Äîêóìåíòàöèÿ è îïèñàíèÿ www.docs.chipfind.ru

BU TUNERS

DATA SHEET

Preliminary specification
File under BU Tuners, DC03

1996 Jul 09

FI1216MF MK2
Desktop video tuner
multi system CCIR L/L' and B/G

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

FEATURES

Systems CCIR L/L' and B/G

True 5 V device (low power dissipation)

Full frequency range from channel 2 (48.25 MHz) to
channel 69 (855.25 MHz)

PLL controlled tuning

True-synchronous vision IF demodulator (PLL)

Demodulated video output, AF sound output, second
sound IF output

C-bus control of tuning, address selection, AFC status

information

Complies with European regulations on radiation, signal
handling and immunity

("CENELEC 55020, 55013")

Small horizontally mounted metal housing.

DESCRIPTION

The FI1200MK2 family of front ends are designed to meet
a wide range of RF applications in the PC Multi-Media
environment.

The FI1216MF MK2 type are available with a single 75

input for TV reception. The input connector is available in
either standard phono (female socket) or IEC (female
socket).

The tuning and bandswitching are performed through the
built-in digitally controlled I

C-bus. All front ends meet the

input immunity and radiation requirements of CENELEC.

The FI1216MF MK2 consists of a tuner section and an IF
section, which are all designed on a single PCB. The
front-end is assembled in a metal housing made of a
rectangular tin plated steel frame with front and rear covers
which have soldered contacts to the frame. A single phono
or IEC aerial socket is mounted on one side of the frame.
All other connections are made via pins at the bottom.

The tuner section is equipped with 3 tuned RF MOSFET
input stages, with a 3-band mixer-oscillator IC, containing
the oscillators, mixers and IF amplifier. Tuning and band
switching in the tuner section are done with a digital
programmable PLL tuning system. This enables tuning
with step-size programmable between 31.25, 50.0 or
62.5 kHz. A DC-DC converter is built around the PLL
synthesizer IC to provide the tuning voltage, thus making
the FI1216MF MK2 front-end a true 5 V device.

The IF section uses a true-synchronous vision IF
demodulator (PLL) with an intercarrier SAW filter in front of
it. The analog AFC voltage is fed to the 5-level A/D
converter in the PLL tuning IC, so that the AFC status can
be read via the I

C-bus.

ORDERING INFORMATION

TYPE

DESCRIPTION

CATALOGUE NUMBERS

FI1216MF MK2/HM/PH

standard phono

3139 147 13571

FI1216MF MK2/HM/IEC

IEC

3139 147 13581

MARKING

The following items of information are printed on a sticker
that is on the top cover of the tuner:

Type number

Code number

Origin letter of factory

Change code

Year and week code.

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

INTERMEDIATE FREQUENCIES

Note

1. The oscillator frequency is above the input signal frequency.

CHANNEL COVERAGE

PINNING

SYSTEM

FREQUENCY

(1)

(MHz)

PAL B/G

Picture carrier

38.90

33.95

38.90

Colour

34.47

38.38

34.47

Sound 1

32.40

40.45

33.40

Sound 2

33.16

NICAM

33.05

39.80

33.05

BAND

CHANNELS

Low band

48.25 to 170.00 MHz

Mid band

170.00 to 450.00 MHz

High band

450.00 to 855.25 MHz

SYMBOL

PIN

DESCRIPTION

tuning voltage (monitor)

supply voltage tuner section +5 V

SCL

C-bus serial clock

SDA

C-bus serial data

C-bus address select

n.c.

not connected

IF sound output

second IF sound output

CVBS

Composite Video Baseband Signal output

supply voltage IF section +5 V

AF sound output

TH1, TH2, TH3 and TH4

mounting tags (ground)

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

BLOCK DIAGRAM

handbook, full pagewidth

LOW BAND

HIGH BAND

MID BAND

CCA217

HIGH

OSC.

BAND

MID

OSC.

BAND

LOW

OSC.

BAND

PLL

DC - DC

MIXER - OSCILLATOR IC

PLL DEMODULATOR

AGC

FILTER

TRAP

DEMODULATOR

VCO

77.8/67.9 MHz

SDA

SCL

ADC

(

5 V)

(+5 V)

2nd IF

sound

output

CVBS

sound

output

Fig.1 Electrical block diagram.

