ChipFind - документация

Электронный компонент: 74LVC2G53DC

Скачать:  PDF   ZIP

Document Outline

1.
General description
The 74LVC2G53 is a high-performance, low-power, low-voltage, Si-gate CMOS device
that provides superior performance to most advanced CMOS compatible TTL families.
The 74LVC2G53 provides one analog multiplexer/demultiplexer with a digital select input
(S), two independent inputs/outputs (B0 and B1), a common input/output (A) and an
active LOW enable input (E). When pin E is HIGH, the switch is turned off.
The 74LVC2G53 can handle both analog and digital signals.
2.
Features
s
Wide supply voltage range from 1.65 V to 5.5 V
s
Very low ON resistance:
x
7.5
(typical) at V
CC
= 2.7 V
x
6.5
(typical) at V
CC
= 3.3 V
x
6
(typical) at V
CC
= 5 V
s
High noise immunity
s
ESD protection:
x
HBM JESD22-A114-C exceeds 2000 V
x
MM JESD22-A115-A exceeds 200 V
x
CDM JESD22-C101-C exceeds 1000 V
s
CMOS low-power consumption
s
Latch-up performance meets requirements of JESD 78 Class I
s
Direct interface with TTL levels
s
Control inputs accepts voltages up to 5 V
s
Multiple package options
s
Specified from
-
40
C to +85
C and from
-
40
C to +125
C
74LVC2G53
2-channel analog multiplexer/demultiplexer
Rev. 01 -- 10 January 2006
Product data sheet
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
2 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
3.
Quick reference data
4.
Ordering information
5.
Marking
Table 1:
Quick reference data
GND = 0 V; t
r
= t
f
2.5 ns; minimum and maximum values at T
amb
=
-
40
C to +85
C;
typical values at T
amb
= 25
C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
t
on
turn-on time
S to A or Bn
C
L
= 50 pF; R
L
= 500
V
CC
= 3.3 V
1.8
3.4
5.0
ns
V
CC
= 5.0 V
1.3
2.6
3.8
ns
E to A or Bn
C
L
= 50 pF; R
L
= 500
V
CC
= 3.3 V
1.2
2.2
3.8
ns
V
CC
= 5.0 V
1.0
1.7
2.6
ns
t
off
turn-off time
S to A or Bn
C
L
= 50 pF; R
L
= 500
V
CC
= 3.3 V
1.1
4.0
5.4
ns
V
CC
= 5.0 V
1.0
2.9
3.8
ns
E to A or Bn
C
L
= 50 pF; R
L
= 500
V
CC
= 3.3 V
2.0
3.7
5.0
ns
V
CC
= 5.0 V
1.3
2.9
3.8
ns
C
i
input capacitance
-
2.5
-
pF
C
S(OFF)
OFF-state capacitance
-
6.0
-
pF
C
S(ON)
ON-state capacitance
-
18
-
pF
Table 2:
Ordering information
Type number
Package
Temperature range Name
Description
Version
74LVC2G53DC
-
40
C to +125
C
VSSOP8
plastic very thin shrink small
outline package; 8 leads;
body width 2.3 mm
SOT765-1
74LVC2G53GT
-
40
C to +125
C
XSON8
plastic extremely thin small outline
package; no leads; 8 terminals;
body 1
1.95
0.5 mm
SOT833-1
Table 3:
Marking
Type number
Marking code
74LVC2G53DC
V53
74LVC2G53GT
V53
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
3 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
6.
Functional diagram
7.
Pinning information
7.1 Pinning
Fig 1.
Logic symbol
Fig 2.
Logic diagram
001aad386
S
A
E
B0
B1
6
7
2
5
1
001aad387
A
B0
S
B1
E
Fig 3.
Pin configuration VSSOP8
Fig 4.
Pin configuration XSON8
53
A
V
CC
E
B0
GND
B1
GND
S
001aad388
1
2
3
4
6
5
8
7
53
B1
B0
V
CC
S
GND
E
A
GND
001aad389
3
6
2
7
1
8
4
5
Transparent top view
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
4 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
7.2 Pin description
8.
