Äîêóìåíòàöèÿ è îïèñàíèÿ www.docs.chipfind.ru

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

FEATURES

System CCIR B/G

True 5 V device (low power dissipation)

Full frequency range from channel 2 (48.25 MHz) to
channel 69 (855.25 MHz)

PLL controlled tuning

True-synchronous vision IF demodulator (PLL)

Demodulated video output, AF sound output, second
sound IF output

C-bus control of tuning, address selection, AFC status

information

Complies with European regulations on radiation, signal
handling and immunity

("CENELEC 55020, 55013'' and

``Amtsblatt 15/92")

Small horizontally mounted metal housing.

DESCRIPTION

The FI1200MK2 family consists of the following types
FI1216MK2, FI1246MK2, FI1256MK2. They are designed
to meet a wide range of RF applications in the PC
Multi-Media environment.

The FI1216MK2 types are available with a single 75

input for TV reception. The input connector is available in
either standard phono (female socket) or IEC (female
socket).

The tuning and bandswitching are performed through the
built-in digitally controlled I

C-bus. All front-ends meet the

input immunity and radiation of CENELEC.

The FI1216MK2 consists of a tuner section and an IF
section, which are all designed on a single PCB. The
front-end is assembled in a metal housing made of a
rectangular tin plated steel frame with front and rear covers
which have soldered contacts to the frame. A single phono
or IEC aerial socket is mounted on one side of the frame.
All other connections are made via pins at the bottom.

The tuner section is equipped with 3 tuned RF MOSFET
input stages, with a 3-band mixer-oscillator IC, containing
the oscillators, mixers and IF amplifier. Tuning and band
switching in the tuner section are done with a digital
programmable PLL tuning system. This enables tuning
with step-size programmable between 31.25,
50.0 or 62.5 kHz. A DC-DC converter is built around the
PLL synthesizer IC to provide the tuning voltage, thus
making the FI1216MK2 front-end a true 5 V device.

The IF section uses a true-synchronous vision IF
demodulator (PLL) with an intercarrier SAW filter in front
of it.

The analog AFC voltage is fed to the 5-level A/D converter
in the PLL tuning IC, so that the AFC status can be read
via the I

C-bus.

ORDERING INFORMATION

MARKING

The following items of information are printed on a sticker
that is on the top cover of the tuner:

Type number

Code number

Origin letter of factory

Change code

Year and week code.

INTERMEDIATE FREQUENCIES

Note

1. The oscillator frequency is above the input signal

frequency.

CHANNEL COVERAGE

TYPE

DESCRIPTION

CATALOGUE

NUMBERS

FI1216MK2/HM/PH

standard phono 3139 147 13291

FI1216MK2/HM/IEC IEC

3139 147 13301

SYSTEM

FREQUENCY

(1)

(MHz)

PAL B/G

Picture carrier

38.90

Colour

34.47

Sound 1

33.40

Sound 2

33.16

NICAM

33.05

BAND

CHANNELS

Low band

48.25 to 170.00 MHz

Mid band

170.00 to 450.00 MHz

High band

450.00 to 855.25 MHz

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

LIMITING VALUES

Limiting values under operational conditions

The tuner can be guaranteed to function properly under the following conditions.

Notes

1. Sinusoidal ripple voltage superimposed on the 5 V supply voltage in the frequency range of 20 Hz to 500 kHz.

Criteria for TV interference >57 dB.

2. For detailed information about the address decoding, refer to Chapter "Application information".

SYMBOL

PARAMETER

PIN

MIN.

TYP.

MAX.

