ChipFind - документация

Электронный компонент: TDA6111

Скачать:  PDF   ZIP
DATA SHEET
Preliminary specification
Supersedes data of February 1992
File under Integrated Circuits, IC02
1995 Feb 07
INTEGRATED CIRCUITS
Philips Semiconductors
TDA6111Q
Video output amplifier
1995 Feb 07
2
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
FEATURES
High bandwidth and high slew rate
Black-current measurement output for Automatic
Black-current Stabilization (ABS)
Two cathode outputs; one for DC currents, and one for
transient currents
A feedback output separated from the cathode outputs
Internal protection against positive appearing
Cathode-Ray Tube (CRT) flashover discharges
ESD protection
Simple application with a variety of colour decoders
Differential input with a designed maximum common
mode input capacitance of 3 pF, a maximum differential
mode input capacitance of 0.5 pF and a differential input
voltage temperature drift of 50
V/K
Defined switch-off behaviour.
GENERAL DESCRIPTION
The TDA6111Q is a video output amplifier with 16 MHz
bandwidth. The device is contained in a single in-line 9-pin
medium power (DBS9MPF) package, using high-voltage
DMOS technology, intended to drive the cathode of a
colour CRT.
QUICK REFERENCE DATA
ORDERING INFORMATION
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
V
DDH
high level supply voltage
0
-
250
V
V
DDL
low level supply voltage
0
-
14
V
I
DDH
quiescent high voltage supply current
V
oc
= 0.5V
DDH
7.0
9.0
11.0
mA
I
DDL
quiescent low voltage supply current
V
oc
= 0.5V
DDH
5.0
6.8
8.0
mA
V
I
input voltage
0
-
V
DDL
V
V
oc
, V
fb
output voltage
V
DDL
-
V
DDH
V
T
stg
storage temperature
-
55
-
+150
C
T
amb
operating ambient temperature
-
20
-
+65
C
TYPE NUMBER
PACKAGE
NAME
DESCRIPTION
VERSION
TDA6111Q
DBS9MPF
plastic DIL-bent-SIL medium power package with fin; 9 leads
SOT111-1
1995 Feb 07
3
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
BLOCK DIAGRAM
Fig.1 Block diagram.
handbook, full pagewidth
DIFFERENTIAL
STAGE
MIRROR
MIRROR
CURRENT
SOURCE
MIRROR
MIRROR
TDA6111Q
7 V
supply voltage
input HIGH
feedback
output
6
Vbias
FOLLOWERS
C par
9
non-inverting
input
inverting
input
3
1
4
2
ground
(substrate)
supply voltage
input LOW
7
8
5
cathode
transient
output
cathode
DC output
black current
measurement
output
MGA058
1995 Feb 07
4
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
PINNING
SYMBOL
PIN
DESCRIPTION
V
ip
1
non-inverting voltage input
V
DDL
2
supply voltage LOW
V
in
3
inverting voltage input
GND
4
ground, substrate
I
om
5
black current measurement
output
V
DDH
6
supply voltage HIGH
V
cn
7
cathode transient voltage output
V
oc
8
cathode DC voltage output
V
fb
9
feedback voltage output
Fig.2 Pin configuration.
andbook, halfpage
MGA057
1
2
3
4
5
6
7
8
9
DDL
V
GND
TDA6111Q
ip
V
in
V
om
I
oc
V
cn
V
fb
V
DDH
V
1995 Feb 07
5
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134). Voltages measured with respect to GND (pin 4);
currents as specified in Fig.1; unless otherwise specified.
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling MOS devices (see
"Handling MOS Devices" ).
QUALITY SPECIFICATION
Quality specification
"SNW-FQ-611 part E" is applicable, except for ESD Human body model see Chapter "Limiting
values", and can be found in the
"Quality reference handbook" (ordering number 9398 510 63011).
