Äîêóìåíòàöèÿ è îïèñàíèÿ www.docs.chipfind.ru

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

FEATURES

System I and FM radio broadcast

True 5 V device (low power dissipation)

Full TV frequency range from channel A (45.75 MHz) to
channel 69 (855.25 MHz)

FM radio band coverage from 87.50 to 108.00 MHz

PLL controlled tuning

Programmable PLL step size (31.25, 50 or 62.5 kHz)

True-synchronous vision IF demodulator (PLL)

Ultra-linear FM PLL demodulator for FM radio broadcast

Demodulated video output, AF sound output, second
sound IF output

C-bus control of tuning, address selection, AFC status

information

Complies with European regulations on radiation, signal
handling and immunity

"CENELEC 55020, 55013''

Small horizontally mounted metal housing.

DESCRIPTION

The FM1246 front-end is designed to receive both TV and
FM stereo signals in the PC Multimedia environment. The
units are available with separate 75

inputs for TV and

FM broadcast reception. The input connectors available
are either standard phono or IEC type (female for TV, male
for FM radio). The tuning, bandswitching and antenna
selection are made through the I

C-bus.

The front-end covers the TV bands from 45.75 MHz to
855.25 MHz. The FM band covers the standard
87.50 MHz to 108.00 MHz. An RDS decoder can be
connected to the AF-MPX output. The FM1246 meets the
input immunity and radiation requirements of CENELEC.

The FM1246 consists of a TV tuner, an FM radio tuner and
an IF section, all on a single PCB. The front-end is
assembled in a metal housing made of a rectangular
tin-plated steel frame, with front and rear covers, which
have soldered contacts to the frame. The two phono or
IEC antenna connectors (female for TV, male for FM
radio) are mounted on one side of the frame for the TV/FM
signal inputs. All other connections are made via pins at
the bottom.

The TV IF section uses an intercarrier SAW filter, followed
by a true-synchronous vision IF demodulator (PLL) IC. The
analog AFC voltage is fed to the 5-level A/D converter in
the PLL tuning IC, so that the AFC status can be read via
the I

C-bus.

In the FM radio mode, the level detector and AFT functions
are provide for the auto-search routines. The level detector
and AFT status can be read from the A/D bits in the
status-byte. The mute function is also provided to
suppress the audio output signal, if required.

The tuner AGC for both TV and FM radio operation, is
generated with a novel AGC detector which measures the
IF signal level directly at the tuner IF output pins. As
opposed to the conventional AGC detector, this new circuit
allows a higher take-over level and offers superior
immunity against tuner overload.

The demodulation of the TV sound and FM radio IF
(10.70 MHz) is done with a PLL demodulation circuit
contained in the IF IC. In the FM radio mode, the
multiplexed AF signal is then channelled to a stereo
decoder IC which extracts the left/right analog signals.
The multiplexed audio signal is also available at pin 25 to
support RDS implementations. The 2

IF TV sound output

is provided to connect external (analog 2 carrier or digital)
stereo processing.

ORDERING INFORMATION

MARKING

The following items of information are printed on a sticker
that is on the top cover of the tuner:

Type number

Code number

Origin letter of factory

Change code

Year and week code.

TYPE

DESCRIPTION

CATALOGUE

NUMBERS

FM1246/HM/PH

standard phono

3139 147 13901

FM1246/HM/I

IEC connector

3139 147 13911

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

LIMITING VALUES

Limiting values under operational conditions

The tuner can be guaranteed to function properly under the following conditions.

Notes

1. Sinusoidal ripple voltage superimposed on the 5 V supply voltage in the frequency range of 20 Hz to 500 kHz.

Criteria for TV interference >57 dB.

2. For detailed information about the address decoding, refer to Chapter "Application information".

SYMBOL

PARAMETER

PIN

MIN.

TYP.

MAX.