UNIT

supply voltage

4.75

5.00

5.25

S(ripple)

peak-to-peak ripple voltage susceptibility
(at 5 V

5%); note 1

20 Hz to 100 kHz

>100 kHz to 500 kHz

supply current

120

SCL

SCL bus input voltage

0.3

+5.25

SDA

SDA bus input voltage

0.3

+5.25

SDA

SDA bus current (open collector)

address select voltage; note 2

+5.25

IF sound output load impedance:

0.5

CVBS

Composite Video Baseband Signal load
impedance:

load time constant

100

IF supply voltage

4.75

5.0

5.25

IF(ripple)

peak-to-peak ripple voltage susceptibility
(at 5 V

5%); note 1

20 Hz to 100 kHz

>100 kHz to 500 kHz

IF supply current

100

AF sound output load impedance:

1.0

0.6

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

Environmental conditions

OVERALL PERFORMANCE

Conditional data

Unless otherwise specified, all electrical values for Chapter "Overall performance" apply at the following conditions.

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

Non-operational conditions

amb

ambient temperature

+85

relative humidity

100

bump acceleration

25 g

245

m/s

shock acceleration

50 g

490

m/s

vibration amplitude

10 to 55 Hz

0.35

Operational conditions

amb

ambient temperature

+60

relative humidity

SYMBOL

PARAMETER

VALUE

UNIT

amb

ambient temperature

relative humidity

supply voltage (tuner and IF section)

0.125

CVBS

video output load impedance (DC)

>75

IF sound output load impedance (DC)

>500

pre-heating time (+5 V at pin 24)

minute

S(AE)

aerial source impedance (unbalanced)

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

Definitions of test signals (see Fig.2)

Aerial input characteristics

TEST SIGNAL

FREQ.

(MHz)

AMPLITUDE

MODULATION

VIDEO

AUDIO

A0: unmodulated vision
carrier

480.25

60 dB

A1: CCIR B/G standard signal
with video modulation

480.25

60 dB

(top sync)

100% (rest carrier 10%)
2T pulse and bar

B1: unmodulated sound
carrier B/G system

485.75

13 dB w.r.t.

A0 to A1

B2: FM modulated sound
carrier B/G system

485.75

13 dB w.r.t.

A0 to A1

1 kHz; modulation frequency
deviation

27 kHz;

s pre-emphasis

B3: unmodulated sound
carrier B/G system

478.75

13 dB w.r.t.

A0 to A1

SYMBOL

PARAMETER

CONDITIONS

MIN.

MAX.

UNIT

VSWR

reflection coefficient

referred to 75

impedance (worst case on or between

picture and sound carrier at maximum gain)

PSM

surge protection voltage

ant

antenna connection
disturbance voltage

<1.75 GHz

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

General characteristics

Note

1. All the pins of the desktop video tuner are protected against electrostatic discharge (ESD) up to 2 kV. The product is

classified in category B

(``MIL-STD-883C").

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

frequency range:

low band

48.25

168.25

MHz

mid band

175.25

447.25

MHz

high band

455.25

855.25

MHz

margin:

for low band

1.5

MHz

for mid/high band

MHz

image rejection (nominal gain to 10 dB
gain reduction):

low band

mid band

<300 MHz

mid band

>300 MHz

high band

IF rejection (picture)

IF susceptibility:

E2 to E12

E21 to E69

sound-chrominance moiré rejection:

off-air

up to 40 dB gain control

UHF

up to 30 dB minimum
gain control

cross modulation:

in-channel

in-band

low band (n

mid band (n

high band (n

out of band

100

breakthrough susceptibility:

E2 to E12; E21 to E69

osc

oscillator voltage at all pins

oscillators lock-in time

charge pump set logic
HIGH

150

the video signal-to-sound interference
ratio with the tuner exposed to sound
signals in the audio frequency range
100 Hz to 10 kHz and sound pressure
levels up to 105 dB (20

Pa)

ESD

electrostatic discharge (ESD)
on all pins

note 1

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

Video and audio characteristics (see Fig.2)

Digital AFC status

PARAMETER

TEST SIGNAL

TEST

POINT

MIN.

TYP.

MAX.

