1
PS8714 12/15/03
Features
Low On-Resistance: 0.4 Max (+2.7V Supply)
0.1 Max. On-Resistance Flatness at +25C
Fast Switching: 10ns Max.
+1.5V to +3.6V Single-Supply Operation
TTL/CMOS-Logic Compatible
25dB Off-Isolation at 100kHz
1nA Max. Off-Leakage at +25C
Packaging (Pb-free available):
5-pin Small Compact SOT-23
6-pin Ultra Compact Thin Dual in-line Flat No Lead TDFN
Applications
Cellular Phones Communications Circuits
Battery-Operated Equipment DSL Modems
Audio and Video Signal Routing PCMCIA Cards
Description
PI3A4626 is a single-pole/single-throw (SPST) normally open
(NO) analog switch that operates from a single +1.5V to +3.6V
supply.
The switch has 0.4 Max On-Resistance (R
ON
), with 0.1 Max
R
ON
flatness over the analog signal range when powered from a
+3.0V supply. Leakage currents are less than 2nA and fast switch-
ing times are less than 10ns.
To minimize PC board area use, the device is available in the ultra
compact TDFN, and the small compact SOT-23 packages.
Functional Block Diagrams/Pin Configurations
Top Views
Switches shown for Logic "0" input
PI3A4626
3.0V, SOT
INY
TM
Single-Supply
0.4 SPST (NO) CMOS Analog Switch
Pin Description
Note:
NO and COM pins are identical and interchangeable. Any pin may be
considered as an input or an output; signals pass.
Truth Table
COM
NO
GND
1
2
3
5
4
V
CC
IN
SOT23
COM
NO
GND
1
2
3
6
4
V
CC
IN
5 N.C.
TDFN
N.C. = No Internal Connection
Input
Switch State
LOW
OFF
HIGH
ON
TDFN SOT-23 Name
Function
1
1
COM Analog Switch, Common
2
2
NO
Analog Switch, Normally Open
3
3
GND Ground
4
4
IN
Digital Control Input
6
5
V
CC
Positive Supply Voltage
5
-
N.C.
No Internal Connection
PI3A4626
3.0V, SOT
INY
Single-Supply
0.4 SPST (NO) CMOS Analog Switch
2
PS8714 12/15/03
Absolute Maximum Ratings
Voltages Referenced to GND
V
CC
......................................................................0.5V to +3.6V
V
IN
, V
COM
, V
NC
, V
NO
(Note 1).................. 0.5V to V
CC
+0.3V
or 30mA, whichever occurs first
Current (any terminal).....................................................200mA
Peak Current, COM, NO, NC
(Pulsed at 1ms, 10% duty cycle).....................................400mA
Note 1: Signals on NC, NO, COM, or IN exceeding V
CC
or GND are clamped by internal diodes. Limit forward diode current to
30mA.
Caution: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a
stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of
this specification is not implied.
Thermal Information
Continuous Power Dissipation
SOT-23 (derate 7.1mW/C above +70C)........................... 0.5W
Storage Temperature ........................................65C to +150C
Lead Temperature (soldering, 10s) ................................. +300C
Electrical Specifications - Single +3.3V Supply
(V
CC
= +3.3V 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Description
Parameters
Test Conditions
Temp.(C) Min.
(1)
Typ.
(2)
Max.
(1)
Units
Analog Switch
Analog Signal Range
(3)
V
ANALOG
Full
0
V
CC
V
On Resistance
R
ON
V
CC
= 2.7V, I
COM
= 100mA,
V
NO
or V
NC
= +1.5V
25
0.4
Full
0.4
On-Resistance Match
Between Channels
(4)
R
ON
25
0.05
Full
0.06
On-Resistance Flatness
(5)
R
FLAT(ON)
V
CC
=2.7V, I
COM
= 100mA,
V
NO
or V
NC
=0.8V, 2.0V
25
0.1
Full
0.1
NO or NC Off Leakage
Current
(6)
I
COM(OFF)
or
I
NC(OFF)
V
CC
=3.3V, V
COM
= 0V,V
NO
or
V
NC
= +2.0V
25
1
1
nA
Full
20
10
COM On Leakage Cur-
rent
(6)
I
COM(ON)
V
CC
=3.3V, V
COM
= +2.0V,
V
NO
or V
NC
= + 2.0V
25
2
2
Full
20
20
3
PS8714 12/15/03
PI3A4626
3.0V, SOT
INY
Single-Supply
0.4 SPST (NO) CMOS Analog Switch
Electrical Specifications - Single +3.3V Supply
(continued)
(V
CC
= + 3.3V 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design.
4. R
ON
=
R
ON
Max. - R
ON
Min.
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25C.
7. Off Isolation = 20log
10
[ V
COM
/ (V
NO
or V
NC
)
]. See Figure 3.
Description
Parameters
Test Conditions
Temp (C) Min.
(1)
Typ.
(2)
Max.