THERMAL CHARACTERISTICS
Note
1. External heatsink is required.
SYMBOL
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
V
DDH
high level supply voltage
0
250
V
V
DDL
low level supply voltage
0
14
V
V
I
input voltage
0
V
DDL
V
V
Idm
differential mode input voltage
-
6
+6
V
V
om
measurement output voltage
0
V
DDL
V
oc
cathode output voltage
V
DDL
V
DDH
V
V
fb
feedback output voltage
V
DDL
V
DDH
V
I
in
,I
ip
input current
0
1
mA
I
ocsmL
low non-repetitive peak cathode
output current
flashover discharge = 100
C
0
5
A
I
ocsmH
high non-repetitive peak cathode
output current
flashover discharge = 100 nC
0
10
A
P
tot
total power dissipation
0
4
W
T
stg
storage temperature
-
55
+150
C
T
j
junction temperature
-
20
+150
C
V
es
electrostatic handling
human body model (HBM)
-
> 1500
V
machine model (MM)
-
> 400
V
SYMBOL
PARAMETER
VALUE
UNIT
R
th j-c
thermal resistance from junction to case (note 1)
12
K/W
1995 Feb 07
6
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
CHARACTERISTICS
Operating range: T
amb
=
-
20 to 65
C; V
DDH
= 180 to 210 V; V
DDL
= 10.8 to 13.2 V; V
ip
= 2.6 to 5 V;
V
om
= 1.4 V to V
DDL
.
Test conditions (unless otherwise specified): T
amb
= 25
C; V
DDH
= 200 V; V
DDL
= 12 V; V
ip
= 5 V; V
om
= 6 V; C
L
= 10 pF
(C
L
consists of parasitic and cathode capacitance); R
th-heatsink
= 10 K/W; measured in test circuit Fig.3.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
I
DDH
quiescent HIGH voltage supply current V
oc
= 0.5V
DDH
7.0
9.0
11.0
mA
I
DDL
quiescent LOW voltage supply current
V
oc
= 0.5V
DDH
5.0
6.8
8.0
mA
I
bias
input bias current
V
oc
= 0.5V
DDH
0
-
40
A
I
offset
input offset current
V
oc
= 0.5V
DDH
-
6
-
+6
A
I
om(offset)
offset current of measurement output
I
oc
= 0
A;
-
1.0 V < V
1
-
3
< 1.0 V;
1.4 V < V
om
< V
DDL
-
10
0
+10
A
linearity of current transfer
-
10
A < I
oc
< 3 mA;
-
1.0 V < V
1
-
3
< 1.0 V;
1.4 V < V
om
< V
DDL
0.9
1.0
1.1
V
offset
input offset voltage
V
oc
= 0.5V
DDH
-
50
-
+50
mV
V
oc(min)
minimum output voltage
V
1
-
3
=
-
1 V
-
-
20
V
V
oc(max)
maximum output voltage
V
1
-
3
=
-
1 V
V
DDH
-
12
-
-
V
GB
gain-bandwidth product of open-loop
gain: V
fb
/ V
i, dm
f = 500 kHz; V
ocDC
= 100 V
-
1.6
-
GHz
B
S
small signal bandwidth
V
ocAC
= 60 V (p-p);
V
ocDC
= 100 V
13
16
-
MHz
B
L
large signal bandwidth
V
ocAC
= 100 V (p-p);
V
ocDC
= 100 V
10
13
-
MHz
t
pd
cathode output propagation delay time
50% input to 50% output
V
ocAC
= 100 V (p-p);
V
ocDC
= 100 V square
wave; f < 1 MHz;
t
r
= t
f
= 22 ns;
see Figs 4 and 5
17
23
29
ns
t
r
cathode output rise time 10% output to
90% output
V
oc
= 50 to 150 V square
wave; f < 1 MHz; t
f
= 22 ns;
see Fig.4
23
30
36
ns
t
f
cathode output fall time 90% output to
10% output
V
oc
= 150 to 50 V square
wave; f < 1 MHz; t
r
= 22 ns;
see Fig.5
23
30
36
ns
t
s
settling time 50% input to
(99% < output < 101%)
V
ocAC
= 100 V (p-p);
V
ocDC
= 100 V square
wave; f < 1 MHz;
t
r
= t
f
= 22 ns;
see Figs 4 and 5
-
-
350
ns
SR
slew rate between 50 V to 150 V
V
1
-
3
= 2 V (p-p) square
wave; f < 1 MHz;
t
r
= t
f
= 22 ns
-
3000
-
V/
s
I
om
I
oc
------------
1995 Feb 07
7
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
Notes
1. If the difference between V
DDL
and V
ip
is less than 7 V, overshoot cannot be specified.