Functional description
8.1 Function table
[1]
H = HIGH voltage level;
L = LOW voltage level;
X = don't care;
Z = high-impedance OFF-state.
Table 4:
Pin description
Symbol
Pin
Description
A
1
common A output or input
E
2
enable input (active LOW)
GND
3
ground (0 V)
GND
4
ground (0 V)
S
5
select input
B1
6
independent B1 input or output
B0
7
independent B0 input or output
V
CC
8
supply voltage
Table 5:
Function table
[1]
Input
Channel on
S
E
L
L
B0 to A or A to B0
H
L
B1 to A or A to B1
X
H
Z (switch off)
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
5 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
9.
Limiting values
[1]
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2]
For VSSOP8 package: above 110
C the value of P
tot
derates linearly with 8 mW/K.
For XSON8 package: above 45
C the value of P
tot
derates linearly with 2.4 mW/K.
10. Recommended operating conditions
[1]
To avoid drawing V
CC
current out of terminal A when switch current flows in terminal Bn, the voltage drop
across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal A, no V
CC
current will flow out of terminal Bn. In this case, there is no limit for the voltage drop across the switch.
[2]
Applies to control signal levels.
Table 6:
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Conditions
Min
Max
Unit
V
CC
supply voltage
-
0.5
+6.5
V
V
I
input voltage
[1]
-
0.5
+6.5
V
I
IK
input clamping
current
V
I
<
-
0.5 V or V
I
> V
CC
+ 0.5
-
-
50
mA
I
SK
switch clamping
current
V
I
<
-
0.5 V or V
I
> V
CC
+ 0.5
-
50
mA
V
SW
switch voltage
enable and disable mode
-
0.5
V
CC
+ 0.5 V
I
SW
switch current
V
SW
=
-
0.5 V to (V
CC
+ 0.5 V)
-
50
mA
I
CC
quiescent supply
current
-
100
mA
I
GND
ground current
-
-
100
mA
T
stg
storage temperature
-
65
+
150
C
P
tot
total power
dissipation
T
amb
=
-
40
C to +125
C
[2]
-
300
mW
Table 7:
Recommended operating conditions
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
V
CC
supply voltage
1.65
-
5.5
V
V
I
input voltage
0
-
5.5
V
V
SW
switch voltage
enable and disable
mode
[1]
0
-
V
CC
V
T
amb
ambient temperature
-
40
-
+125
C
t/
V
input transition rise and
fall rate
V
CC
= 1.65 V to 2.7 V
[2]
0
-
20
ns/V
V
CC
= 2.7 V to 5.5 V
[2]
0
-
10
ns/V
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
6 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
11. Static characteristics
Table 8:
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
Unit
T
amb
=
-
40
C to +85
C
[1]
V
IH
HIGH-state input voltage
V
CC
= 1.65 V to 1.95 V
0.65V
CC
-
-
V
V
CC
= 2.3 V to 2.7 V
1.7
-
-
V
V
CC
= 3 V to 3.6 V
2.0
-
-
V
V
CC
= 4.5 V to 5.5 V
0.7V
CC
-
-
V
V
IL
LOW-state input voltage
V
CC
= 1.65 V to 1.95 V
-
-
0.35V
CC
V
V
CC
= 2.3 V to 2.7 V
-
-
0.7
V
V
CC
= 3 V to 3.6 V
-
-
0.8
V
V
CC
= 4.5 V to 5.5 V
-
-
0.3V
CC
V
I
LI
input leakage current
on pin S and pin E;
V
I
= 5.5 V or GND; V
CC
= 5.5 V
-
0.1
2
A
I
S(OFF)
OFF-state leakage current
per channel;
V
SW
= GND and V
O
= V
CC
or V
SW
= V
CC
and V
O
= GND;
V
CC
= 5.5 V; see
Figure 5
-
0.1
5
A
I
S(ON)
ON-state leakage current
per channel;
V
SW
= GND or V
CC
; V
CC
= 5.5 V;
see
Figure 6
-
0.1
5
A
I
CC
quiescent supply current
V
I
= V
CC
or GND;
V
SW
= GND or V
CC
; I
O
= 0 A;
V
CC
= 5.5 V
-
0.1
10
A
I
CC
additional quiescent supply
current
per input pin;
V
I
= V
CC
-
0.6 V; V
SW
= GND or V
CC
;
I
O
= 0 A; V
CC
= 5.5 V
-
5
500
A
C
i
input capacitance
-
2.5
-
pF
C
S(OFF)
OFF-state capacitance
-
6.0
-
pF
C
S(ON)
ON-state capacitance
-
18
-
pF
T
amb
=
-
40
C to +125
C
V
IH
HIGH-state input voltage
V
CC
= 1.65 V to 1.95 V
0.65V
CC
-
-
V
V
CC
= 2.3 V to 2.7 V
1.7
-
-
V
V
CC
= 3 V to 3.6 V
2.0
-
-
V
V
CC
= 4.5 V to 5.5 V
0.7V
CC
-
-
V
V
IL
LOW-state input voltage
V
CC
= 1.65 V to 1.95 V
