PAGE . 1
Approve Sheet
Part Number: GBJ6A~GBJ6K
FEATURES
Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
Ideal for printed circuit board
Reliable low cost construction utilizing molded plastic technique
Surge overload rating: 175 Amperes peak
High temperature soldering guaranteed:
260C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
GBJ6A~GBJ6K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
DATA SHEET
GBJ
Unit: inch ( mm )
0.603
(15.3
)
C
0.118
(3.0)
0.709
(18.0
)
0.304(7.7)
0.304(7.7)
0.304(7.7)
0.382
(9.7
)
0.150(3.8)
0.115(2.9)
0.032(0.8)
0.142(3.6)
0.996(25.3)
0.972(24.7)
0.578
(14.7
)
0.669
(17.0
)
0.070(1.8)
0.288(7.3)
0.288(7.3)
0.288(7.3)
0.024(0.6)
0.098(2.5)
0.366
(9.3
)
0.122(3.1)
0.133(3.4)
0.173(4.4)
0.189(4.8)
0.044(1.1)
0.035(0.9)
0.087(2.2)
0.129(3.3)
0.146(3.7)
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100C
Rectified Output Current
I
2
t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 6.0A
Maximum Reverse Leakage at rated T
A
=25
CDc Blocking Voltage per element T
C
=100C
Typical Thermal Resistance per leg(Note 2) R
JA
Typical Thermal Resistance per leg(Note 3) R
JC
Operating and Storage Temperature Range, T
J
,TSTG
V
V
V
A
A
2
sec
Apk
A
C / W
UNIT
C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
A
50
35
50
Vpk
6.0
127
175
1.0
5
500
8.6
3.1
-55 to +150
C / W
GBJ6A
100
70
100
GBJ6B
200
140
200
GBJ6D
400
280
400
GBJ6G
600
420
600
GBJ6J
800
560
800
GBJ6K
PAGE . 2
Approve Sheet
Part Number: GBJ6A~GBJ6K
A
V
ERA
G
E
F
ORW
ARD
CURRENT
AMPERES
MOUNTED ON PC BOARD.
TA 0.5"(12.7mm) LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD
TEMPERATURE C
O
Fig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
RATING AND CHARACTERISTIC CURVES
HEAT-SINK
MOUNTING,TC
(4* 4* 0.15) INCH
COPPER PLATE
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig. 2- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISITCS PER ELEMENT
INST
ANT
A
NEOUS
F
ORW
ARD
CURRENT
,
A
MPERES
TJ=25OC
Pulse Width=300 S
1% DULY Cycle
INST
ANT
A
NEOUS
R
EVERSE
CURRENT
,
MICRO
AMPERES
PERCENT OF PEAK REVERSE VOLTAGE
Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS
T =100 C
C
O
T =25 C
A
O
FPRW
ARD
SURGE
C
URRENT
,
A
MPERES
pk
(HALF
SINE-
W
A
V
E)
NO. OF CYCLES AT 62Hz
Fig. 4- MAXIMUM NON-REPETITEVE PEAK
FORWARD SURGE CURRENT
T =105 C
A
O
CAP
A
CIT
ANCE,
p
F
REVERSE VOLTAGE, VOLTS
Fig. 5- TYPICL JUNCTION CAPACITANCE PER ELEMENT
Tj=25 C
f=1.0MHz
Vsig=50mVp-p
O
6.0
4.0
2.0
0
0
50
100
150
100
40
20
10
4.0
2.0
1.0
0.4
0.2
0.1
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
10
1.0
0.1
0.01
0
20
40
60
80
100
120
140
150
120
90
60
30
0
1
2
6
10
20
40
60
100
400
100
50
10
1
5
10
50
100
PDF 
ZIP