AN15526A
2
SDB00089AEB
Contents
Overview ............................................................................................................................ 3
Features ............................................................................................................................. 3
Applications ........................................................................................................................ 3
Package ............................................................................................................................ 3
Application Circuit ................................................................................................................ 4
Block Diagram ...................................................................................................................... 6
Pin Descriptions ..................................................................................................................... 6
Absolute Maximum Ratings .................................................................................................... 7
Operating Supply Voltage Range ............................................................................................. 7
AN15526A
3
SDB00089AEB
AN15526A
Silicon Monolithic Bipolar IC
Overview
AN15526A are ICs for CRT vertical deflection output. AN15526A can directly drive a deflection coil with saw wave output from
a signal processing IC.
With its maximum output current of 2.4 A[p-p], AN15526A are suitable for the use of driving of 32 inch to 36 inch monitors.
Features
Vertical output circuit
Built-in pump up circuit
Built-in thermal protection circuit
Absolute maximum rating 80 V
Maximum output current 2.4 A[p-p]
Applications
CRT vertical output
TV sets and displays
Package
T0220 - 7pin plastic package with Fin
AN15526A
7
SDB00089AEB
Absolute Maximum Ratings
Operating Supply Voltage Range
Note ) 1 : Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25
C
2 : The power dissipation shall be at Ta = 70
C in free air, without heat sink. ( refer to sheet no. 13,17 )
to 2.4 A[p-p]
I
5p-p
Deflection output current
12 V to 35 V
V
CC2
Operating supply voltage range
A[0-p]
1.5
1.5
I
5
, I
3
Circuit current
11
V
V
2-4
0
V
7-4
, V
1-4
Circuit voltage
10
V
80
0
V
5-4
, V
6-4
Circuit voltage
9
*2
W
1.5
P
D
Power dissipation
8
mA
360
I
CC2
Supply current
7
V
40
V
CC2
Supply voltage
6
m/S
2
4 900
S
opr
Operating shock
5
m/S
2
9 810
G
opr
Operating constant gravity
4
Pa
1.013
10
5
0.61
10
5
P
opr
Operating ambient atmospheric pressure
3
*1
C
20 to +70
T
opr
Operating ambient temperature
2
*1
C
55 to +150
T
stg
Storage temperature
1
Note
Unit
Rating
Symbol
Parameter
No.
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of
the products or technical information described in this material and controlled under the "Foreign Exchange
and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and
applied circuits examples of the products. It neither warrants non-infringement of intellectual property right
or any other rights owned by our company or a third party, nor grants any license.
(3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical
information as described in this material.
(4) The products described in this material are intended to be used for standard applications or general elec-
tronic equipment (such as office equipment, communications equipment, measuring instruments and house-
hold appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus-
tion equipment, life support systems and safety devices) in which exceptional quality and reliability are
required, or if the failure or malfunction of the products may directly jeopardize life or harm the human
body.
Any applications other than the standard applications intended.
(5) The products and product specifications described in this material are subject to change without notice for
modification and/or improvement. At the final stage of your design, purchasing, or use of the products,
therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifica-
tions satisfy your requirements.
(6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rat-
ing, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not
be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of
break down and failure mode, possible to occur to semiconductor products. Measures on the systems such
as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent
physical injury, fire, social damages, for example, by using the products.
(7) When using products for which damp-proof packing is required, observe the conditions (including shelf life
and amount of time let standing of unsealed items) agreed upon when specification sheets are individually
exchanged.
(8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written
permission of Matsushita Electric Industrial Co., Ltd.
2003 SEP
PDF 
ZIP
