Product Specification
2 / 28
LM170E01
Liquid Crystal Display
Ver 1.1
Feb. 24, 2003
CONTENTS
NO.
ITEM
Page
-
COVER
1
-
CONTENTS
2
-
RECORD OF REVISIONS
3
1
GENERAL DESCRIPTION
4
2
ABSOLUTE MAXIMUM RATINGS
5
3
ELECTRICAL SPECIFICATIONS
6
3-1
ELECTRICAL CHARACTERISTICS
6
3-2
INTERFACE CONNECTIONS
8
3-3
SIGNAL TIMING SPECIFICATIONS
12
3-4
SIGNAL TIMING WAVEFORMS
13
3-5
COLOR INPUT DATA REFERANCE
14
3-6
POWER SEQUENCE
15
4
OPTICAL SPECIFICATIONS
17
5
MECHANICAL CHARACTERISTICS
21
6
RELIABILITY
24
7
INTERNATIONAL STANDARDS
25
7-1
SAFETY
25
7-2
EMC
25
8
PACKING
26
8-1
DESIGNATION OF LOT MARK
26
8-2
PACKING FORM
26
9
PRECAUTIONS
27
3-7
VCC POWER DIP CONDITION
16
Product Specification
3 / 28
LM170E01
Liquid Crystal Display
Ver 1.1
Feb. 24, 2003
RECORD OF REVISIONS
Revision No
Description
Date
Page
Ver 1.0
Ver 1.1
Final draft
General feature : Power consumption
3-1 Electrical characteristics
Power supply input current
Power consumption
4. Optical characteristics
Gray scale
Feb. 14. 2003
Feb. 24. 2003
-
4/28
6/28
18/28
Product Specification
4 / 28
LM170E01
Liquid Crystal Display
Ver 1.1
Feb. 24, 2003
1. General Description
The LM170E01-A4 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally white mode. This TFT-LCD has a 17.0 inch diagonal
measured active display area with SXGA resolution(1024 vertical by 1280 horizontal pixel array)
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus, presenting a palette of more than 16.2M colors with FRC(Frame Rate Control).
The LM170E01-A4 has been designed to apply the interface method that enables low power, high speed,low
EMI. FPD Link or compatible must be used as a LVDS(Low Voltage Differential Signaling) chip.
The LM170E01-A4 is intended to support applications where thin thickness,wide viewing angle, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels,
the LM170E01-A4 characteristics provide an excellent flat panel display for office automation products such as
monitors.
General Features
Outline Dimension
358.5(H) x 296.5(V) x 17.0(D) mm(Typ.)
Active screen size
17.0 inch (43.27cm) diagonal
Pixel Pitch
0.264 mm x 0.264 mm
Pixel Format
1280 horiz. by 1024 vert. Pixels. RGB stripe arrangement
Display Colors
16.2M colors
Luminance, white
250 cd/m
2
(Typ. Center 1 point)
Power Consumption
19.05 Watts(Typ.)
Weight
1890g (Typ.)
Display operating mode
Transmissive mode, normally white
Surface treatments
Hard coating (3H), Anti-glare treatment of the front polarizer
CN1
(30pin)
LVDS
pair #1
LVDS
pair #2
Power
Circuit
Block
+5.0V
V
CC
Ro
w
Dr
i
v
e
r
circ
u
i
t
Column Driver Circuit
TFT-LCD
(1280 x RGB x 1024 pixels)
G1
S1
S1280
G1024
Backlight Assembly(4CCFL)
CN2,3
CN4,5
LVDS Rx &
Timing Controller
Column Driver circuit
Figure 1. Block diagram
Product Specification
5 / 28
LM170E01
Liquid Crystal Display
Ver 1.1
Feb. 24, 2003
2. Absolute maximum ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
Table 1. Absolute Maximum Ratings
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 C Max, and no condensation of water.
Parameter
Notes
Symbol
Values
Units
Min.
Max.
Power Supply Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
At 25
1
1
1
1
V
CC
T
OP
T
ST
H
OP
H
ST
0.3
0
20
10
10
5.5
50
60
90
90
V
dc
%RH
%RH
90%
10
20
30
40
50
60
70
80
0
-20
0
10
20
30
40
50
Dry Bulb Temperature [C]
Wet Bulb
Temperature [C]
Storage
Operation
Humi
dit
y [
(%)
RH
]
10%
40%
60%
60
Figure 2. Temperature and relative humidity
PDF 
ZIP