the power and signals sequence.
td
3.6 V
4.5 V
VCC
B) Typical current condition:
64- gray- bar-pattern
480 line mode
VCC = + 3.3 / 5.0 V, f
H
=31.6kHz, f
V
=60Hz, f
CLK
= 25MHz