-
-
0.35V
CC
V
V
CC
= 2.3 V to 2.7 V
-
-
0.7
V
V
CC
= 3 V to 3.6 V
-
-
0.8
V
V
CC
= 4.5 V to 5.5 V
-
0.3V
CC
V
I
LI
input leakage current
on pin S and pin E;
V
I
= 5.5 V or GND; V
CC
= 5.5 V
-
-
10
A
I
S(OFF)
OFF-state leakage current
per channel;
V
SW
= GND and V
O
= V
CC
or V
SW
= V
CC
and V
O
= GND;
V
CC
= 5.5 V; see
Figure 5
-
-
20
A
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
7 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
[1]
Typical values are measured at T
amb
= 25
C.
I
S(ON)
ON-state leakage current
per channel;
V
SW
= GND or V
CC
; V
CC
= 5.5 V;
see
Figure 6
-
-
20
A
I
CC
quiescent supply current
V
I
= V
CC
or GND;
V
SW
= GND or V
CC
; I
O
= 0 A;
V
CC
= 5.5 V
-
-
40
A
I
CC
additional quiescent supply
current
per input pin;
V
I
= V
CC
-
0.6 V; V
SW
= GND or V
CC
;
I
O
= 0 A; V
CC
= 5.5 V
-
-
5000
A
Table 8:
Static characteristics
...continued
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
Unit
V
SW
= V
CC
or GND; V
O
= GND or V
CC.
Fig 5.
Test circuit for measuring switch OFF-state current
V
SW
= V
CC
or GND.
Fig 6.
Test circuit for measuring switch ON-state current
VO
I
SW
I
SW
001aad390
S
A
E
B0
B1
V
CC
GND
switch
switch
1
1
2
2
V
IH
V
IL
S
V
IH
V
IH
E
VSW
V
IL
or V
IH
V
IH
I
SW
001aad391
S
A
E
B0
B1
V
CC
GND
V
IH
V
IL
S
V
IL
V
IL
E
VSW
V
IL
or V
IH
V
IL
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
8 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
Table 9:
Resistance R
on
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see test circuit
Figure 7
.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
T
amb
=
-
40
C to +85
C
[1]
R
ON(rail)
ON resistance (rail)
V
SW
= GND
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
8.7
18
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
7.2
16
I
SW
= 12 mA; V
CC
= 2.7 V
-
7.0
14
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
6.5
12
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
5.9
10
V
SW
= V
CC
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
12
30
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
8.3
20
I
SW
= 12 mA; V
CC
= 2.7 V
-
7.8
18
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
6.7
15
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
5.2
10
R
ON(peak)
ON resistance (peak)
V
SW
= GND to V
CC
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
57
130
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
15
30
I
SW
= 12 mA; V
CC
= 2.7 V
-
13
25
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
9.0
20
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
6.0
15
R
ON(flat)
ON resistance (flatness)
V
SW
= GND to V
CC
; see
Figure 9
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
100
-
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
17
-
I
SW
= 12 mA; V
CC
= 2.7 V
-
10
-
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
5
-
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
3
-
T
amb
=
-
40
C to +125
C
R
ON(rail)
ON resistance (rail)
V
SW
= GND
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
-
27
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
-
24
I
SW
= 12 mA; V
CC
= 2.7 V
-
-
21
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
-
18
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
-
15
V
SW
= V
CC
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
-
45
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
-
30
I
SW
= 12 mA; V
CC
= 2.7 V
-
-
27
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
-
23
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
-
15
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
9 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
[1]
Typical values are measured at T
amb
= 25
C and nominal V
CC
.