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

LIMITING VALUES

Limiting values under operational conditions

The tuner can be guaranteed to function properly under the following conditions.

Notes

1. Sinusoidal ripple voltage superimposed on the 5 V supply voltage in the frequency range of 20 Hz to 500 kHz.

Criteria for TV interference >57 dB.

2. For detailed information about the address decoding, refer to Chapter "Application information".

SYMBOL

PARAMETER

PIN

MIN.

TYP.

MAX.

UNIT

supply voltage

4.75

5.00

5.25

S(ripple)

peak-to-peak ripple voltage susceptibility
(at 5 V

5%); note 1

20 Hz to 100 kHz

>100 kHz to 500 kHz

supply current

120

SCL

SCL bus input voltage

0.3

+5.25

SDA

SDA bus input voltage

0.3

+5.25

SDA

SDA bus current (open collector)

address select voltage; note 2

+5.25

IF sound output load impedance:

0.5

CVBS

Composite Video Baseband Signal load
impedance:

load time constant

100

IF supply voltage

4.75

5.0

5.25

IF(ripple)

peak-to-peak ripple voltage susceptibility
(at 5 V

5%); note 1

20 Hz to 100 kHz

>100 kHz to 500 kHz

IF supply current

100

AF sound output load impedance:

1.0

0.6

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Environmental conditions

OVERALL PERFORMANCE

Conditional data

Unless otherwise specified, all electrical values for Chapter "Overall performance" apply at the following conditions.

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

Non-operational conditions

amb

ambient temperature

+85

relative humidity

100

bump acceleration

25 g

245

m/s

shock acceleration

50 g

490

m/s

vibration amplitude

10 to 55 Hz

0.35

Operational conditions

amb

ambient temperature

+60

relative humidity

SYMBOL

PARAMETER

VALUE

UNIT

amb

ambient temperature

relative humidity

supply voltage (tuner and IF section)

0.125

CVBS

video output load impedance (DC)

>75

IF sound output load impedance (DC)

>500

pre-heating time (+5 V at pin 24)

minute

S(AE)

aerial source impedance (unbalanced)

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

TUNER SECTION

Tuner characteristics

For detailed information about the PLL programming, refer to Chapter "Application information".

The desktop video tuner is guaranteed to function properly within the specified operational conditions, but a certain
deterioration of performance parameters may occur at the limits of the operational conditions.

Test equipment

EQUIPMENT

PARAMETER

VALUE

UNIT

DC voltmeter

input impedance

Oscilloscope

input impedance:

resistance

capacitance

<15

Spectrum analyzer

input impedance

FET probe

input impedance:

resistance

capacitance

3.5

output impedance

voltage gain

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

handbook, full pagewidth

PROBE

OUT

output

12 13 14 15

TP2

TP3

22 23 24 25

aerial

connector

SCL

SDA

BU2

51
nF

BU6

BU2

BU4

BU5

5 V

TEST JIG

(1)

(2)

video

out

CCA010

10 nF

Fig.2 Typical test set-up.

(1) BU4 loaded with 75

(2) 50

s de-emphasis.

SA = spectrum analyzer.

P = FET probe.

DA = distortion analyzer.

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Definitions of test signals (see Fig.2)

Note

1. Line 17 and 330 shall always contain a composite video signal (ITS lines).

TEST SIGNAL

FREQ.

(MHz)

AMPLITUDE

MODULATION

VIDEO

AUDIO

A0: unmodulated vision
carrier

480.25

60 dB

A1: L system signal with
video modulation; see note 1

480.25

60 dB

(peak white)

100% (sync. level at 0%)
2T pulse and bar

A2: B/G system signal with
video modulation

480.25

60 dB

(top sync)

100% (rest carrier 10%)
2T pulse and bar

A3: B/G system signal with
video modulation

480.25

60 dB

100% (rest carrier 10%)
15625 kHz horizontal
frequency square wave

B1: unmodulated main sound
carrier B/G system

485.75

13 dB w.r.t. A2

B2: AM modulated sound
carrier L system

486.75

10 dB w.r.t.

A0 to A1

m = 0.54; modulation
frequency 1 kHz

B3 FM modulated main
sound carrier B/G system

485.75

13 dB w.r.t. A2

1 kHz; modulation frequency
deviation

27 kHz;

s pre-emphasis

B4: unmodulated second
sound carrier B/G system

486.10

20 dB w.r.t.