UNIT

supply voltage

4.75

5.00

5.25

S(ripple)

peak-to-peak ripple voltage susceptibility
(at 5 V

5%); note 1

20 Hz to 100 kHz

>100 kHz to 500 kHz

S(tuner)

supply current

120

SCL

SCL bus input voltage

0.3

+5.25

SDA

SDA bus input voltage

0.3

+5.25

SDA

SDA bus current (open collector)

address select voltage; note 2

+5.25

AFright(FM)

FM right channel DC voltage

1.0

AFright(FM)

FM right channel load impedance parallel connected:

resistive value

capacitive value

AFleft(FM)

FM left channel DC voltage

1.0

AFleft(FM)

FM left channel load impedance:

resistive value

capacitive value

IF sound output load impedance

0.5

CVBS

Composite Video Baseband Signal load impedance

CVBS load time constant

100

S(IF)

IF supply voltage

4.75

5.0

5.25

S(IF)

IF supply current

150

AF sound output load impedance parallel connected:

resistive value

5.0

capacitive value

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

Environmental conditions

OVERALL PERFORMANCE

Conditional data

Unless otherwise specified, all electrical values for Chapter "Overall performance" apply at the following conditions.

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

Non-operational conditions

amb

ambient temperature

+85

relative humidity

100

bump acceleration

25 g

245

m/s

shock acceleration

50 g

490

m/s

vibration amplitude

10 to 55 Hz

0.35

Operational conditions

amb

ambient temperature

+60

relative humidity

SYMBOL

PARAMETER

VALUE

UNIT

amb

ambient temperature

relative humidity

supply voltage (tuner and IF section)

0.125

CVBS

video output load impedance (DC)

IF sound output load impedance (DC)

0.5

AF sound output load impedance

100

pre-heating time (+5 V at pin 24)

minutes

S(AE)

aerial source impedance (asymmetrical)

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

Definitions of test signals (see Fig.2)

Aerial input characteristics

TEST SIGNAL

FREQ.

(MHz)

AMPLITUDE

MODULATION

VIDEO

AUDIO

A0: unmodulated vision
carrier

480.25

60 dB

A1: CCIR I standard signal
with video modulation

480.25

60 dB

(top sync)

100% (rest carrier 10%)
2T pulse and bar

B1: unmodulated sound
carrier I system

486.25

7 dB w.r.t. A1

B2: FM modulated sound
carrier I system

486.25

7 dB w.r.t. A1

1 kHz; modulation frequency
deviation

27 kHz;

s pre-emphasis

B3: unmodulated sound
carrier I system

478.25

15 dB w.r.t. A1

C1: FM modulated sound
carrier

87.5

60 dB

1 kHz; modulation frequency
deviation

75 kHz;

10% pilot carrier (L = R)

C2: FM modulated sound
carrier

98.0

60 dB

1 kHz; modulation frequency
deviation

75 kHz;

10% pilot carrier (L = R)

C3: FM modulated sound
carrier

108.0

60 dB

1 kHz; modulation frequency
deviation

75 kHz;

10% pilot carrier (L = R)

C4: FM modulated sound
carrier

98.0

60 dB

1 kHz; modulation frequency
deviation

22.5 kHz

C5: unmodulated sound
carrier

98.0

60 to 100 dB

SYMBOL

PARAMETER

CONDITIONS

MIN.

MAX.

UNIT

VSWR

reflection coefficient

referred to 75

impedance

(worst case on or between picture
and sound carrier at maximum gain):

all channels in TV mode

FM (centre of channel)

PSM

surge protection voltage

ant

antenna connection disturbance
voltage

<1.75 GHz

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

General characteristics

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

frequency range:

FM band

87.50

108.00

MHz

low band

45.75

168.25

MHz

mid band

175.25

447.25

MHz

high band

455.25

855.25

MHz

margin:

for FM band

MHz

for low band

1.5

MHz

for mid/high band

MHz

image rejection (nominal gain to
10 dB gain reduction):

low band

mid band

<300 MHz

mid band

>300 MHz

high band (channel 14 to 69)

IF rejection (picture)

IF susceptibility:

low, mid band

high band

cross modulation:

in-channel

in-band

low band (n

mid band (n

high band (n

out of band

100

breakthrough susceptibility:

channel A to 69

osc

oscillator voltage at all pins

oscillators lock-in time

charge pump set logic HIGH

150

the video signal-to-sound
interference ratio with the tuner
exposed to sound signals in the
audio frequency range
100 Hz to 10 kHz and sound
pressure levels up to 105 dB
(20

Pa)

audio S/N ratio

ESD

electrostatic discharge (ESD)
on all pins

note 1

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

Note

1. All the pins of the desktop video tuner are protected against electrostatic discharge (ESD) up to 2 kV. The product is

classified in category B

(``MIL-STD-883C").