R
ON(peak)
ON resistance (peak)
V
SW
= GND to V
CC
I
SW
= 4 mA; V
CC
= 1.65 V to 1.95 V
-
-
130
I
SW
= 8 mA; V
CC
= 2.3 V to 2.7 V
-
-
55
I
SW
= 12 mA; V
CC
= 2.7 V
-
-
35
I
SW
= 24 mA; V
CC
= 3 V to 3.6 V
-
-
25
I
SW
= 32 mA; V
CC
= 4.5 V to 5.5 V
-
-
20
Table 9:
Resistance R
on
...continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see test circuit
Figure 7
.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
R
ON
= V
SW
/ I
SW
Fig 7.
Test circuit for measuring switch ON resistance
ISW
VSW
001aad392
S
A
E
B0
B1
V
CC
GND
switch
switch
1
1
2
2
V
IH
V
IL
S
V
IL
V
IL
E
VSW
V
IL
or V
IH
V
IL
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
10 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
(1) V
CC
= 1.8 V
(2) V
CC
= 2.5 V
(3) V
CC
= 2.7 V
(4) V
CC
= 3.3 V
(5) V
CC
= 5.0 V
(6) T
amb
= 25
C
Fig 8.
Typical switch ON resistance as a function of input voltage
V
SW
(V)
0
5
4
2
3
1
001aad406
20
10
30
40
R
ON
(
)
0
(1)
(3)
(4)
(5)
(2)
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
11 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
(1) T
amb
= 125
C
(2) T
amb
= 85
C
(3) T
amb
= 25
C
(4) T
amb
=
-
40
C
(1) T
amb
= 125
C
(2) T
amb
= 85
C
(3) T
amb
= 25
C
(4) T
amb
=
-
40
C
a. V
CC
= 1.8 V
b. V
CC
= 2.5 V
(1) T
amb
= 125
C
(2) T
amb
= 85
C
(3) T
amb
= 25
C
(4) T
amb
=
-
40
C
(1) T
amb
= 125
C
(2) T
amb
= 85
C
(3) T
amb
= 25
C
(4) T
amb
=
-
40
C
c. V
CC
= 2.7 V
d. V
CC
= 3.3 V
Fig 9.
Switch ON resistance as a function of switch voltage
V
SW
(V)
0
5
4
2
3
1
001aad410
40
20
60
80
R
ON
(
)
0
(1)
(2)
(3)
(4)
V
SW
(V)
0
5
4
2
3
1
001aad407
8
4
12
16
R
ON
(
)
0
(1)
(2)
(3)
(4)
V
SW
(V)
0
5
4
2
3
1
001aad408
8
4
12
16
R
ON
(
)
0
(1)
(2)
(3)
(4)
V
SW
(V)
0
5
4
2
3
1
001aad409
8
4
12
16
R
ON
(
)
0
(1)
(2)
(3)
(4)
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
12 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
12. Dynamic characteristics
Table 10:
Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V);
test circuit
Figure 12
.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
T
amb
=
-
40
C to +85
C
[1]
t
PHL
HIGH-to-LOW
propagation delay
see
Figure 10
A to Bn or Bn to A
V
CC
= 1.65 V to 1.95 V
-
-
2
ns
V
CC
= 2.3 V to 2.7 V
-
-
1.2
ns
V
CC
= 2.7 V
-
-
1.0
ns
V
CC
= 3 V to 3.6 V
-
-
0.8
ns
V
CC
= 4.5 V to 5.5 V
-
-
0.6
ns
t
PLH
LOW-to-HIGH
propagation delay
see
Figure 10
A to Bn or Bn to A
V
CC
= 1.65 V to 1.95 V
-
-
2
ns
V
CC
= 2.3 V to 2.7 V
-
-
1.2
ns
V
CC
= 2.7 V
-
-
1.0
ns
V
CC
= 3 V to 3.6 V
-
-
0.8
ns
V
CC
= 4.5 V to 5.5 V
-
-
0.6
ns
t
on
turn-on time
see
