DATA SHEET
Product specification
File under Integrated Circuits, IC02
1997 May 26
INTEGRATED CIRCUITS
TDA8012AM
Low power PLL FM demodulator for
satellite TV receivers
1997 May 26
2
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
FEATURES
High input sensitivity
Fully balanced two-pin Voltage Controlled Oscillator
(VCO)
Low input impedance (50
)
Low impedance video baseband output
Internal voltage stabilizer
Keyed Automatic Frequency Control (AFC) or peak AFC
Carrier detector
Automatic Gain Control (AGC) output.
APPLICATIONS
Digital Broadcast System (DBS) satellite receivers.
GENERAL DESCRIPTION
The TDA8012AM is a sensitive Phase Locked Loop (PLL)
Frequency Modulation (FM) demodulator for the second
Intermediate Frequency (IF) in satellite receivers.
It provides Automatic Gain Control (AGC) and Automatic
Frequency Control (AFC) outputs that can be used to
optimize the level and the frequency of the signal applied
at the input. During the search procedure, the AFC output
provides a signal used for carrier detection.
QUICK REFERENCE DATA
ORDERING INFORMATION
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
V
CC
supply voltage
4.75
5.0
5.25
V
I
CC
supply current
V
CC
= 5 V; T
amb
= 25
C
40
50
60
mA
V
i
input level
53
57
61
dB
V
f
c
operating carrier frequency
-
480
-
MHz
V
o(p-p)
video output signal amplitude
(peak-to-peak value)
frequency deviation = 25 MHz
-
1
-
V
TYPE
NUMBER
PACKAGE
NAME
DESCRIPTION
VERSION
TDA8012AM
SSOP20
plastic shrink small outline package; 20 leads; body width 4.4 mm
SOT266-1
1997 May 26
3
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
BLOCK DIAGRAM
Fig.1 Block diagram.
handbook, full pagewidth
MBH934
3
4
STABILIZER
VCO
VIDEO BUFFER
TDA8012AM
1
2
5
6
7
8
9
10
CDF1
CDF2
PD
+
PD
-
IFI1
IFI2
GND
CC
V
AGCO
Vth(AGC)
VIDEO
LF1
LF2
OSCGND
VCO1
VCO2
AFCF
KEY
AFC/CDO
AFCOS
20
19
18
17
16
15
14
13
12
11
CARRIER
DETECTOR
AFC
AGC
1997 May 26
4
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
PINNING
SYMBOL
PIN
DESCRIPTION
CDF1
1
carrier detector filter 1 input
CDF2
2
carrier detector filter 2 input
PD+
3
positive peak detector output
PD
-
4
negative peak detector output
IFI1
5
intermediate frequency input 1
IFI2
6
intermediate frequency input 2
GND
7
general ground
V
CC
8
supply voltage
AGCO
9
automatic gain control output
V
th(AGC)
10
automatic gain control threshold
voltage input
VIDEO
11
baseband signal output
LF1
12
loop filter 1 input
LF2
13
loop filter 2 input
OSCGND
14
oscillator ground
VCO1
15
oscillator tank circuit 1 input
VCO2
16
oscillator tank circuit 2 input
AFCF
17
automatic frequency control filter
input
KEY
18
key pulse input
AFC/CDO
19
automatic frequency control
/carrier detector output
AFCOS
20
automatic frequency control offset
input
Fig.2 Pin configuration.
handbook, halfpage
TDA8012AM
MBH931
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
CDF1
CDF2
IFI1
IFI2
GND
AGCO
VCC
Vth(AGC)
PD
+
PD
-
AFCOS
VIDEO
LF1
LF2
OSCGND
VCO1
VCO2
AFCF
KEY
AFC/CDO
FUNCTIONAL DESCRIPTION
The TDA8012AM is a low power PLL FM demodulator
designed for use in satellite TV reception systems.
The demodulator is based on a PLL structure including a
fully balanced two-pin VCO. A high gain IF amplifier
ensures a high input sensitivity. The video output voltage
is supplied through a highly-linear video buffer with a low
output impedance. The centre frequency of the VCO and
the loop characteristics can be set by external components
(see Fig.4).
The circuit provides an AGC signal which is used to drive
a gain-controlled IF amplifier (TDA8011T or TDA8010AM)
for a stable PLL demodulation characteristic.
An analog AFC voltage is available. This signal fits in with
the input of the A/D converter port of the PLL frequency
synthesizer (TSA5055). The AFC function may be keyed
to address D2MAC systems.
The TDA8012AM includes a Carrier Detector (CD) used
for channel detection during search procedures.
1997 May 26
5
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe it is
desirable to take normal precautions appropriate to handling MOS devices.