A0 to A1

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Aerial input characteristics

General characteristics

SYMBOL

PARAMETER

CONDITIONS

MIN.

MAX.

UNIT

VSWR

reflection coefficient

referred to 75

impedance

(worst case on or between picture
and sound carrier at maximum gain)

PSM

surge protection voltage

ant

antenna connection disturbance
voltage

<1.75 GHz

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

frequency range:

low band

48.25

168.25

MHz

mid band

175.25

447.25

MHz

high band

455.25

855.25

MHz

margin:

for low band

1.5

MHz

for mid/high band

MHz

image rejection (nominal gain to
10 dB gain reduction):

low band

mid band

<300 MHz

mid band

>300 MHz

high band

IF rejection (picture)

IF susceptibility:

E2 to E12

E21 to E69

sound-chrominance moiré rejection:

off-air

up to 40 dB gain control

UHF

up to 30 dB minimum gain
control

cross modulation:

in-channel

in-band

low band (n

mid band (n

high band (n

out of band

100

breakthrough susceptibility:

E2 to E12; E21 to E69

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Note

1. All the pins of the desktop video tuner are protected against electrostatic discharge (ESD) up to 2 kV. The product is

classified in category B

(``MIL-STD-883C").

osc

oscillator voltage at all pins

oscillators lock-in time

charge pump set logic HIGH

150

the video signal-to-sound
interference ratio with the tuner
exposed to sound signals in the
audio frequency range
100 Hz to 10 kHz and sound
pressure levels up to 105 dB
(20

Pa)

ESD

electrostatic discharge (ESD)
on all pins

note 1

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Video and audio characteristics (see Fig.2)

PARAMETER

TEST SIGNAL

TEST

POINT

MIN.

TYP.

MAX.

UNIT

CVBS characteristics:

video amplitude signal at pin 23

A1 (peak-to-peak value)

BU4

0.7

0.9

1.1

DC level sync pulse at pin 23

BU4

0.35

Video amplitude drop with respect to modulation
0.1 MHz at T

amb

= 45

at 2 MHz

BU4

1.5

+1.5

at 3 MHz

BU4

2.5

+1.5

at 4 MHz

BU4

4.0

+2.0

at 4.43 MHz

BU4

6.0

+2.0

Sound carrier rejection

A1 + B3

BU4

Residual 40.4 MHz signal in video channel:
level of 1.5 MHz

A1 + B3

BU4

Residual 77.8 MHz signal in video channel

BU4

Second IF sound output level at level of 5.5 MHz

A2 + B1

BU5

Test on 2T pulse at T

amb

= 45

2T pulse/bar response for L mode

BU4

3.0

+3.0

2T pulse response for L mode

BU4

+3.0

2T pulse/bar response for B/G mode

BU4

4.5

+3.0

2T pulse response for B/G mode

BU4

+5.0

CVBS S/N (unweighted)

A1 + B1

BU4

Gain limited sensitivity at 1 dB reduction
of video output

BU4

B/G audio characteristics:

AF output level measured via LP 20 kHz filter,
RMS detector, 50

s de-emphasis

A2 + B3

BU6

0.25

0.35

0.50

THD (Total Harmonic Distortion) measured via
LP 20 kHz filter, RMS detector, 50

de-emphasis

A2 + B3

BU6

0.15

0.5

S/N measured via CCIR filter, peak
CCIR detector, 50

s de-emphasis

A2 (6 kHz sine wave,
black-to-white) + B3

BU6

L/L' audio characteristics:

AF output level measured via LP 20 kHz filter,
RMS detector

A1 + B2

BU6

0.40

0.50

0.60

THD (Total Harmonic Distortion) measured via
LP 20 kHz filter, RMS detector

A1 + B2

BU6

0.7

1.5

S/N measured via CCIR filter, peak
CCIR detector

A1 (black) + B2

BU6

AM suppression ratio

A1 + B2

BU6

Aerial input level for S/N = 45 dB:

system B/G

A2 (black) + B3

BU4

system L

A1 (black) + B2

BU4

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Digital AFC status

PARAMETER

CONDITIONS

FREQUENCY

(kHz)

DIGITAL

READ-OUT

ADC word at I

C-bus during read operation

input voltage at pin 10: 0.0 to 0.15V

125

input voltage at pin 10: 0.15 to 0.30V

62.5

input voltage at pin 10: 0.30 to 0.45V

input voltage at pin 10: 0.45 to 0.60V

+62.5

input voltage at pin 10: 0.60 to 1.00V

+125

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

APPLICATION INFORMATION

A detailed description of the I

C-bus specification, with applications, is given in brochure

``The I

C-bus and how to

use it''. This brochure may be ordered using the code number 9398 393 40011.