Figure 11
S to A or Bn
V
CC
= 1.65 V to 1.95 V
2.6
6.7
10.3
ns
V
CC
= 2.3 V to 2.7 V
1.9
4.1
6.4
ns
V
CC
= 2.7 V
1.9
4.0
5.5
ns
V
CC
= 3 V to 3.6 V
1.8
3.4
5.0
ns
V
CC
= 4.5 V to 5.5 V
1.3
2.6
3.8
ns
E to A or Bn
V
CC
= 1.65 V to 1.95 V
1.9
4.0
7.3
ns
V
CC
= 2.3 V to 2.7 V
1.4
2.5
4.4
ns
V
CC
= 2.7 V
1.1
2.6
3.9
ns
V
CC
= 3 V to 3.6 V
1.2
2.2
3.8
ns
V
CC
= 4.5 V to 5.5 V
1.0
1.7
2.6
ns
t
off
turn-off time
see
Figure 11
S to A or Bn
V
CC
= 1.65 V to 1.95 V
2.1
6.8
10.0
ns
V
CC
= 2.3 V to 2.7 V
1.4
3.7
6.1
ns
V
CC
= 2.7 V
1.4
4.9
6.2
ns
V
CC
= 3 V to 3.6 V
1.1
4.0
5.4
ns
V
CC
= 4.5 V to 5.5 V
1.0
2.9
3.8
ns
E to A or Bn
V
CC
= 1.65 V to 1.95 V
2.3
5.6
8.6
ns
V
CC
= 2.3 V to 2.7 V
1.2
3.2
4.8
ns
V
CC
= 2.7 V
1.4
4.0
5.2
ns
V
CC
= 3 V to 3.6 V
2.0
3.7
5.0
ns
V
CC
= 4.5 V to 5.5 V
1.3
2.9
3.8
ns
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
13 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
[1]
Typical values are measured at T
amb
= 25
C and nominal V
CC
.
T
amb
=
-
40
C to +125
C
t
PHL
HIGH-to-LOW
propagation delay
see
Figure 10
A to Bn or Bn to A
V
CC
= 1.65 V to 1.95 V
-
-
2.5
ns
V
CC
= 2.3 V to 2.7 V
-
-
1.5
ns
V
CC
= 2.7 V
-
-
1.25
ns
V
CC
= 3 V to 3.6 V
-
-
1.0
ns
V
CC
= 4.5 V to 5.5 V
-
-
0.8
ns
t
PLH
LOW-to-HIGH
propagation delay
see
Figure 10
A to Bn or Bn to A
V
CC
= 1.65 V to 1.95 V
-
-
2.5
ns
V
CC
= 2.3 V to 2.7 V
-
-
1.5
ns
V
CC
= 2.7 V
-
-
1.25
ns
V
CC
= 3 V to 3.6 V
-
-
1.0
ns
V
CC
= 4.5 V to 5.5 V
-
-
0.8
ns
t
on
turn-on time
see
Figure 11
S to A or Bn
V
CC
= 1.65 V to 1.95 V
2.6
-
12.9
ns
V
CC
= 2.3 V to 2.7 V
1.9
-
8.0
ns
V
CC
= 2.7 V
1.8
-
7.0
ns
V
CC
= 3 V to 3.6 V
1.8
-
6.3
ns
V
CC
= 4.5 V to 5.5 V
1.3
4.8
ns
E to A or Bn
V
CC
= 1.65 V to 1.95 V
1.9
-
9.2
ns
V
CC
= 2.3 V to 2.7 V
1.4
-
5.5
ns
V
CC
= 2.7 V
1.1
-
4.9
ns
V
CC
= 3 V to 3.6 V
1.2
-
4.8
ns
V
CC
= 4.5 V to 5.5 V
1.0
-
3.3
ns
t
off
turn-off time
see
Figure 11
S to A or Bn
V
CC
= 1.65 V to 1.95 V
2.1
-
12.5
ns
V
CC
= 2.3 V to 2.7 V
1.4
-
7.7
ns
V
CC
= 2.7 V
1.4
-
7.8
ns
V
CC
= 3 V to 3.6 V
1.1
-
6.8
ns
V
CC
= 4.5 V to 5.5 V
1.0
4.8
ns
E to A or Bn
V
CC
= 1.65 V to 1.95 V
2.3
-
11.0
ns
V
CC
= 2.3 V to 2.7 V
1.2
-
6.0
ns
V
CC
= 2.7 V
1.4
-
6.5
ns
V
CC
= 3 V to 3.6 V
2.0
-
6.3
ns
V
CC
= 4.5 V to 5.5 V
1.3
-
4.8
ns
Table 10:
Dynamic characteristics
...continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V);
test circuit
Figure 12
.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
14 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
13. Waveforms
Measurement points are given in
Table 11
.