UNIT

CVBS characteristics:

video amplitude signal at pin 23

A1 (peak-to-peak value)

BU4

0.7

1.1

DC level sync pulse at pin 23

BU4

0.35

Video amplitude drop with respect to modulation
0.1 MHz at T

amb

= 45

at 1 MHz

BU4

1.0

+1.0

at 2 MHz

BU4

1.5

+1.5

at 3 MHz

BU4

2.5

+1.5

at 4 MHz

BU4

3.0

+2.0

at 4.43 MHz

BU4

4.0

+2.0

Sound carrier rejection

A1 (1 MHz) + B1

BU4

Residual 40.4 MHz signal in video channel:
level of 1.5 MHz

A1 + B3

BU4

Residual 77.8 MHz signal in video channel

BU4

Second IF sound output level at level of 5.5 MHz

A1 + B1

BU5

Test on 2T pulse at T

amb

= 45

2T pulse/bar response

BU4

2.5

+2.5

2T pulse response

BU4

+3.0

CVBS S/N (unweighted)

A1 + B1

BU4

Gain limited sensitivity at 1 dB reduction
of video output

BU4

Audio characteristics:

AF output level measured via LP 20 kHz filter,
RMS detector, 50

s de-emphasis

A1 + B2

BU6

0.25

0.35

0.50

THD (Total Harmonic Distortion) measured via
LP 20 kHz filter, RMS detector, 50

de-emphasis

A1 + B2

BU6

0.5

S/N measured via CCIR filter, peak
CCIR detector, 50

s de-emphasis

A1 (6 kHz sine wave,
black-to-white) + B1

BU6

AF 3 dB response measured via LP 20 kHz filter,
RMS detector, de-emphasis off

A1 (black) + B1

BU6

kHz

AM suppression ratio

A1 + B2

BU6

PARAMETER

CONDITIONS

FREQUENCY

(kHz)

DIGITAL

READ-OUT

ADC word at I

C-bus during read operation

input voltage at pin 10: 0.0 to 0.15V

125

input voltage at pin 10: 0.15 to 0.30V

62.5

input voltage at pin 10: 0.30 to 0.45V

input voltage at pin 10: 0.45 to 0.60V

+62.5

input voltage at pin 10: 0.60 to 1.00V

+125

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

APPLICATION INFORMATION

A detailed description of the I

C-bus specification, with applications, is given in brochure

``The I

C-bus and how to

use it''. This brochure may be ordered using the code number 9398 393 40011.

WRITE mode

Note

1. A = Acknowledge.

DDRESS SELECTION

= +5 V (PLL supply voltage).

ROGRAMMABLE DIVIDER SETTINGS

(

BYTES

AND

Divider ratio:

N = 16

× {

RF(pc)

+ f

IF(pc)

}, where (pc) is picture carrier and f

and f

are expressed in MHz

osc

(MHz).

N = (8192

n13) + (4096

n12) + (2048

n11) + (1024

n10) + (512

n9) + (256

n8) + (128

n7) + (64

n6) +

(32

n5) + (16

n4) + (8

n3) + (4

n2) + (2

n1) + n0

ONTROL BYTE

Charge pump settings:

CP = 1, for fast tuning

CP = 0, for moderate speed tuning with slightly better residual oscillator FM.

Test mode settings:

T2 = T1 = 0; T0 = 1, for normal operation.

PLL disabling:

OS = 0, for normal operation

OS = 1, for switching the charge pump to the high impedance state.

BYTE

BITS

MSB

LSB

(1)

Address byte

MA1

MA0

Program divider byte 1

n14

n13

n12

n11

n10

Program divider byte 2

Control information byte 1

RSA

RSB

Control information byte 2

MA1

MA0

ADDRESS

VOLTAGE AT PIN 15

0.0V

to 0.1V

0.2V

to 0.3V

0.4V

to 0.6V

0.9V

to 1.0V

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

Ratio select bits

ORTS BYTE

Band switching

Notes

1. X = don't care; P0 to P7 are output ports on the PLL device.

2. P3 is a system switch output for customer applications.

ELEGRAM EXAMPLES

(WRITE

MODE

)

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop.

Start - Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Stop.