WRITE mode

Note

1. A = Acknowledge.

DDRESS SELECTION

= +5 V (PLL supply voltage)

Note

1. If the AS pin is left floating, the internal bias will automatically set the address to C2.

ROGRAMMABLE DIVIDER SETTINGS

(

BYTES

AND

Divider ratio:

N = 16

× {

RF(pc)

+ f

IF(pc)

}, where (pc) is picture carrier and f

and f

are expressed in MHz

osc

(MHz).

N = (8192

n13) + (4096

n12) + (2048

n11) + (1024

n10) + (512

n9) + (256

n8) + (128

n7) + (64

n6) +

(32

n5) + (16

n4) + (8

n3) + (4

n2) + (2

n1) + n0

ONTROL BYTE

Charge pump settings:

CP = 1, for fast tuning

CP = 0, for moderate speed tuning with slightly better residual oscillator FM.

Test mode settings:

T2 = T1 = 0; T0 = 1, for normal operation.

PLL disabling:

OS = 0, for normal operation

OS = 1, for switching the charge pump to the high impedance state.

BYTE

BITS

MSB

LSB

(1)

Address byte

MA1

MA0

Program divider byte 1

n14

n13

n12

n11

n10

Program divider byte 2

Control information byte 1

RSA

RSB

Control information byte 2

MA1

MA0

ADDRESS

VOLTAGE AT PIN 15 (see note 1)

0 to 0.1V

0.2 to 0.3V

0.4 to 0.6V

0.9V

to V

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Ratio select bits

ORTS BYTE

Notes

1. X = don't care; P0 to P7 are output ports on the PLL device.

2. P3 is a system switch output for customer applications.

ELEGRAM EXAMPLES

(WRITE

MODE

)

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop.

Start - Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Stop.

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Where:

Start = start condition

Adb = address byte

Ack = acknowledge

Db1 = divider byte 1

Db2 = divider byte 2

Cb = control byte

Pb = ports byte

Stop = stop condition.

RSA

RSB

STEP SIZE

50 kHz

31.25 kHz (for slow picture search)

62.5 kHz (for normal picture search)

BAND/

SYSTEM

BIT (see note 1)

Band switching

Low band

see note 2

Mid band

High band

System switching

see note 2

B/G

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Remark: for channel selection involving band switching, and to ensure smooth tuning to the desired channel without
causing unnecessary charge pump action, it is recommended to consider the difference between wanted channel
frequency (f

) and the current channel frequency (f

If f

> f

, use telegram as:

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop.

If f

> f

, use telegram as:

Start - Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Unnecessary charge pump action will result in very low tuning voltage (V

0 V) which may drive the oscillator to extreme

conditions.

READ mode

The in-lock can be read by setting the R/W bit to 1.

Notes

1. POR = Power On Reset. POR is internally set to 1 in case V

drops below 3 V. The POR bit is reset when an end of

data is detected by the PLL IC.

2. FL = In-lock flag; FL = 1: loop is phase-locked. The loop must be phase-locked during at least 8 periods of the internal

7.8125 kHz reference frequency before the FL flag is internally set to 1.

3. I2, I1 and I0 = digital information for I/O ports P2, P1 and P0 respectively.

4. A2, A1 and A0 = built-in 5-level A/D converter on I/O port P6. AFC information to the controller of the IF section is

available on pin 10 (see Table "Digital AFC status").

5. A = Acknowledge.

ELEGRAM EXAMPLES

(READ

MODE

)

Start - Adb - Ack - STB - Ack - STB - - Stop (no Ack from processor = End-of-data).

Start - Adb - Ack - STB - - Stop (no Ack from processor = End-of-data).

Where:

STB = Status byte.

BYTE

BITS

MSB

LSB

(5)

Address byte

MA1

MA0

Status byte

POR

(1)

(2)

(3)

(4)

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Video buffer

A video buffer is built into the video module to enable the
unit to drive a 75

load directly. In case it is required to

use the FI1216MF MK2 as a replacement for the FI1216 in
the same videocard, it is necessary to replace the 75

series resistor in the video card by a 0

series resistor. At

the same time the 22 k

series resistor in the tuning

supply must be removed.