Logic levels: V
OL
and V
OH
are typical output voltage drop that occur with the output load.
Fig 10. Input (Bn or A) to output (A or Bn) propagation delays
Measurement points are given in
Table 11
.
Logic levels: V
OL
and V
OH
are typical output voltage drop that occur with the output load.
Fig 11. Turn-on and turn-off times
Table 11:
Measurement points
Supply voltage
Input
Output
V
CC
V
M
V
M
V
X
V
Y
1.65 V to 2.7 V
0.5V
CC
0.5V
CC
V
OL
+ 0.15 V
V
OH
-
0.15 V
2.7 V to 5.5 V
0.5V
CC
0.5V
CC
V
OL
+ 0.3 V
V
OH
-
0.3 V
t
PLH
t
PHL
V
M
V
M
V
M
V
M
GND
V
I
V
OH
V
OL
Bn or A
input
A or Bn
output
001aac361
V
M
V
I
GND
V
CC
V
OL
V
OH
GND
S, E input
output
LOW to OFF
OFF to LOW
output
HIGH to OFF
OFF to HIGH
V
M
001aad393
V
M
t
on
t
off
t
on
V
X
V
Y
switch
disabled
switch
enabled
switch
enabled
A, Bn
A, Bn
t
off
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
15 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
14. Additional dynamic characteristics
Test data is given in
Table 12
.
Definitions test circuit:
R
T
= termination resistance (should be equal to output impedance Z
o
of the pulse generator).
C
L
= load capacitance (including jig and probe capacitance).
R
L
= load resistance.
V
EXT
= external voltage for measuring switching times.
Fig 12. Load circuitry for switching times
Table 12:
Test data
Supply voltage
Input
Load
V
EXT
V
CC
V
I
t
r
, t
f
C
L
R
L
t
PLH
, t
PHL
t
on
, t
off
HIGH to OFF
OFF to HIGH
LOW to OFF
OFF to LOW
1.65 V to 1.95 V
V
CC
2.0 ns
30 pF
1 k
open
GND
2
V
CC
2.3 V to 2.7 V
V
CC
2.0 ns
30 pF
500
open
GND
2
V
CC
2.7 V
V
CC
2.5 ns
50 pF
500
open
GND
2
V
CC
3 V to 3.6 V
V
CC
2.5 ns
50 pF
500
open
GND
2
V
CC
4.5 V to 5.5 V
V
CC
2.5 ns
50 pF
500
open
GND
2
V
CC
V
EXT
V
CC
V
I
V
O
mna616
DUT
CL
RT
RL
RL
PULSE
GENERATOR
Table 13:
Additional dynamic characteristics
At recommended operating conditions; typical values measured at T
amb
= 25
C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
THD
total harmonic
distortion
f
i
= 600 Hz to 20 kHz;
R
L
= 600
; C
L
= 50 pF;
V
i
= 0.5 V (p-p); see
Figure 13
V
CC
= 1.65 V
-
0.260
-
%
V
CC
= 2.3 V
-
0.078
-
%
V
CC
= 3.0 V
-
0.078
-
%
V
CC
= 4.5 V
-
0.078
-
%
f
(-3dB)
-
3 dB frequency
response
R
L
= 50
; C
L
= 5 pF;
see
Figure 14
[1]
V
CC
= 1.65 V
-
200
-
MHz
V
CC
= 2.3 V
-
300
-
MHz
V
CC
= 3.0 V
-
300
-
MHz
V
CC
= 4.5 V
-
300
-
MHz
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
16 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
[1]
Adjust f
i
voltage to obtain 0 dBm level at output. Increase f
i
frequency until dB meter reads
-
3 dB.
