PAGE . 1
DATE : AUG.29.2002
FEATURES
Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
Ideal for printed circuit board
Reliable low cost construction utilizing molded plastic technique
Surge overload rating: 200 Amperes peak
High temperature soldering guaranteed:
260C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
DATA SHEET
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100C
Rectified Output Current at
I2t Rating for fusing ( t<8.35ms)
Peak Forward Surge Current single sine-wave superimposed on
rated load(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
Maximum Reverse Leakage at rated T
A
=25
CDc Blocking Voltage per element T
C
=100C
Typical Thermal Resistance per leg(Note 2) R
JA
Typical Thermal Resistance per leg(Note 3) R
JC
Operating and Storage Temperature Range, T
J
,TSTG
V
V
V
A
A
2
sec
Apk
A
C / W
UNIT
C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
A
Vpk
GBU10A
50
35
50
10.0
127
200
1.0
5.0
500
8.6
3.1
-55+150
C / W
GBU
Unit: inch ( mm )
.880(22.3)
.860(21.8)
.160(4.1)
.140(3.5)
.190(4.83)
.080
(2.03
)
.060
(1.52
)
.140(3.56)
.022(0.56)
.210(5.33)
.050(1.27)
.040(1.02)
.720
(18.3
)
.740
(18.8
)
.130(3.30)
.018(0.46)
.290
(7.40
)
.310
(7.90
)
.085
(2.16
)
.065
(1.65
)
.075
(1.90
)R
.710
(18.0
)
.690
(17.5
)
.040(1.02)
.030(0.76)
.100(2.54)
.085(2.16)
.080(2.03)
.065(1.65)
GBU10K
800
560
800
GBU10J
600
420
600
GBU10G
400
280
400
GBU10D
200
140
200
GBU10B
100
70
100
PAGE . 2
DATE : AUG.29.2002
5.0
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig.2 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER ELEMENT
TEMPERATURE
Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
RATING AND CHARACTERISTIC CURVES
PERCENT OF PEAK REVERSE VOLTAGE
Fig.3 - TYPICAL REVERSE CHARACTERISTICS
NO. OF CYCLES AT 62Hz
Fig.4 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
REVERSE VOLTAGE, VOLTS
Fig.5 - TYPICAL JUNCTION CAPACITANCE PER ELEMENT
CAP
ACIT
ANCE,
pF
TJ = 25
f = 1MHz
Visg = 50m Vp-p
FOR
W
ARD
SURGE
CURRENT
,
AMPERES
pk
(HALF
SINE-W
A
VE)
INST
ANTNEOUS
REVERSE
CURRENT
,
MICROAMPERES
A
VERAGE
FOR
W
ARD
CURRENT
AMPERES
INST
ANT
ANEOUS
FOR
W
ARD
CURRENT
,
AMPERES
60Hz RESISTIVE OR
INDUCTIVE LOAD
MOUNTED ON 0.5X0.5 INCH
COPPER PC BOARD, TA
0.5"(12.7mm) LEAD LENGTH
HEAT-SINK
MOUNTING, TC
(4X4X0.15) INCH
COPPER PLATE
TJ = 25
Pulse Width = 30uS
1% Duty Cycle
200
160
120
80
40
0
PDF 
ZIP