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Where:

Start = start condition

Adb = address byte

Ack = acknowledge

Db1 = divider byte 1

Db2 = divider byte 2

Cb = control byte

Pb = ports byte

Stop = stop condition.

Remark: for channel selection involving band switching, and to ensure smooth tuning to the desired channel without
causing unnecessary charge pump action, it is recommended to consider the difference between wanted channel
frequency (f

) and the current channel frequency (f

If f

> f

, use telegram as:

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop.

If f

< f

, use telegram as:

Start - Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Unnecessary charge pump action will result in very low tuning voltage (V

0 V) which may drive the oscillator to extreme

conditions.

RSA

RSB

STEP SIZE

50 kHz

31.25 kHz (for slow picture search)

62.5 kHz (for normal picture search)

BAND

BIT

(1)

(2)

Low band

Mid band

High band

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

READ mode

The in-lock can be read by setting the R/W bit to 1.

Notes

1. POR = Power On Reset. POR is internally set to 1 in case V

drops below 3 V. The POR bit is reset when an end of

data is detected by the PLL IC.

2. FL = In-lock flag; FL = 1: loop is phase-locked. The loop must be phase-locked during at least 8 periods of the internal

7.8125 kHz reference frequency before the FL flag is internally set to 1.

3. I2, I1 and I0 = digital information for I/O ports P2, P1 and P0 respectively.

4. A2, A1 and A0 = built-in 5-level A/D converter on I/O port P6. AFC information to the controller of the IF section is

available on pin 10 (see Table "Digital AFC status").

5. A = Acknowledge.

ELEGRAM EXAMPLES

(READ

MODE

)

Start - Adb - Ack - STB - Ack - STB - - Stop (no Ack from processor = End-of-data).

Start - Adb - Ack - STB - - Stop (no Ack from processor = End-of-data).

Where:

STB = Status byte.

BYTE

BITS

MSB

LSB

(5)

Address byte

MA1

MA0

Status byte

POR

(1)

(2)

(3)

(4)

Video buffer

A video buffer is built into the video module to enable the
unit to drive a 75

load directly. In case it is required to

use the FI1216MK2 as a replacement for the FI1216 in the
same videocard, it is necessary to replace the 75

series

resistor in the video card by a 0

series resistor. At the

same time the 22 k

series resistor in the tuning supply

must be removed.

C-bus load

The FI1216MK2 contains a series resistor (R = 100

) in

the SCL and SDA lines. Both lines also have a capacitive
load of typical 56 pF (see Fig.3).

Fig.3 I

C-bus load.

handbook, halfpage

MBH031

C1
56 pF

100

SCL

C3
56 pF

100

SDA

C2
56 pF

100

VCC

PLL IC

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

Aerial connections

Standard-phono socket female 75

or IEC (female).

Solderability

The solderability of pins and mounting tags when tested
initially and after 16 hours steam ageing in accordance
with

``IEC 68-2-20'', test Ta, method 1 (solder bath 235

for 2 s), results in a wetted area of 95%. No de-wetting will
occur when soldered at 260

C for 5 s.

Resistance to soldering heat

The product will not be damaged when tested in
accordance with

``IEC 68-2-20'', test Tb, method 1A

(solder bath 260

C for 10

1 s).

Mass

Approximately 50 g.

Robustness of pins

The pins will not be damaged when tested in accordance
with

``IEC 68-2-21'':

Test Ua1, tensile of 10 N in axial direction

Test Ua2, thrust of 4 N in axial direction.

Punching pattern of chassis PCB

Field rejects are often related to broken tag joints.
Therefore, the following punching pattern is recommended
(see Fig.5).

Fig.5 Punching pattern seen from solder side.

handbook, full pagewidth

59.2

14.7

4.445

2.1

1.1

34.7

2.3

3.4

78.4

0.9

unit

contour

MGB514 - 1

2.6

Dimensions in mm.