C-bus load

The FI1216MF MK2 contains a series resistor (R = 100

)

in the SCL and SDA lines. Both lines also have a
capacitive load of typical 56 pF (see Fig.3).

Fig.3 I

C-bus load.

handbook, halfpage

MBH031

C1
56 pF

100

SCL

C3
56 pF

100

SDA

C2
56 pF

100

VCC

PLL IC

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

MECHANICAL DATA

Fig.4 Mechanical outline FI versions.

Dimensions in mm.

(1) Standard phono socket female 75

(2) Alternative IEC connection.

handbook, full pagewidth

4.445

21 22

23 24 25

0.64

12 13 14 15

84.5

89.2

2.6

1.1

3 (2

)

45.4

TH4

TH3

TH2

6.35

0.10

0.04

8.5

0.2

(1)

2.5

0.5

78.4

7.9

0.8

5.1

14.7

59.2

33.7

0.2

25.9

20.6

16.6

15.8

10.4

34.2

0.2

9.7 11.5

30.8

27.6

26.9

31.6

13.5 max

12.9 max

5.2

1.5 (2

)

(0.6)

1.5

)

2.6

34.7

28.55

38.5

MGB515 - 1

8.1

0.3

8.35

STANDARD PHONO CONNECTOR

(1)

14.4

0.2

IEC CONNECTOR

(2)

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

Aerial connections

Standard-phono socket female 75

or IEC (female).

Solderability

The solderability of pins and mounting tags when tested
initially and after 16 hours steam ageing in accordance
with

``IEC 68-2-20'', test Ta, method 1 (solder bath 235

for 2 s), results in a wetted area of 95%. No de-wetting will
occur when soldered at 260

C for 5 s.

Resistance to soldering heat

The product will not be damaged when tested in
accordance with

``IEC 68-2-20'', test Tb, method 1A

(solder bath 260

C for 10

1 s).

Mass

Approximately 50 g.

Robustness of pins

The pins will not be damaged when tested in accordance
with

``IEC 68-2-21'':

Test Ua1, tensile of 10 N in axial direction

Test Ua2, thrust of 4 N in axial direction.

Punching pattern of chassis PCB

Field rejects are often related to broken tag joints.
Therefore, the following punching pattern is recommended
(see Fig.5).

Fig.5 Punching pattern seen from solder side.

handbook, full pagewidth

59.2

14.7

4.445

2.1

1.1

34.7

2.3

3.4

78.4

0.9

unit

contour

MGB514 - 1

2.6

Dimensions in mm.

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

TV CHANNEL FREQUENCIES (MHz)

CCIR cable

Vision IF = 38.90 MHz; sound IF = 33.40 MHz.

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

47-54

48.25

53.75

54-61

55.25

60.75

61-68

62.25

67.75

S01

68-75

69.25

74.75

S02

75-82

76.25

81.75

S03

82-89

83.25

88.75

104-111

105.25

110.75

111-118

112.25

117.75

118-125

119.25

124.75

125-132

126.25

131.75

132-139

133.25

138.75

139-146

140.25

145.75

146-153

147.25

152.75

153-160

154.25

159.75

160-167

161.25

166.75

S10

167-174

168.25

173.75

174-181

175.25

180.75

181-188

182.25

187.75

188-195

189.25

194.75

195-202

196.25

201.75

202-209

203.25

208.75

E10

209-216

210.25

215.75

E11

216-223

217.25

222.75

E12

223-230

224.25

229.75

S11

230-237

231.25

236.75

S12

237-244

238.25

243.75

S13

244-251

245.25

250.75

S14

251-258

252.25

257.75

S15

258-265

259.25

264.75

S16

265-272

266.25

271.75

S17

272-279

273.25

278.75

S18

279-286

280.25

285.75

S19

286-293

287.25

292.75

S20

293-300

294.25

299.75

S21

302-310

303.25

308.75

S22

310-318

311.25

316.75

S23

318-326

319.25

324.75

S24

326-334

327.25

332.75

S25

334-342

335.25

340.75

S26

342-350

343.25

348.75

S27

350-358

351.25

356.75

S28

358-366

359.25

364.75

S29

366-374

367.25

372.75

S30

374-382

375.25

380.75

S31

382-390

383.25

388.75

S32

390-398

391.25

396.75

S33

398-406

399.25

404.75

S34

406-414

407.25

412.75

S35

414-422

415.25

420.75

S36

422-430

423.25

428.75

S37

430-438

431.25

436.75

S38

438-446

439.25

444.75

S39

446-454

447.25

452.75

S40

454-462

455.25

460.75

S41

462-470

463.25

468.75

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

CCIR B/G

Vision IF = 38.90 MHz; sound IF = 33.40 MHz.