FM radio characteristics

limiting sensitivity for (S+N)/N

test signal C1

test signal C3

S/N ratio:

test signal C1

mono at f = 22.5 kHz

mono at f = 75 kHz

stereo

test signal C3

i(FM)

FM image rejection

test signal C1

effective selectivity S

300

test signal C1 + C2

frequency response:

test signal C3;

3 dB points

lower

3 dB point

upper

3 dB point

kHz

AM suppression

test signal C1

FM AF output level at
terminal 20/21 (RMS value):

mono

test signal C1

stereo

test signal C3

120

175

230

stereo separation

test signal C3; 1 kHz

THD

total harmonic distortion:

test signal C3

stereo at 1 kHz

0.8

1.5

during overmodulation at
f =

100 kHz

1.5

SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

Video and audio characteristics (see Fig.2)

Digital AFC status

ADC word at I

C-bus during read operation

PARAMETER

TEST SIGNAL

TEST

POINT

MIN.

TYP.

MAX.

UNIT

CVBS characteristics:

video amplitude signal at pin 23

A1 (peak-to-peak value)

BU4

0.75

0.95

1.15

DC level sync pulse at pin 23

BU4

0.7

Video amplitude drop with respect to modulation
1 MHz at T

amb

= 45

at 2 MHz

BU4

1.5

at 3 MHz

BU4

2.5

1.5

at 4 MHz

BU4

4.0

2.0

at 4.43 MHz

BU4

4.0

2.0

Sound carrier rejection

A1 (1 MHz) + B1

BU4

Residual 40.40 MHz signal in video channel:
level of 1.5 MHz

A1 + B3

BU4

Residual 77.8 MHz signal in video channel

BU4

Second IF sound output level at level of 6.0 MHz

A1 (black) + B1

BU5

Test on 2T pulse at T

amb

= 45

2T pulse/bar response

BU4

2.8

2T pulse response

BU4

3.5

CVBS S/N (unweighted)

A1 + B1

BU4

Gain limited sensitivity at 1 dB reduction
of video output

BU4

Maximum usable single input signal

BU4

Audio characteristics:

AF output level measured via LP 200 kHz filter,
RMS detector, 50

s de-emphasis

A1 + B2

BU6

250

350

450

THD (Total Harmonic Distortion) measured
via LP 200 kHz filter, RMS detector,
50

s de-emphasis

A1 + B2

BU6

0.5

S/N measured via CCIR filter, peak
CCIR detector, 50

s de-emphasis

A1 (full field colour bar)
+ B1

BU6

AM suppression ratio

A1 (black) + B2

BU6

Aerial input level for S/N = 41 dB

A1 (black) + B2

BU6

DIGITAL

READ-OUT

FREQUENCY

(kHz)

125

62.5

125

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

APPLICATION INFORMATION

A detailed description of the I

C-bus specification, with applications, is given in brochure

``The I

C-bus and how to

use it''. This brochure may be ordered using the code number 9398 393 40011.

WRITE mode

Note

1. A = Acknowledge.

DDRESS SELECTION

= +5 V (PLL supply voltage).

Note

1. If the AS pin is left floating, the internal bias will automatically set the address to C2.

ROGRAMMABLE DIVIDER SETTINGS

(

BYTES

AND

Divider ratio:

N = 16

× {

RF(pc)

+ f

IF(pc)

}, where (pc) is picture carrier and f

and f

are expressed in MHz.

osc

(MHz).