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

TV CHANNEL FREQUENCIES (MHz)

CCIR cable

Vision IF = 38.90 MHz; sound IF = 33.40 MHz.

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

47-54

48.25

53.75

54-61

55.25

60.75

61-68

62.25

67.75

S01

68-75

69.25

74.75

S02

75-82

76.25

81.75

S03

82-89

83.25

88.75

104-111

105.25

110.75

111-118

112.25

117.75

118-125

119.25

124.75

125-132

126.25

131.75

132-139

133.25

138.75

139-146

140.25

145.75

146-153

147.25

152.75

153-160

154.25

159.75

160-167

161.25

166.75

S10

167-174

168.25

173.75

174-181

175.25

180.75

181-188

182.25

187.75

188-195

189.25

194.75

195-202

196.25

201.75

202-209

203.25

208.75

E10

209-216

210.25

215.75

E11

216-223

217.25

222.75

E12

223-230

224.25

229.75

S11

230-237

231.25

236.75

S12

237-244

238.25

243.75

S13

244-251

245.25

250.75

S14

251-258

252.25

257.75

S15

258-265

259.25

264.75

S16

265-272

266.25

271.75

S17

272-279

273.25

278.75

S18

279-286

280.25

285.75

S19

286-293

287.25

292.75

S20

293-300

294.25

299.75

S21

302-310

303.25

308.75

S22

310-318

311.25

316.75

S23

318-326

319.25

324.75

S24

326-334

327.25

332.75

S25

334-342

335.25

340.75

S26

342-350

343.25

348.75

S27

350-358

351.25

356.75

S28

358-366

359.25

364.75

S29

366-374

367.25

372.75

S30

374-382

375.25

380.75

S31

382-390

383.25

388.75

S32

390-398

391.25

396.75

S33

398-406

399.25

404.75

S34

406-414

407.25

412.75

S35

414-422

415.25

420.75

S36

422-430

423.25

428.75

S37

430-438

431.25

436.75

S38

438-446

439.25

444.75

S39

446-454

447.25

452.75

S40

454-462

455.25

460.75

S41

462-470

463.25

468.75

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

CCIR B/G

Vision IF = 38.90 MHz; sound IF = 33.40 MHz.

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

47-54

48.25

53.75

54-61

55.25

60.75

61-68

62.25

67.75

174-181

175.25

180.75

181-188

182.25

187.75

188-195

189.25

194.75

195-202

196.25

201.75

202-209

203.25

208.75

209-216

210.25

215.75

216-223

217.25

222.75

223-230

224.25

229.75

470-478

471.25

476.75

478-486

479.25

484.75

486-494

487.25

492.75

494-502

495.25

500.75

502-510

503.25

508.75

510-518

511.25

516.75

518-526

519.25

524.75

526-534

527.25

532.75

534-542

535.25

540.75

542-550

543.25

548.75

550-558

551.25

556.75

558-566

559.25

564.75

566-574

567.25

572.75

574-582

575.25

580.75

582-590

583.25

588.75

590-598

591.25

596.75

598-606

599.25

604.75

606-614

607.25

612.75

614-622

615.25

620.75

622-630

623.25

628.75

630-638

631.25

636.75

638-646

639.25

644.75

646-654

647.25

652.75

654-662

655.25

660.75

662-670

663.25

668.75

670-678

671.25

676.75

678-686

679.25

684.75

686-694

687.25

692.75

694-702

695.25

700.75

702-710

703.25

708.75

710-718

711.25

716.75

718-726

719.25

724.75

726-734

727.25

732.75

734-742

735.25

740.75

742-750

743.25

748.75

750-758

751.25

756.75

758-766

759.25

764.75

766-774

767.25

772.75

774-782

775.25

780.75

782-790

783.25

788.75

790-798

791.25

796.75

798-806

799.25

804.75

806-814

807.25

812.75

814-822

815.25

820.75

822-830

823.25

828.75

830-838

831.25

836.75

838-846

839.25

844.75

846-854

847.25

852.75

854-862

855.25

860.75

CHANNEL

FREQ.