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

47-54

48.25

53.75

54-61

55.25

60.75

61-68

62.25

67.75

174-181

175.25

180.75

181-188

182.25

187.75

188-195

189.25

194.75

195-202

196.25

201.75

202-209

203.25

208.75

209-216

210.25

215.75

216-223

217.25

222.75

223-230

224.25

229.75

470-478

471.25

476.75

478-486

479.25

484.75

486-494

487.25

492.75

494-502

495.25

500.75

502-510

503.25

508.75

510-518

511.25

516.75

518-526

519.25

524.75

526-534

527.25

532.75

534-542

535.25

540.75

542-550

543.25

548.75

550-558

551.25

556.75

558-566

559.25

564.75

566-574

567.25

572.75

574-582

575.25

580.75

582-590

583.25

588.75

590-598

591.25

596.75

598-606

599.25

604.75

606-614

607.25

612.75

614-622

615.25

620.75

622-630

623.25

628.75

630-638

631.25

636.75

638-646

639.25

644.75

646-654

647.25

652.75

654-662

655.25

660.75

662-670

663.25

668.75

670-678

671.25

676.75

678-686

679.25

684.75

686-694

687.25

692.75

694-702

695.25

700.75

702-710

703.25

708.75

710-718

711.25

716.75

718-726

719.25

724.75

726-734

727.25

732.75

734-742

735.25

740.75

742-750

743.25

748.75

750-758

751.25

756.75

758-766

759.25

764.75

766-774

767.25

772.75

774-782

775.25

780.75

782-790

783.25

788.75

790-798

791.25

796.75

798-806

799.25

804.75

806-814

807.25

812.75

814-822

815.25

820.75

822-830

823.25

828.75

830-838

831.25

836.75

838-846

839.25

844.75

846-854

847.25

852.75

854-862

855.25

860.75

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

France

Vision IF = 38.90 MHz; sound IF = 32.40 MHz.

CHANNEL

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

47.75

41.25

55.75

49.25

FC1

60.50

54.00

63.75

57.25

176.00

182.50

184.00

190.50

192.00

198.50

200.00

206.50

208.00

214.50

216.00

222.50

1996 Jul 09

Philips Components

Preliminary specification

Desktop video tuner
multi system CCIR L/L' and B/G

FI1216MF MK2

DEFINITIONS

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

PURCHASE OF PHILIPS I

C COMPONENTS

Data sheet status

Objective specification

This data sheet contains target or goal specifications for product development.

Preliminary specification

This data sheet contains preliminary data; supplementary data may be published later.

Product specification

This data sheet contains final product specifications.

Application information

Where application information is given, it is advisory and does not form part of the specification.

Purchase of Philips I

C components conveys a license under the Philips' I

C patent to use the

components in the I

C system provided the system conforms to the I

C specification defined by

Philips. This specification can be ordered using the code 9398 393 40011.

Philips Components a worldwide company

Argentina: IEROD, Av. Juramento, 1991-14.B, (1428) BUENOS AIRES,

Tel. (541) 786 7635, Fax. (541) 786 9367.

Australia: PHILIPS COMPONENTS PTY Ltd, 34 Waterloo Road,

NORTH RYDE NSW 2113, Tel. (02) 805 4455, Fax. (02) 805 4466.

Austria: PHILIPS COMPONENTS, Vertriebsgesellschaft m.b.H.,

Triester Strasse 64, A-1101 WIEN, P.O. Box 213,
Tel. (01) 601 01 12 12, Fax. (01) 60 101 12 10.

Belgium: PHILIPS NEDERLAND B.V., Philips Components &

Semiconductors, Postbus 90050, 5600 PB EINDHOVEN,
Netherlands, Tel. (31) 40 2783 749, Fax. (31) 40 2788 399.