N = (8192

n13) + (4096

n12) + (2048

n11) + (1024

n10) + (512

n9) + (256

n8) + (128

n7) + (64

n6) +

(32

n5) + (16

n4) + (8

n3) + (4

n2) + (2

n1) + n0

For FM radio, f

IF(fm)

= 10.70 MHz

N = (f

+ f

IF(fm)

)/step size = (f

+ f

IF(fm)

)/50 kHz = 20

+ f

IF(fm)

)

BYTE

BITS

MSB

LSB

(1)

Address byte

MA1

MA0

Program divider byte 1

n14

n13

n12

n11

n10

Program divider byte 2

Control information byte 1

RSA

RSB

Control information byte 2

MA1

MA0

ADDRESS

VOLTAGE AT PIN 15 (see note 1)

0.0V

to 0.1V

0.2V

to 0.3V

0.4V

to 0.6V

0.9V

to 1.0V

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

ONTROL BYTE

Charge pump settings:

CP = 1, for fast tuning

CP = 0, for moderate speed tuning with slightly better residual oscillator FM.

It is recommended to set CP = 1 at all times in the TV mode. In the FM radio mode, set CP = 1 only during the search
tuning. Once the wanted channel is obtained, set CP = 0 to get the best signal-to-noise ratio.

Test mode settings:

T2 = T1 = 0; T0 = 1, for normal operation.

PLL disabling:

OS = 0, for normal operation

OS = 1, for switching the charge pump to the high impedance state. I

output voltage is LOW.

Ratio select bits

ORTS BYTE

Notes

1. If the TV function is not required, the tuner can be switched to power-down mode. In this mode the tuner reduces the

current consumption by up to 100 mA.

2. By this setting the FM radio AFC status can be read from the A/D bits in the status byte.

3. By this setting the RF input level can be read from the A/D bits in the status byte.

RSA

RSB

STEP SIZE

50 kHz (for FM band)

31.25 kHz (for slow picture search)

62.5 kHz (for normal picture search)

FUNCTION

BIT

TV/FM bandswitching

FM band

Low band

Mid band

High band

TV mode

Power down mode; see note 1

System I negative mode

FM radio mode

AFC; see note 2

; see note 3

Mono

Mute

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

ELEGRAM EXAMPLES

(WRITE

MODE

)

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Pb - Ack - Stop.

Start - Adb - Ack - Cb - Ack - Pb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Cb - Ack - Stop.

Start - Adb - Ack - Db1 - Ack - Db2 - Ack - Stop.

Where:

Start = start condition

Adb = address byte

Ack = acknowledge

Db1 = divider byte 1

Db2 = divider byte 2

Cb = control byte

Pb = ports byte

Stop = stop condition.

READ mode

The in-lock can be read by setting the R/W bit to 1.

Notes

1. POR = Power On Reset. POR is internally set to 1 in case V

drops below 3 V. The POR bit is reset when an end of

data is detected by the PLL IC.

2. FL = In-lock flag; FL = 1: loop is phase-locked. The loop must be phase-locked during at least 8 periods of the internal

reference frequency (either 7.8125 kHz, 3.90625 kHz or 6.25 kHz) before the FL flag is internally set to 1.

3. I2, I1 and I0 = digital information for I/O ports P2, P1 and P0 respectively.

4. A2, A1 and A0 = built-in 5-level A/D converter on the internal I/O port P6 (see Table "Digital AFC status").

5. A = Acknowledge.

ELEGRAM EXAMPLES

(READ

MODE

)

Start - Adb - Ack - STB - Ack - STB - - Stop (no Ack from processor = End-of-data).

Start - Adb - Ack - STB - - Stop (no Ack from processor = End-of-data).

Where:

STB = Status byte.

BYTE

BITS

MSB

LSB

(5)

Address byte

MA1

MA0

Status byte

POR

(1)

(2)

(3)

(4)

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

Aerial connections

Standard-phono socket female 75

or IEC (female for TV,

male for FM radio).

Solderability

The solderability of pins and mounting tags when tested
initially and after 16 hours steam ageing in accordance
with

``IEC 68-2-20'', test Ta, method 1 (solder bath

235

C for 2

5 s), results in a wetted area of 95%.

No de-wetting will occur when soldered at
260

C for 5

0.5 s.

