PAGE . 1
DAT
E : AUG.29.2002
FEATURES
Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
Ideal for printed circuit board
Reliable low cost construction utilizing molded plastic technique
Surge overload rating: 200 Amperes peak
High temperature soldering guaranteed:
260C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
GBJ10A~GBJ10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
DATA SHEET
GBJ
Unit: inch ( mm )
0.603
(15.3
)
C
0.118
(3.0)
0.709
(18.0
)
0.304(7.7)
0.304(7.7)
0.304(7.7)
0.382
(9.7
)
0.150(3.8)
0.115(2.9)
0.032(0.8)
0.142(3.6)
0.996(25.3)
0.972(24.7)
0.578
(14.7
)
0.669
(17.0
)
0.070(1.8)
0.288(7.3)
0.288(7.3)
0.288(7.3)
0.024(0.6)
0.098(2.5)
0.366
(9.3
)
0.122(3.1)
0.133(3.4)
0.173(4.4)
0.189(4.8)
0.044(1.1)
0.035(0.9)
0.087(2.2)
0.129(3.3)
0.146(3.7)
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100C
Rectified Output Current T
A
= 45C
I
2
t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
Maximum Reverse Leakage at rated T
A
=25
CDc Blocking Voltage per element T
C
=100C
Typical Thermal Resistance per leg(Note 2) R
JA
Typical Thermal Resistance per leg(Note 3) R
JC
Operating and Storage Temperature Range, T
J
,TSTG
V
V
V
A
A
2
sec
Apk
A
C / W
UNIT
C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate.
A
50
35
50
Vpk
10.0
8.0
166
200
1.0
5
500
18.0
3.0
-55 to +150
C / W
GBJ10A
100
70
100
GBJ10B
200
140
200
GBJ10D
400
280
400
GBJ10G
600
420
600
GBJ10J
GBJ10K
800
560
800
PAGE . 2
DATE : AUG.29.2002
5.0
INSTANTANEOUS FORWARD VOLTAGE, VOLT
Fig.2 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER ELEMENT
TEMPERATURE
Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
PERCENT OF PEAK REVERSE VOLTAGE
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
NO. OF CYCLES AT 62Hz
Fig.4 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
REVERSE VOLTAGE, VOLTS
CAP
ACIT
ANCE,
pF
TJ = 25
f = 1MHz
Visg = 50m Vp-p
FOR
W
ARD
SURGE
CURRENT
,
AMPERES
pk
(HALF
SINE-W
A
VE)
INST
ANTNEOUS
REVERSE
CURRENT
,
MICROAMPERES
GO
C
U
AMPERES
INST
ANT
ANEOUS
FOR
W
ARD
CURRENT
,
AMPERES
60Hz RESISTIVE OR
INDUCTIVE LOAD
MOUNTED ON 0.5X0.5 INCH
COPPER PC BOARD, TA
0.5"(12.7mm) LEAD LENGTH
HEAT-SINK
MOUNTING, TC
(4X4X0.15) INCH
COPPER PLATE
TJ = 25
Pulse Width = 30uS
1% Duty Cycle
200
160
120
80
40
0
PDF 
ZIP