RANGE

PICTURE

CARRIER

FREQUENCY

SOUND

CARRIER

FREQUENCY

1997 Mar 13

Philips Components

Preliminary specification

Desktop video tuner
system CCIR B/G

FI1216MK2

Italy

Vision IF = 38.90 MHz; sound IF = 33.40 MHz.

DEFINITIONS

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

PURCHASE OF PHILIPS I

C COMPONENTS

CHANNEL

PICTURE CARRIER FREQUENCY

SOUND CARRIER FREQUENCY

53.75

59.25

62.25

67.75

82.25

87.75

175.25

180.75

183.75

189.25

197.25

192.75

201.25

206.75

210.25

215.75

217.25

222.75

224.25

229.75

Data sheet status

Objective specification

This data sheet contains target or goal specifications for product development.

Preliminary specification

This data sheet contains preliminary data; supplementary data may be published later.

Product specification

This data sheet contains final product specifications.

Application information

Where application information is given, it is advisory and does not form part of the specification.

Purchase of Philips I

C components conveys a license under the Philips' I

C patent to use the

components in the I

C system provided the system conforms to the I

C specification defined by

Philips. This specification can be ordered using the code 9398 393 40011.

Philips Components a worldwide company

Argentina: Ierod, BUENOS AIRES,

Tel. (01) 786 7635, Fax. (01) 786 9397.

Australia: Philips Components Pty Ltd, NORTH RYDE,

Tel. (02) 9805 4455, Fax. (02) 9805 4466.

Austria: Österreichische Philips Industrie GmbH, WIEN,

Tel. (01) 601 01 12 41, Fax. (01) 60 101 12 11.

Belarus: Philips Office Belarus, MINSK,

Tel. (5172) 200 915, Fax. (5172) 200 773.

Benelux: Philips Nederland B.V., EINDHOVEN, NL.,

Tel. (+31 40) 2783 749, Fax. (+31 40) 2788 399.

Brazil: Philips Components, SÃO PAULO,

Tel. (011) 821 2333, Fax. (011) 829 1849.

Canada: Philips Electronics Ltd., SCARBOROUGH,

Tel. (0416) 292 5161, Fax. (0416) 754 6248.

China: Philips Company, SHANGHAI,

Tel. (021) 6485 0600, Fax. (021) 6485 5615.

Colombia: Iprelenso Ltda, SANTAFE DE BOGOTA,

Tel. (01) 345 8713, Fax. (01) 345 8712.

Denmark: Philips Components A/S, COPENHAGEN S,

Tel. (32) 883 333, Fax. (31) 571 949.

Finland: Philips Components, ESPOO,

Tel. 9 (0)-615 800, Fax. 9 (0)-615 80510.

France: Philips Composants, SURESNES,

Tel. (01) 4099 6161, Fax. (01) 4099 6427.

Germany: Philips Components GmbH, HAMBURG,

Tel. (040) 2489-0, Fax. (040) 2489 1400.

Greece: Philips Hellas S.A., TAVROS,

Tel. (01) 4894 339/(01) 4894 239, Fax. (01) 4814 240.

Hong Kong: Philips Hong Kong, KOWLOON,

Tel. 2784 3000, Fax. 2784 3003.

India: Philips India Ltd., BOMBAY,

Tel. (022) 4938 541, Fax. (022) 4938 722.

Indonesia: P.T. Philips Development Corp., JAKARTA,

Tel. (021) 520 1122, Fax. (021) 520 5189.

Ireland: Philips Electronics (Ireland) Ltd., DUBLIN,

Tel. (01) 76 40 203, Fax. (01) 76 40 210.

Israel: Rapac Electronics Ltd., TEL AVIV,

Tel. (03) 6450 444, Fax. (03) 6491 007.

Italy: Philips Components S.r.l., MILANO,

Tel. (02) 6752 2531, Fax. (02) 6752 2557.