Resistance to soldering heat

The product will not be damaged when tested in
accordance with

``IEC 68-2-20'', test Tb, method 1A

(solder bath 260

C for 5

1 s).

Mass

Approximately 50 g.

Robustness of pins

The pins will not be damaged when tested in accordance
with

``IEC 68-2-21'' :

Test Ua1, tensile of 20 N in axial direction

Test Ua2, thrust of 4 N in axial direction

Test Ua2, thrust of 2 N in axial direction.

Punching pattern of chassis PCB

Field rejects are often related to broken tag joints.
Therefore, the following punching pattern is recommended
(see Fig.6).

Fig.6 Punching pattern seen from solder side.

Dimensions in mm.

handbook, full pagewidth

59.2

14.7

4.445

2.1

1.1

34.7

3.5

4.6

78.4

0.9

0.1

unit

contour

CCA509

2.6

1997 May 14

Philips Components

Preliminary specification

Desktop video & FM radio module
system CCIR I

FM1246

DEFINITIONS

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

PURCHASE OF PHILIPS I

C COMPONENTS

Data sheet status

Objective specification

This data sheet contains target or goal specifications for product development.

Preliminary specification

This data sheet contains preliminary data; supplementary data may be published later.

Product specification

This data sheet contains final product specifications.

Application information

Where application information is given, it is advisory and does not form part of the specification.

Purchase of Philips I

C components conveys a license under the Philips' I

C patent to use the

components in the I

C system provided the system conforms to the I

C specification defined by

Philips. This specification can be ordered using the code 9398 393 40011.

Philips Components a worldwide company

Argentina: Ierod, BUENOS AIRES,

Tel. (01) 786 7635, Fax. (01) 786 9397.

Australia: Philips Components Pty Ltd, NORTH RYDE,

Tel. (02) 9805 4455, Fax. (02) 9805 4466.

Austria: Österreichische Philips Industrie GmbH, WIEN,

Tel. (01) 601 01 12 41, Fax. (01) 60 101 12 11.

Belarus: Philips Office Belarus, MINSK,

Tel. (5172) 200 915, Fax. (5172) 200 773.

Benelux: Philips Nederland B.V., EINDHOVEN, NL.,

Tel. (+31 40) 2783 749, Fax. (+31 40) 2788 399.

Brazil: Philips Components, SÃO PAULO,

Tel. (011) 821 2333, Fax. (011) 829 1849.

Canada: Philips Electronics Ltd., SCARBOROUGH,

Tel. (0416) 292 5161, Fax. (0416) 754 6248.

China: Philips Company, SHANGHAI,

Tel. (021) 6485 0600, Fax. (021) 6485 5615.

Colombia: Iprelenso Ltda, SANTAFE DE BOGOTA,

Tel. (01) 345 8713, Fax. (01) 345 8712.

Denmark: Philips Components A/S, COPENHAGEN S,

Tel. (32) 883 333, Fax. (31) 571 949.

Finland: Philips Components, ESPOO,

Tel. 9 (0)-615 800, Fax. 9 (0)-615 80510.

France: Philips Composants, SURESNES,

Tel. (01) 4099 6161, Fax. (01) 4099 6427.

Germany: Philips Components GmbH, HAMBURG,

Tel. (040) 2489-0, Fax. (040) 2489 1400.

Greece: Philips Hellas S.A., TAVROS,

Tel. (01) 4894 339/(01) 4894 239, Fax. (01) 4814 240.

Hong Kong: Philips Hong Kong, KOWLOON,

Tel. 2784 3000, Fax. 2784 3003.

India: Philips India Ltd., BOMBAY,

Tel. (022) 4938 541, Fax. (022) 4938 722.

Indonesia: P.T. Philips Development Corp., JAKARTA,

Tel. (021) 520 1122, Fax. (021) 520 5189.

Ireland: Philips Electronics (Ireland) Ltd., DUBLIN,

Tel. (01) 76 40 203, Fax. (01) 76 40 210.

Israel: Rapac Electronics Ltd., TEL AVIV,

Tel. (03) 6450 444, Fax. (03) 6491 007.