2. SVRR: The ratio of the change in supply voltage to the change in input voltage when there is no change in output
voltage.
O
v
cathode output voltage overshoot
V
ocAC
= 100 V (p-p);
V
ocDC
= 100 V square
wave; f < 1 MHz;
t
r
= t
f
= 22 ns;
see Figs 4 and 5; note 1
-
9
-
%
SVRRH
high supply voltage rejection ratio
f < 50 kHz; note 2
-
85
-
dB
SVRRL
low supply voltage rejection ratio
f < 50 kHz; note 2
-
70
-
dB
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Cathode output
The cathode output is protected against peak currents
(caused by positive voltage peaks during high-resistance
flash) of 5 A maximum with a charge content of 100
C.
The cathode is also protected against peak currents
(caused by positive voltage peaks during low-resistance
flash) of 10 A maximum with a charge content of 100 nC.
Flashover protection
The TDA6111Q incorporates protection diodes against
CRT flashover discharges that clamp the cathode output
pin to the V
DDH
pin. The DC supply voltage at the V
DDH
pin
has to be within the operating range of 180 to 210 V to
ensure that the Absolute Maximum Rating for V
DDH
of
250 V will not be exceeded during flashover. To limit the
diode current, an external 680
carbon high-voltage
resistor in series with the cathode output and a 2 kV spark
gap are needed (for this resistor-value, the CRT has to be
connected to the main PCB). This addition produces an
increase in the rise and fall times of approximately 5 ns
and a decrease in the overshoot of approximately 4%.
V
DDH
to GND must be decoupled:
1. With a capacitor >20 nF with good HF behaviour
(e.g. foil). This capacitance must be placed as close
as possible to pins 6 and 4, but definitely within 5 mm.
2. With a capacitor >10
F on the picture tube base print
(common for three output stages).
V
DDL
to GND must be decoupled:
1. With a capacitor >20 nF with good HF behaviour
(e.g. ceramic). This capacitance must be placed as
close as possible to pins 2 and 4, but definitely within
10 mm.
Switch-off behaviour
The switch-off behaviour of the TDA6111Q is defined:
when the bias current becomes zero, at V
DDL
(pin 2) lower
than approximately 5 V, all the output pins
(pins 7, 8 and 9) will be high.
1995 Feb 07
8
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
C
par
= 150 fF.
Fig.3 Test circuit with feedback factor
1
/
83
.
handbook, full pagewidth
C3
3.9 pF
R9
820
C2
22
F
C1
22 nF
C5
22 nF
C6
100 nF
R10
68.1 k
12 V
200 V
3
9
2
6
1
4
5
8
7
TDA6111Q
R1
50
C10
100 nF
C9
136 pF
R3
20 M
C7
3.2 pF
C8
6.8 pF
R2
1 M
1.4 mA
5 V
om
V
6 V
probe
V
i
n
C
560 pF
MGA059 - 1
C par
A
C4
10
F
C7 10
F
1995 Feb 07
9
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
Fig.4 Output voltage (pin 8) rising edge as a function of the AC input signal.
150
140
100
60
50
151
149
s
t
overshoot (in %)
t
t
0
x
x
t r
pd
t
Voc
Vi
MGA974
1995 Feb 07
10
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
Fig.5 Output voltage (pins 8) falling edge as a function of the AC input signal.
150
140
100
60
50
51
49
s
t
overshoot (in %)
t
t
0
x
x
t f
pd
t
Voc
Vi
MGA975
1995 Feb 07
11
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
TEST AND APPLICATION INFORMATION
Dissipation
Regarding dissipation, distinction must first be made
between static dissipation (independent of frequency) and
dynamic dissipation (proportional to frequency).