(1)
Units
Logic Input
Input High Voltage
V
IH
Guaranteed logic High Level
Full
1.4
V
Input Low Voltage
V
IL
Guaranteed logic Low Level
0.5
Input Current with Voltage
High
I
INH
V
IN
= 1.4V, all others = 0.5V
1
1
A
Input Current with Voltage
Low
I
INL
V
IN
= 0.5V, all other = 1.4V
1
1
Dynamic
Turn-On Time
t
ON
V
CC
= 3.3V, V
NO
or
V
NC
= 2.0V, Figure 1
25
10
ns
Full
10
Turn-Off Time
t
OFF
25
10
Full
10
Charge Injection
(3)
Q
C
L
= 1nF, V
GEN
= 0V,
R
GEN
= 0, Figure 2
25
50
pC
Off Isolation
(7)
O
IRR
R
L
= 50, f = 100KHz, Figure 3
-25
dB
NC or NO Capacitance
C
(OFF)
f = 1 MHz, Figure 4
130
pF
COM Off Capacitance
C
COM(OFF)
130
COM On Capacitance
C
COM(ON)
f = 1 MHz, Figure 4
270
Supply
Power-Supply Range
V
CC
Full
1.5
3.6
V
Positve Supply Current
I
CC
V
CC
= 3.6V, V
IN
= 0V or V
CC
100
nA
PI3A4626
3.0V, SOT
INY
Single-Supply
0.4 SPST (NO) CMOS Analog Switch
4
PS8714 12/15/03
Electrical Specifications - Single +2.5V Supply
(V
CC
= +2.5V 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design.
4. R
ON
=
R
ON
max. - R
ON
min.
5. Flatness is defined as the difference between the maximum and minimum value of On-resistance measured.
Description
Parameters Test Conditions
Temp.(C) Min.
(1)
Typ.
(2)
Max.
(1)
Units
Analog Switch
Analog Signal Range
(3)
V
ANALOG
0
V
CC
V
On Resistance
R
ON
V
CC
= 2.5V, I
COM
= 8mA,
V
NO
or V
NC
= 1.8V
25
0.4
Full
0.4
On-Resistance Match
Between Channels
(4)
R
ON
V
CC
= 2.5V, I
COM
= 8mA,
V
NO
or V
NC
= 0.8V,1.8V
25
0.05
Full
0.06
On-Resistance Flatness
(5)
R
FLAT(ON)
25
0.1
Full
0.1
Dynamic
Turn-On Time
t
ON
V
CC
= 2.5V,
V
NO
or V
NC
= 1.8V, Figure 1
25
10
ns
Full
15
Turn-Off Time
t
OFF
25
10
Full
10
Charge Injection
(3)
Q
CL = 1nF, V
GEN
= 0V,
R
GEN
= 0V, Figure 2
25
42
pC
Logic Input
Input HIGH Voltage
V
IH
Guaranteed logic high level
Full
1.4
V
Input LOW Voltage
V
IL
Guaranteed logic Low level
Full
0.5
Input HIGH Current
I
INH
V
IN
= 1.4V, all others = 0.5V
Full
1
1
A
Input HIGH Current
I
INL
V
IN
= 0.5V, all others = 1.4V
Full
1
1
5
PS8714 12/15/03
PI3A4626
3.0V, SOT
INY
Single-Supply
0.4 SPST (NO) CMOS Analog Switch
Electrical Specifications - Single +1.8V Supply
(V
CC
= +1.8V 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design.
4. R
ON
=
R
ON
max. - R
ON
min.
5. Flatness is defined as the difference between the maximum and minimum value of On-resistance measured.
Description
Parameters
Test Conditions
Temp.(C) Min.
(1)
Typ.
(2)
Max.
(1)
Units
Analog Switch
Analog Signal Range
(3)
V
ANALOG
0
V
CC
V
On-Resistance
R
ON
V
CC
= 1.8V, I
COM
= 4mA,
V
NO
or V
NC
= 1.5V
25
0.4
Full
0.8
On-Resistance Match
Between Channels
(4)
R
ON
V
CC
= 1.8V, I
COM
= 4mA,
V
NO
or VNC = 0.8V,1.5V
25
0.05
Full
0.06
On-Resistance Flatness
(5)
R
FLAT(ON)
25
0.4
Full
0.6
Dynamic
Turn-On Time
t
ON
V
CC
= 1.8V, V
NO
or V
NC
=
1.5V, Figure 1
25
15
ns
Full
15
Turn-Off Time
t
OFF
25
10
Full
15
Charge Injection
(3)
Q
CL = 1nF, V
GEN
= 0V,
R
GEN
= 0V, Figure 2
25
29
pC
Logic Input
Input HIGH Voltage
V
IH
Guaranteed logic high level
Full
1.4
V
Input LOW Voltage
V
IL
Guaranteed logic Low level
Full
0.5
Input HIGH Current
I
INH
V
IN
= 1.4V, all others = 0.5V
Full
1
1
A
Input HIGH Current
I
INL
V
IN
= 0.5V, all others = 1.4V
Full
1
1
PDF 
ZIP