Italy: Philips Components S.r.l., MILANO,

Tel. (02) 6752 2531, Fax. (02) 6752 2557.

Japan: Philips Japan Ltd., TOKYO,

Tel. (03) 3740 5028, Fax. (03) 3740 0580.

Korea (Republic of): Philips Electronics (Korea) Ltd., SEOUL,

Tel. (02) 709 -1472, Fax. (02) 709 1480.

Malaysia: Philips Malaysia SDN Berhad

Components Division, PULAU PINANG,
Tel. (04) 657 0055, Fax. (04) 656 5951.

Mexico: Philips Components, EL PASO, U.S.A.,

Tel. (915) 772 4020, Fax. (915) 772 4332.

New Zealand: Philips New Zealand Ltd., AUCKLAND,

Tel. (09) 849 4160, Fax. (09) 849 7811.

Norway: Norsk A/S Philips, OSLO,

Tel. (22) 74 8000, Fax. (22) 74 8341.

Pakistan: Philips Electrical Industries of Pakistan Ltd., KARACHI,

Tel. (021) 587 4641-49, Fax. (021) 577 035/587 4546.

Philippines: Philips Semiconductors Philippines Inc.,

METRO MANILA, Tel. (02) 816 6380, Fax. (02) 817 3474.

Poland: Philips Poland Sp. z.o.o., WARSZAWA,

Tel. (022) 612 2594, Fax. (022) 612 2327.

Portugal: Philips Portuguesa S.A.,

Philips Components: LINDA-A-VELHA,
Tel. (01) 416 3160/416 3333, Fax. (01) 416 3174/416 3366.

Russia: Philips Russia, MOSCOW,

Tel. (095) 247 9124, Fax. (095) 247 9132.

Singapore: Philips Singapore Pte Ltd., SINGAPORE,

Tel. 350 2000, Fax. 355 1758.

South Africa: S.A. Philips Pty Ltd., JOHANNESBURG,

Tel. (011) 470 5911, Fax. (011) 470 5494.

Spain: Philips Components, BARCELONA,

Tel. (93) 301 63 12, Fax. (93) 301 42 43.

Sweden: Philips Components AB, STOCKHOLM,

Tel. (+46) 8 632 2000, Fax. (+46) 8 632 2745.

Switzerland: Philips Components AG, ZÜRICH,

Tel. (01) 488 22 11, Fax. (01) 481 77 30.

Taiwan: Philips Taiwan Ltd., TAIPEI,

Tel. (02) 388 7666, Fax. (02) 382 4382.

Thailand: Philips Electronics (Thailand) Ltd., BANGKOK,

Tel. (02) 745 4090, Fax. (02) 398 0793.

Turkey: Türk Philips Ticaret A.S., GÜLTEPE/ISTANBUL,

Tel. (0212) 279 2770, Fax. (0212) 282 6707.

Ukraine: Philips Ukraine Ltd., KIEV,

Tel. (044) 268 7327, Fax. (044) 268 6323.

United Kingdom: Philips Components Ltd., DORKING,

Tel. (01306) 512 000, Fax. (01306) 512 345.

United States:

· Philips Components, JUPITER, FL,

Tel. (561) 745 3300, Fax. (561) 745 3600.

· For literature: (800) 447 3762.

· Display and Wire Wound Components, ANN ARBOR, MI,

Tel. (313) 996 9400, Fax. (313) 761 2776.

· Magnetic Products, SAUGERTIES, NY,

Tel. (914) 246 2811, Fax. (914) 246 0487.

Uruguay: Philips Components, MONTEVIDEO,

Tel. (02) 704 044, Fax. (02) 920 601.

For all other countries apply to: Philips Components,
Marketing Communications, P.O. Box 218, 5600 MD EINDHOVEN,
The Netherlands, Fax. +31-40-2724 547.

COD11

All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or
contract, is believed to be accurate and reliable and may be changed without notice.
No liability will be accepted by the publisher for any consequence of its use. Publication
thereof does not convey nor imply any license under patent- or other industrial or
intellectual property rights.

Printed in The Netherlands

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: FM1246

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: FM1246