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
V
CC
supply voltage
-
0.3
+6.0
V
V
I(max)
voltage on all pins
-
0.3
V
CC
V
I
O(max)
output source current
-
10
mA
t
sc(max)
maximum short-circuit time on outputs
-
10
s
Z
L
AC load impedance at video output
600
-
T
stg
IC storage temperature
-
55
+150
C
T
j
junction temperature
-
150
C
T
amb
operating ambient temperature
-
10
+80
C
SYMBOL
PARAMETER
CONDITIONS
VALUE
UNIT
R
th j-a
thermal resistance from junction to ambient
in free air
120
K/W
1997 May 26
6
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
CHARACTERISTICS
Measured in the application circuit (see Fig.4) with the following conditions: V
CC
= 5 V, T
amb
= 25
C, f
c
= 480 MHz,
input level: 57 dB
V; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply
V
CC
supply voltage
4.75
5.0
5.25
V
I
CC
supply current
note 1
40
50
60
mA
Voltage controlled oscillator
K
VCO
VCO constant
4.75 < V
CC
< 5.25 V;
-
10 < T
amb
< 80
C
20
25
30
MHz/V
f
VCO(drift)
VCO frequency temperature dependence note 2
-
1
2.5
MHz
f
VCO(shift)
VCO frequency voltage dependence
4.75 < V
CC
< 5.25 V
-
300
750
kHz
Frequency demodulator
V
i
operating input level
note 3
53
57
61
dB
V
f
c
optimal operating carrier frequency
-
480
-
MHz
Z
i
input impedance
note 4
resistive part
-
50
-
inductive part
-
100
-
nH
K
D
phase detector constant
V
i
= 57 dB
V
-
0.42
-
V/rad
L
G
PLL loop gain
note 5
drift
-
2
-
dB
shift
-
2
-
dB
Z
o
differential output impedance of the
phase detector
1.8
2.3
2.8
k
f
cr(PLL)
PLL capture range
note 6
20
26
-
MHz
D
G
differential gain
note 7
-
2
-
%
D
P
differential phase
note 7
-
2
-
deg
IM3
third-order intermodulation distortion
note 8
47
-
-
dB
IM2
second-order intermodulation distortion
note 9
45
-
-
dB
Video output
V
o(p-p)
baseband signal amplitude
(peak-to-peak value)
frequency
deviation = 25 MHz
0.8
1.0
1.2
V
V
O
DC voltage level of video output
2.1
2.35
2.6
V
Z
o
output impedance
-
75
-
S/N
weighted baseband signal-to-noise ratio
note 10
58
61
-
dB
S
AM
Amplitude Modulation (AM) sensitivity
note 11
-
30
-
dB
1997 May 26
7
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
Notes
1. The DC supply current is measured with V
CC
= 5 V.
2. The VCO frequency drift is defined as the change in oscillator frequency for a variation of ambient temperature, on
the one hand from T
amb
= 25
C to T
amb
= 0
C and on the other hand from T
amb
= 25
C to T
amb
= 50
C. It is
measured in the application of Fig.4 with the following component values for the tank circuit:
Coil: 2.5 turns; diameter 2 mm; adjustable.
Capacitor: miniature ceramic plate capacitor NP0, 3.3 pF.
3. The circuit is designed for an input level of 57 dB
V. The maximum allowable input level for the PLL design is
61 dB
V. However, for levels different from 57 dB
V, the optimum loop filter values will be different from those given
for the 57 dB
V input level in the reference measuring set-up.
4. The input impedance is reduced to a resistor with a parallel reactance. The values are given at 480 MHz. In order to
reduce the radiation from the oscillator to the RF input, it is recommended to use a symmetrical drive.
5. The PLL loop gain shift and drift are given without loop filter shift and drift (non-temperature compensated external
components).
Automatic gain control (note 12)
TH
AGC
automatic gain control threshold as a
function of the voltage applied to pin 10
I
AGCO
= 0.5 mA;
V
10
= 0.1V
CC
-
-
53
dB
V
I
AGCO
= 0.5 mA;
V
10
= 0.9V
CC
61
-
-
dB
V
note 13
V
th(AGC)
(pin 10) not
connected
-
57
-
dB
V
LD
level detector
shift
V
CC
= 4.75 to 5.25 V
-
1
-
dB
drift
T
amb
=
-
10 to +80
C
-
1
-
dB
S
AGC
automatic gain control steepness
I
AGCO
= 0.5 mA; note 14
-
8
-
mA/dB
V
sat(AGC)
low level automatic gain control output
saturation voltage
I
AGCO
= 1 mA
-
200
500
mV
Keying pulse
t
key
input keyed pulse time period
-
64
-
s
t
W(key)
keyed pulse width
8
-
-
s
V
IL
LOW level input keyed pulse voltage
key on
-
-
0.8
V
V
IH
HIGH level input keyed pulse voltage
key off
3.0
-
-
V
Z
i
input impedance
1
10
-
k
AFC and carrier detector output (note 15)
I
L(pd)
peak detector leakage current
note 16
50
150
250
nA
automatic frequency control steepness
with unmodulated input signal
4.5
5.5
6.5
V/MHz
f
AFC(shift)
shift of automatic frequency control
voltage with respect to f
VCO
with
unmodulated 480 MHz input signal
V
CC
=
5%
-
180
500
kHz
f
AFC
(
drift)
drift of automatic frequency control
voltage with respect to f
VCO
T
amb
= 80
C; note 17
-
-
1.1
-
MHz
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
V
AFC
f
-----------------
1997 May 26
8
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
6. The capture range or lock-in range is defined as the range where the PLL gets in lock. This value depends strongly
on the loop filter characteristics.