[2]
Adjust f
i
voltage to obtain 0 dBm level at input.
[3]
Definition: Q
inj
=
V
O
C
L
. Guaranteed by design.
OFF(ft)
OFF-state
feed-through
attenuation
R
L
= 50
; C
L
= 5 pF;
f
i
= 10 MHz; see
Figure 15
[2]
V
CC
= 1.65 V
-
-
42
-
dB
V
CC
= 2.3 V
-
-
42
-
dB
V
CC
= 3.0 V
-
-
40
-
dB
V
CC
= 4.5 V
-
-
40
-
dB
V
ct(sw-sw)
crosstalk between
switches
R
L
= 50
; C
L
= 5 pF;
f
i
= 10 MHz; see
Figure 16
V
CC
= 1.65 V
-
-
68
-
dBV
V
CC
= 2.3 V
-
-
70
-
dBV
V
CC
= 3.0 V
-
-
70
-
dBV
V
CC
= 4.5 V
-
-
70
-
dBV
Q
inj
charge injection
C
L
= 0.1 nF; V
gen
= 0 V;
R
gen
= 0
; f
i
= 1 MHz;
R
L
= 1 M
; see
Figure 17
[3]
V
CC
= 1.8 V
-
< 0.003
-
pC
V
CC
= 2.5 V
-
0.004
-
pC
V
CC
= 3.3 V
-
0.0045
-
pC
V
CC
= 4.5 V
-
0.0045
-
pC
V
CC
= 5.5 V
-
0.0045
-
pC
Fig 13. Test circuit for measuring total harmonic distortion
Table 13:
Additional dynamic characteristics
...continued
At recommended operating conditions; typical values measured at T
amb
= 25
C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
D
001aad394
600
10
F
0.1
F
S
A
B0
B1
V
CC
0.5V
CC
GND
CL
RL
switch
switch
1
1
2
2
V
IH
V
IL
S
V
IL
V
IL
E
fi
V
IL
or V
IH
E
V
IL
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
17 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
Fig 14. Test circuit for measuring the frequency response when switch is in ON-state
Fig 15. Test circuit for measuring feed-through attenuation when switch is in OFF-state
Fig 16. Test circuit for measuring crosstalk between switches
dB
001aad395
50
0.1
F
S
A
E
B0
B1
V
CC
0.5V
CC
GND
CL
RL
switch
switch
1
1
2
2
V
IH
V
IL
S
V
IL
V
IL
E
fi
V
IL
or V
IH
V
IL
dB
001aad396
50
RL
0.1
F
S
A
E
B0
B1
V
CC
0.5V
CC
0.5V
CC
GND
CL
RL
switch
switch
1
1
2
2
V
IH
V
IL
S
V
IH
V
IH
E
fi
V
IL
or V
IH
V
IH
dB
001aad397
50
0.1
F
S
A
E
B0
B1
V
CC
0.5V
CC
GND
CL
RL
0.5V
CC
RL
V
IH
V
IL
S
20log10(V
B1
/V
I
)
20log10(V
B0
/V
I
)
test condition
V
IL
V
IL
E
fi
V
IL
or V
IH
V
IL
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
18 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
V
O
= output voltage variation
R
gen
= generator resistance
V
gen
= generator voltage
Fig 17. Test circuit for measuring charge injection
001aad398
S
A
B0
B1
RL
CL
V
CC
GND
Rgen
Vgen
switch
1
2
logic
input
(S)
V
O
E
V
IL
001aac478
V
O
off
on
off
logic
input
V
O
(S)
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
19 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
15. Package outline
Fig 18. Package outline SOT765-1 (VSSOP8)
UNIT
A1
A
max.