Belarus: PHILIPS OFFICE BELARUS, Hotel Minsk, Volodarski Str. 6,

220050 MINSK, Tel. (5172) 200 915, Fax. (5172) 200 773.

Brazil: PHILIPS COMPONENTS, Rua do Rocio 220 - 5

floor,

04552-903 - SÃO PAULO - SP, Tel. (011) 821 2333, Fax. (011) 829 1849.

Canada: PHILIPS ELECTRONICS Ltd., Philips Components,

601 Milner Ave., SCARBOROUGH, Ontario, M1B 1M8,
Tel. (0416) 292 5161, Fax. (0416) 754 6248.

Chile: PHILIPS CHILENA S.A., Av. Santa Maria 0760, SANTIAGO,

Tel. (02) 77 38 16, Fax. (02) 735 35 94.

China: PHILIPS COMPANY, Philips Components MSO PRC,

6/F Building 2 No. 889, Yi Shan Road, SHANGHAI 200233,
Tel. (21) 485 0600, Fax. (21) 485 1015.

Colombia: IPRELENSO LTDA, Diagonal 59, No. 20-27,

P.O. Box 77621, SANTAFE DE BOGOTA,
Tel. (57) (1) 345 8713, Fax. (57) (1) 345 8712.

Denmark: PHILIPS COMPONENTS A/S, Prags Boulevard 80,

P.O Box 1919, 2300 COPENHAGEN S,
Tel. (32) 883 333, Fax. (31) 571 949.

Finland: PHILIPS COMPONENTS, Sinikalliontie 3,

FIN-02630 ESPOO, Tel. (9) 0-615 800, Fax. (9) 0-615 80920.

France: PHILIPS COMPOSANTS, 4 Rue du Port-aux-Vins, BP317,

92156 SURESNES, Cedex, Tel. (01) 4099 6161, Fax. (01) 4099 6427.

Germany: PHILIPS COMPONENTS UB der Philips G.m.b.H.,

P.O. Box 10 63 23, 20043 HAMBURG,
Tel. (040) 2489 1330, Fax. (040) 2489 1426.

Greece: PHILIPS HELLENIQUE S.A., Components Division,

No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01) 4894 339/(01) 4894 911, Fax. (01) 4815 180.

Hong Kong: PHILIPS HONG KONG, Components Division,

Unit 003-005, G/F, Hong Kong Ind. Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, KOWLOON,
Tel. (852) 2784 3000, Fax. (852) 2784 3003.

India: Philips INDIA Ltd., Components Dept.,

Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, BOMBAY 400 018,
Tel. (022) 4938 541, Fax. (022) 4938 722.

Indonesia: P.T. PHILIPS DEVELOPMENT CORPORATION,

Philips House, Jalan H.R. Rasuna Said Kav. 3-4, P.O. Box 4252,
JAKARTA 12950, Tel. (021) 520 1122, Fax. (021) 520 5189.

Ireland: PHILIPS ELECTRONICS (IRELAND) Ltd.,

Components Division, Newstead, Clonskeagh, DUBLIN 14,
Tel. (01) 76 40 203, Fax. (01) 76 40 210.

Israel: Rapac Electronics Ltd., 7 Kehilat Saloniki St. P.O. Box 18053,

TEL AVIV 61180, Tel. (03) 6450 444, Fax. (03) 6491 007.

Italy: PHILIPS COMPONENTS S.r.l., Piazza IV Novembre 3,

20124 MILANO, Tel. (02) 6752 2531, Fax. (02) 6752 2557.

Japan: PHILIPS JAPAN Ltd., Components Division,

Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. (03) 3740 5028, Fax. (03) 3740 0580.

Korea (Republic of): PHILIPS ELECTRONICS (KOREA) Ltd.,

Components Division, Philips House, 260-199 Itaewon-dong,
Yongsan-ku, SEOUL, Tel. (02) 709 1472, Fax. (02) 709 1479.

Malaysia: PHILIPS MALAYSIA SDN BERHAD, Components Division,

No. 76 Jalan Universiti, 46200 Petaling Jaya, KUALA LUMPUR,
Tel. (03) 757 5511, Fax. (03) 757 4880.
PHILIPS MALAYSIA SDN BERHAD, Components Division,
345 Jalan Gelugor, PULAU PINANG,
Tel. (04) 870 055, Fax. (04) 879 215.

Mexico: PHILIPS COMPONENTS, 5900 Gateway East,

Suite 200, EL PASO, TX 79905, U.S.A.,
Tel. (915) 772 4020, Fax. (915) 772 4332.