The static dissipation of the TDA6111Q is due to high and
low voltage supply currents and load currents in the
feedback network and CRT.
The static dissipation equals:
R
fb
= value of feedback resistor.
I
oc
= DC value of cathode current.
With V
fb
= V
oc
= 100 V, R
fb
= 68 k
, I
oc
= 0.6 mA and
other typical conditions as mentioned in Chapter
"Characteristics", the static dissipation P
stat
= 2.0 W.
P
stat
V
DDL
I
DDL
V
DDH
I
DDH
V
oc
I
oc
V
fb
V
fb
R
fb
--------
+
+
=
The dynamic dissipation equals:
P
dyn
= V
DDH
(C
L
+ C
fb
+ C
int
)
f
i
V
o(p-p)
C
L
= load capacitance.
C
fb
= feedback capacitance (
150 fF).
C
int
= internal load capacitance (
4 pF).
f
i
= input frequency.
V
o(p-p)
= output voltage (peak-to-peak value).
= non-blanking duty-cycle (
0.8).
With C
L
= 10 pF, C
fb
= 0, C
int
= 4 pF, f
i
= 8 MHz
(simulation of worst-case noise), V
o(p-p)
= 100 V and
= 80% then P
dyn
= 1.8 W
The IC must be mounted on the picture tube base print to
minimize the load capacitance (C
L
).
The total power dissipation, P
tot
= P
stat
+ P
dyn
thus
amounts to 3.6 W under given conditions.
From T
j
= T
amb
+ P
tot
R
th j-a
< T
j(max)
= 150
C, R
th j-a
of
the package and heatsink together must be < 24 K/W.
1995 Feb 07
12
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
PACKAGE OUTLINE
UNIT
A
A
3
b
1
D
1
2
b
2
b
c
D
(1)
E
(1)
Z
(1)
e
L
P
P
1
q
1
q
2
q
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
EIAJ
mm
18.5
17.8
8.7
8.0
A
4
15.5
15.1
1.40
1.14
0.67
0.50
1.40
1.14
0.48
0.38
21.8
21.4
21.4
20.7
6.48
6.20
3.4
3.2
2.54
e
2.54
1.0
65
55
5.9
5.7
4.4
4.2
3.9
3.4
15.1
14.9
Q
1.75
1.55
DIMENSIONS (mm are the original dimensions)
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
2.75
2.50
SOT111-1
92-11-17
95-03-11
0
5
10 mm
scale
0.25
w
D
E
A
A
c
A
2
3
A
4
q
1
q
2
L
e
2
Q
w
M
b
b
1
b
2
D
1
P
q
1
Z
e
1
9
P
seating plane
pin 1 index
o
o
DBS9MPF: plastic DIL-bent-SIL medium power package with fin; 9 leads
SOT111-1
A
max.
max.
2
3.7
1995 Feb 07
13
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
SOLDERING
Plastic single in-line packages
B
Y DIP OR WAVE
The maximum permissible temperature of the solder is
260
C; this temperature must not be in contact with the
joint for more than 5 s. The total contact time of successive
solder waves must not exceed 5 s.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified storage maximum. If the printed-circuit board has
been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within
the permissible limit.
R
EPAIRING SOLDERED JOINTS
Apply the soldering iron below the seating plane (or not
more than 2 mm above it). If its temperature is below
300
C, it must not be in contact for more than 10 s; if
between 300 and 400
C, for not more than 5 s.
