s Overview
The DN6848/SE/TE/S is a combination of a Hall element,
amplifier, Schmitt circuit, and stabilized power supply/temper-
ature compensator integrated on an identical chip by using the
IC technology. It amplifies Hall element output at the amplifi-
er, converts into a digital signal through the Schmitt circuit,
and drives the TTL or MOS IC directly.
s Features
High sensitivity and low drift
Stable temperature characteristics due to the additional tem-
perature compensator
Wide operating supply voltage range (V
CC
=4.5 to 16V)
Operating in one way magnetic field
TTL and MOS ICs directly drivable by output
Output open collector
s Applications
Speed sensors
Position sensors
Rotation sensors
Keyboard switches
Microswitches
Note) This IC is not suitable for car electrical equipments.
DN6848/SE/TE/S
Hall IC (Operating Temperature Range
Topr =
40
to +100C,
Operating in One
Way Magnetic Field)
Unit : mm
DN6848
SSIP003-P-0000A (E-3S)
1 : V
CC
2 : GND
3 : Output
0.5
0.1
5
1 2 3
2
5
5
2
1.27
4.0
0.3
0.7
4.5
0.3
0.43
+ 0.1
0.05
2.0
0.3
0.8
0.1
1.0
10.5
0.5
Unit : mm
DN6848SE
4.52
0.3
0.55
0.15
0.4
0.1
1.54
0.1
1.27
R0.25
2 to 5
2
1 2 3
(0.4)
12.5
06.5
(0.72)
4.52
0.3
(1.0)
(1.0)
2
45
SSIP003-P-0000 (SE-3S)
1 : V
CC
2 : GND
3 : Output
Unit : mm
DN6848TE
4.0
0.3
0.6
0.15
0.5
0.1
1.2
0.1
(0.2)
1.27
1 2 3
3.3
0.3
(0.6)
(0.7)
(1.0)
(1.0)
SSIP003-P-0000B (TE-3S)
1 : V
CC
2 : GND
3 : Output
10.0
0.6
1.6
3.0
0.3
0.6
0.2
ESOP004-P-0200 (SOH-4D)
1
2
4
3
Unit : mm
5.4
0.4
3.0
0.3
1.5
0.3
0.4
0.2
0 to 0.1
0.15
0.95
0.2
0.3 to 0.5
1 : V
CC
2 : NC or GND
3 : Output
4 : GND
DN6848S
Hall Element
DN6848/SE/TE
Amp.
Schmitt Trigger Output Stage
3
2
1
V
CC
Output
GND
Stabilized Power Supply
Temperature Correction Circuit
s Block Diagram
1
Hall Element
DN6848S
Amp.
Schmitt Trigger Output Stage
3
4
2
NC
or
GND
V
CC
Output
GND
Stabilized Power Supply
Temperature Correction Circuit
V
CC
I
CC
I
O
P
D
T
opr
T
stg
Supply voltage
Supply current
Circuit current
Power dissipation
Operating ambient temperature
Storage temperature
V
mA
mA
mW
C
C
18
8
20
150
40 to +100
55 to +125
Parameter
Symbol
Rating
Unit
s Absolute Maximum Ratings (Ta=25C)
Operating flux density
0.5
B
1 (L to H)
mT
9
V
CC
=12V
B
2 (H to L)
22
mT
11
V
CC
=12V
Hysteresis width
1
BW
mT
2
V
CC
=12V
Low output voltage
V
OL
0.4
V
V
CC
=4.5 to 16V
V
O
=16V, B=0mT
High output current
I
OH
10
A
Supply current
mA
V
CC
=16V
I
CC
5.5
mA
V
CC
=4.5V
6
21
0.4
1.5
V
V
CC
=4.5V, I
O
=12mA,
B=22mT
V
CC
=16V, I
O
=12mA,
B=22mT
Parameter
Symbol
Condition
min
typ
max
Unit
s Electrical Characteristics (Ta=25C)
1.5
1.5
1.0
1.3
1.0 1.75
1.0
1.0
1.0
1.25
1.0 1.63
1.0
1.15
1.0 1.5
Distance from package
surface to sensor (mm)
DN6848
0.7
DN6848SE
0.42
DN6848TE
0.4
DN6848S
0.65
Unit : mm
The center of the Hall
element is in the hatched
area in the right figure.
s Hall Element Position
Marking surface
Applied flux direction
Flux density (B)
Output voltage (V
O
)
B
1
B
2
s Flux-Voltage Conversion Characteristics
s Precaution on Use
1. Change of the operation magnetic flux density does not depend on the supply voltage, because the stabilization
power supply is built-in. (only for the range ; V
CC
= 4.5 to 16V)
2. Change from "H" to "L" level increases the supply current by approx. 1mA.
V
CC
= 4.5V
Ambient temperature (C)
Supply current (mA)
Supply voltage Ambient temperature
8
7
6
5
4
3
2
1
0
50 25
0
25
50
75 100
V
CC
= 16V
Ambient temperature (C)
Operating flux density (mT)
Operating flux density Ambient temperature
25.0
22.5
20.0
17.5
15.0
12.5
10.0
7.5
5.0
2.5
50 25
0
25
50
V
CC
= 4.5 to 16V
B
H
L
75 100
Sam
ple 1
Sample 2
Sample 3
Sample 4
Ambient temperature (C)
Output "L" level voltage (mV)
Output low level voltage Ambient temperature
100
90
80
70
60
50
40
30
20
10
0
50 25
0
25
50
V
CC
=12V
I
O
=12mA
75 100 125
Supply voltage (V)
Operating flux density (mT)
Operating flux density Supply voltage
20.0
17.5
15.0
12.5
10.0
7.5
5.0
2.5
0
0
2
4
6
8
10 12 14 16 18 20
Ta =25C
s Characteristics Curve
PDF 
ZIP