Netherlands: PHILIPS NEDERLAND B.V., Philips Components &

Semiconductors, Bldg. VB Postbus 90050, 5600 PB EINDHOVEN,
Tel. (040) 2783 749, Fax. (040) 2788 399.

New Zealand: PHILIPS NEW ZEALAND Ltd., Components Division,

2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09) 849 4160, Fax. (09) 849 7811.

Norway: NORSK A/S PHILIPS, Philips Components, Box 1,

Manglerud 0612, OSLO, Tel. (22) 74 8000, Fax. (22) 74 8341.

Pakistan: Philips Electrical Industries of Pakistan Ltd.,

Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,
KARACHI 75600, Tel. (021) 587 4641-49, Fax. (021) 577 035/587 4546.

Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc.,

106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. (02) 810 0161, Fax. (02) 817 3474.

Poland: PHILIPS POLAND Sp. z.o.o. Components Division, ul. Lutkiska 10,

04-123 WARSZAWA, Tel. (22) 612 2594, Fax. (22) 612 2327.

Portugal: PHILIPS PORTUGUESA, S.A.,

Rua dr. António Loureiro Borges 5, Arquiparque - Miraflores,
Apartado 300, 2795 LINDA-A-VELHA,
Tel. (01) 416 3160/416 3333, Fax. (01) 416 3174/416 3366.

Russia: PHILIPS RUSSIA, ul. Usatcheva 35A, 119048 MOSCOW,

Tel. (095) 926 5361, Fax. (095) 564 8323.

Singapore: PHILIPS SINGAPORE, Pte Ltd., Components Division,

Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65) 350 2000, Fax. (65) 355 1758.

South Africa: S.A. PHILIPS Pty Ltd., Components Division,

195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. (011) 470 5911, Fax. (011) 470 5494.

Spain: PHILIPS COMPONENTS, Balmes 22, 08007 BARCELONA,

Tel. (93) 301 63 12, Fax. (93) 301 42 43.

Sweden: PHILIPS COMPONENTS AB, Kottbygatan 7, Akalla.

Postal address: S-164 85 STOCKHOLM,
Tel. (+46) 8 632 2000, Fax. (+46) 8 632 2745.

Switzerland: PHILIPS COMPONENTS AG, Allmendstrasse 140, CH-8027

ZÜRICH, Tel. (01) 488 22 11, Fax. (01) 481 77 30.

Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West Road,

Sec. 1. Taipei, Taiwan ROC, P.O. Box 22978, TAIPEI 100,
Tel. (02) 388 7666, Fax. (02) 382 4382.

Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,

209/2 Sanpavuth-Bangna Road Prakanong, Bangkok 10260, THAILAND,
Tel. (66) 2 745 4090, Fax. (66) 2 398 0793.

Turkey: Türk Philips Ticaret A.S., Components Department,

Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. (0212) 279 2770, Fax. (0212) 282 6707.

Ukraine: PHILIPS UKRAINE Ltd., 2A Akademika Koroleva str.,

252148 KIEV, Tel. (044) 476 0297, Fax. (044) 476 6991.

United Kingdom: PHILIPS COMPONENTS Ltd., The Mullard Building,

Dorking Business Park, DORKING, Surrey, RH4 1HJ,
Tel. (01306) 512 000, Fax: (01306) 512 345.

United States: PHILIPS COMPONENTS, Division Headquarters,

1440 Indiantown Road, JUPITER, FL 33458,
Tel. (561) 745 3300, Fax. (561) 745 3600.
For literature: (800) 447 3762.
PHILIPS DISPLAY COMPONENTS COMPANY,
1600 Huron Parkway, ANN ARBOR, Michigan 48105-2590,
Tel. (313) 996 9400, Fax. (313) 761 2776.

Uruguay: PHILIPS COMPONENTS, Coronel Mora 433,

MONTEVIDEO, Tel. (02) 704 044, Fax. (02) 920 601.

For all other countries apply to: Philips Components,
Marketing Communications, P.O. Box 218, 5600 MD EINDHOVEN,
The Netherlands, Fax. +31-40-2724 547.

COD06

All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or
contract, is believed to be accurate and reliable and may be changed without notice.
No liability will be accepted by the publisher for any consequence of its use.
Publication thereof does not convey nor imply any license under patent- or other
industrial or intellectual property rights.

Printed in The Netherlands

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: FI1216MF

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: FI1216MF