DEFINITIONS
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
1995 Feb 07
14
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
NOTES
1995 Feb 07
15
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6111Q
NOTES
Philips Semiconductors
Philips Semiconductors a worldwide company
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. (02)805 4455, Fax. (02)805 4466
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,
Tel. (01)60 101-1236, Fax. (01)60 101-1211
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,
Tel. (31)40 783 749, Fax. (31)40 788 399
Brazil: Rua do Rocio 220 - 5
th
floor, Suite 51,
CEP: 04552-903-SO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Tel. (011)821-2333, Fax. (011)829-1849
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:
Tel. (800) 234-7381, Fax. (708) 296-8556
Chile: Av. Santa Maria 0760, SANTIAGO,
Tel. (02)773 816, Fax. (02)777 6730
Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17,
77621 BOGOTA, Tel. (571)249 7624/(571)217 4609,
Fax. (571)217 4549
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. (032)88 2636, Fax. (031)57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (9)0-50261, Fax. (9)0-520971
France: 4 Rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01)4099 6161, Fax. (01)4099 6427
Germany: P.O. Box 10 63 23, 20043 HAMBURG,
Tel. (040)3296-0, Fax. (040)3296 213.
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01)4894 339/4894 911, Fax. (01)4814 240
Hong Kong: PHILIPS HONG KONG Ltd., 15/F Philips Ind. Bldg.,
24-28 Kung Yip St., KWAI CHUNG, N.T.,
Tel. (852)424 5121, Fax. (852)480 6960/480 6009
India: Philips INDIA Ltd, Shivsagar Estate, A Block ,
Dr. Annie Besant Rd. Worli, Bombay 400 018
Tel. (022)4938 541, Fax. (022)4938 722
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,
P.O. Box 4252, JAKARTA 12950,
Tel. (021)5201 122, Fax. (021)5205 189
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. (01)640 000, Fax. (01)640 200
Italy: PHILIPS SEMICONDUCTORS S.r.l.,
Piazza IV Novembre 3, 20124 MILANO,
Tel. (0039)2 6752 2531, Fax. (0039)2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2 -chome, Minato-ku, TOKYO 108,
Tel. (03)3740 5028, Fax. (03)3740 0580
Korea: (Republic of) Philips House, 260-199 Itaewon-dong,
Yongsan-ku, SEOUL, Tel. (02)794-5011, Fax. (02)798-8022
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03)750 5214, Fax. (03)757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905,
Tel. 9-5(800)234-7381, Fax. (708)296-8556
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB
Tel. (040)783749, Fax. (040)788399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09)849-4160, Fax. (09)849-7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (022)74 8000, Fax. (022)74 8341
Pakistan: Philips Electrical Industries of Pakistan Ltd.,
Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,
KARACHI 75600, Tel. (021)587 4641-49,
Fax. (021)577035/5874546.
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474
Portugal: PHILIPS PORTUGUESA, S.A.,
Rua dr. Antnio Loureiro Borges 5, Arquiparque - Miraflores,
Apartado 300, 2795 LINDA-A-VELHA,
Tel. (01)4163160/4163333, Fax. (01)4163174/4163366.
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65)350 2000, Fax. (65)251 6500
South Africa: S.A. PHILIPS Pty Ltd.,
195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. (011)470-5911, Fax. (011)470-5494.
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03)301 6312, Fax. (03)301 42 43
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,
Tel. (0)8-632 2000, Fax. (0)8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZRICH,
Tel. (01)488 2211, Fax. (01)481 77 30
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West
Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978,
TAIPEI 100, Tel. (02)388 7666, Fax. (02)382 4382.
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong,
Bangkok 10260, THAILAND,
Tel. (662)398-0141, Fax. (662)398-3319.
Turkey: Talatpasa Cad. No. 5, 80640 GLTEPE/ISTANBUL,
Tel. (0 212)279 2770, Fax. (0212)282 6707
United Kingdom: Philips Semiconductors LTD.,
276 Bath Road, Hayes, MIDDLESEX UB3 5BX,
Tel. (0181)730-5000, Fax. (0181)754-8421
United States: 811 East Arques Avenue, SUNNYVALE,
CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556
Uruguay: Coronel Mora 433, MONTEVIDEO,
Tel. (02)70-4044, Fax. (02)92 0601
Internet: http://www.semiconductors.philips.com/ps/
For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BE-p,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. +31-40-724825
SCD38
Philips Electronics N.V. 1994
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.
Printed in The Netherlands
533061/1500/02/pp16
Date of release: 1995 Feb 07
Document order number:
9397 747 60011