Japan: Philips Japan Ltd., TOKYO,

Tel. (03) 3740 5028, Fax. (03) 3740 0580.

Korea (Republic of): Philips Electronics (Korea) Ltd., SEOUL,

Tel. (02) 709 -1472, Fax. (02) 709 1480.

Malaysia: Philips Malaysia SDN Berhad

Components Division, PULAU PINANG,
Tel. (04) 657 0055, Fax. (04) 656 5951.

Mexico: Philips Components, EL PASO, U.S.A.,

Tel. (915) 772 4020, Fax. (915) 772 4332.

New Zealand: Philips New Zealand Ltd., AUCKLAND,

Tel. (09) 849 4160, Fax. (09) 849 7811.

Norway: Norsk A/S Philips, OSLO,

Tel. (22) 74 8000, Fax. (22) 74 8341.

Pakistan: Philips Electrical Industries of Pakistan Ltd., KARACHI,

Tel. (021) 587 4641-49, Fax. (021) 577 035/587 4546.

Philippines: Philips Semiconductors Philippines Inc.,

METRO MANILA, Tel. (02) 816 6380, Fax. (02) 817 3474.

Poland: Philips Poland Sp. z.o.o., WARSZAWA,

Tel. (022) 612 2594, Fax. (022) 612 2327.

Portugal: Philips Portuguesa S.A.,

Philips Components: LINDA-A-VELHA,
Tel. (01) 416 3160/416 3333, Fax. (01) 416 3174/416 3366.

Russia: Philips Russia, MOSCOW,

Tel. (095) 247 9124, Fax. (095) 247 9132.

Singapore: Philips Singapore Pte Ltd., SINGAPORE,

Tel. 350 2000, Fax. 355 1758.

South Africa: S.A. Philips Pty Ltd., JOHANNESBURG,

Tel. (011) 470 5911, Fax. (011) 470 5494.

Spain: Philips Components, BARCELONA,

Tel. (93) 301 63 12, Fax. (93) 301 42 43.

Sweden: Philips Components AB, STOCKHOLM,

Tel. (+46) 8 632 2000, Fax. (+46) 8 632 2745.

Switzerland: Philips Components AG, ZÜRICH,

Tel. (01) 488 22 11, Fax. (01) 481 77 30.

Taiwan: Philips Taiwan Ltd., TAIPEI,

Tel. (02) 388 7666, Fax. (02) 382 4382.

Thailand: Philips Electronics (Thailand) Ltd., BANGKOK,

Tel. (02) 745 4090, Fax. (02) 398 0793.

Turkey: Türk Philips Ticaret A.S., GÜLTEPE/ISTANBUL,

Tel. (0212) 279 2770, Fax. (0212) 282 6707.

Ukraine: Philips Ukraine Ltd., KIEV,

Tel. (044) 268 7327, Fax. (044) 268 6323.

United Kingdom: Philips Components Ltd., DORKING,

Tel. (01306) 512 000, Fax. (01306) 512 345.

United States:

· Philips Components, JUPITER, FL,

Tel. (561) 745 3300, Fax. (561) 745 3600.

· For literature: (800) 447 3762.

· Display and Wire Wound Components, ANN ARBOR, MI,

Tel. (313) 996 9400, Fax. (313) 761 2776.

· Magnetic Products, SAUGERTIES, NY,

Tel. (914) 246 2811, Fax. (914) 246 0487.

Uruguay: Philips Components, MONTEVIDEO,

Tel. (02) 704 044, Fax. (02) 920 601.

For all other countries apply to: Philips Components,
Marketing Communications, P.O. Box 218, 5600 MD EINDHOVEN,
The Netherlands, Fax. +31-40-2724 547.

COD11

All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or
contract, is believed to be accurate and reliable and may be changed without notice.
No liability will be accepted by the publisher for any consequence of its use. Publication
thereof does not convey nor imply any license under patent- or other industrial or
intellectual property rights.

Printed in The Netherlands

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: FI1216MK2

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: FI1216MK2