A2
A3
bp
L
HE
Lp
w
y
v
c
e
D
(1)
E
(2)
Z
(1)
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
JEITA
mm
0.15
0.00
0.85
0.60
0.27
0.17
0.23
0.08
2.1
1.9
2.4
2.2
0.5
3.2
3.0
0.4
0.1
8
0
0.13
0.1
0.2
0.4
DIMENSIONS (mm are the original dimensions)
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
0.40
0.15
Q
0.21
0.19
SOT765-1
MO-187
02-06-07
w
M
bp
D
Z
e
0.12
1
4
8
5
A2
A1
Q
Lp
(A3)
detail X
A
L
HE
E
c
v
M
A
X
A
y
2.5
5 mm
0
scale
VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm
SOT765-1
1
pin 1 index
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
20 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
Fig 19. Package outline SOT833-1 (XSON8)
terminal 1
index area
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
JEITA
SOT833-1
- - -
MO-252
- - -
SOT833-1
04-07-22
04-11-09
DIMENSIONS (mm are the original dimensions)
XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm
D
E
e
1
e
A
1
b
L
L
1
e
1
e
1
0
1
2 mm
scale
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
UNIT
mm
0.25
0.17
2.0
1.9
0.35
0.27
A
1
max
b
E
1.05
0.95
D
e
e
1
L
0.40
0.32
L
1
0.5
0.6
A
(1)
max
0.5
0.04
1
8
2
7
3
6
4
5
8
(2)
4
(2)
A
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
21 of 23
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
16. Abbreviations
17. Revision history
Table 14:
Abbreviations
Acronym
Description
CMOS
Complementary Metal Oxide Semiconductor
TTL
Transistor Transistor Logic
HBM
Human Body Model
ESD
ElectroStatic Discharge
MM
Machine Model
CDM
Charged Device Model
DUT
Device Under Test
Table 15:
Revision history
Document ID
Release date
Data sheet status
Change notice
Doc. number
Supersedes
74LVC2G53_1
20060110
Product data sheet
-
-
-
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
74LVC2G53_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 01 -- 10 January 2006
22 of 23
18. Data sheet status
[1]
Please consult the most recently issued data sheet before initiating or completing a design.
[2]
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
[3]
For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
19. Definitions
Short-form specification -- The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition -- Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information -- Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
makes no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
20. Disclaimers
Life support -- These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Right to make changes -- Philips Semiconductors reserves the right to
make changes in the products - including circuits, standard cells, and/or
software - described or contained herein in order to improve design and/or
performance. When the product is in full production (status `Production'),
relevant changes will be communicated via a Customer Product/Process
Change Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
21. Trademarks
Notice -- All referenced brands, product names, service names and
trademarks are the property of their respective owners.
22. Contact information
For additional information, please visit: http://www.semiconductors.philips.com
For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
Level
Data sheet status
[1]
Product status
[2] [3]
Definition
I
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips
Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
Koninklijke Philips Electronics N.V. 2006
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner. The information presented in this document does
not form part of any quotation or contract, is believed to be accurate and reliable and may
be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under
patent- or other industrial or intellectual property rights.
Date of release: 10 January 2006
Document number: 74LVC2G53_1
Published in The Netherlands
Philips Semiconductors
74LVC2G53
2-channel analog multiplexer/demultiplexer
23. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3
Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
5
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
7
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
7.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
7.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
8
Functional description . . . . . . . . . . . . . . . . . . . 4
8.1
Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4
9
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5
10
Recommended operating conditions. . . . . . . . 5
11
Static characteristics. . . . . . . . . . . . . . . . . . . . . 6
12
Dynamic characteristics . . . . . . . . . . . . . . . . . 12
13
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
14
Additional dynamic characteristics . . . . . . . . 15
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19
16
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 21
17
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 21
18
Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 22
19
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
20
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
21
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
22
Contact information . . . . . . . . . . . . . . . . . . . . 22