7. Measurements with test signals in accordance with CCIR recommendation 473-3;
FM modulated signal with DBS parameters:
a) 625 lines PAL TV system
b) 16 MHz/V modulator sensitivity
c) 1 V (p-p) video signal
d) No SAW filter is used.
8. No SAW filter is used at the input:
a) 16 MHz/V modulator sensitivity
b) 4.43 MHz sine wave colour signal (660 mV (p-p))
c) 3.25 MHz sine wave luminance signal (700 mV (p-p))
d) CCIR pre-emphasis
e) Intermodulation distance is defined as the distance between the luminance signal and the intermodulation
products.The video output spectrum is measured on pin 11 (point A of Fig.4) with a high resistance probe.
The de-emphasis figure is obtained from the measured data by calculation.
9. No SAW filter is used at the input:
a) 16 MHz/V modulator sensitivity
b) Two sound carriers at 7.02 MHz and 7.20 MHz; 4 MHz deviation
c) Intermodulation measurement without pre-emphasis
d) Intermodulation distance is defined as the distance between one of the sound carriers and the intermodulation
products
e) The video output spectrum is measured on pin 11 (point A of Fig.4) with a high resistance probe and a spectrum
analyser.
10. Measurements are made under the following conditions
a) FM modulator video signal
b) Amplitude level: 57 dB
V
c) Frequency: 479.5 MHz
d) Frequency deviation: 16 MHz
e) CCIR pre-emphasis + unified weighting filter
f) C/N > 50 dB
S/N is measured after de-emphasis with a baseband spectrum from 200 kHz to 5 MHz.
11. The AM sensitivity is defined as the ratio of the baseband output signals obtained from either an AM or FM modulated
RF input signal.
FM modulated signal: f
c
= 480 MHz, frequency deviation = 25 kHz, modulation frequency = 20 kHz, input
level = 57 dB
V
AM modulated signal: f
c
= 480 MHz, modulation depth = 50%, modulation frequency = 20 kHz, input
level = 57 dB
V.
12. The characteristics of the AGC function are measured in the application circuit of Fig.4. The circuit illustrated in Fig.4
has been designed to set the maximum AGC current to 1 mA. The output of the AGC function is capable of handling
up to 5 mA. The maximum AGC current can be increased to 5 mA by decreasing the value of the resistor connected
between pins 8 and 9.
S
AM
20 log
V
o(FM)
V
o(AM)
----------------
=
1997 May 26
9
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
13. For applications in which a fixed AGC threshold is used, it is recommended to use the internal resistor voltage divider
for lower AGC threshold spread. In this case, the threshold is set to 57 dB
V.
14. In the application circuit (see Fig.4) the voltage at the AGC output decreases when the IF input level increases above
the adjusted AGC threshold.
15. The outputs from the AFC and carrier detector are combined at pin 19 (see Fig.3). During search tuning, when the
input frequency is outside the capture range, the combined output (carrier detector function) is at a LOW level
(any voltage below 0.6V
CC
). When the PLL becomes locked, the voltage at pin 19 rises to a HIGH level
(V
19
= 0.8V
CC
to V
CC
). When the input channel is close to the centre frequency, V
19
falls to the LOW level. As shown
in Fig.3, the voltage at pin 19 is now a function of the centre frequency (AFC function). This information may be read
by a microcontroller via the ADC of the satellite frequency synthesizer (TSA5055) and the I
2
C-bus.
16. This current discharges the external capacitors between two energy dispersal peak values and avoid the use of
external resistors in parallel with capacitors.
17. The drift of the automatic frequency control voltage is measured in accordance with the following method:
a) At room temperature (T
amb
= 25
C) the TDA8012AM is driven by a 480 MHz unmodulated signal. The voltage at
pin 20 must be adjusted to obtain a 1.5 V output at the AFC output (pin 19).
b) At T
amb
= 80
C, due to its temperature drift, the AFC output voltage differs from 1.5 V. The input frequency must
be adjusted to obtain 1.5 V at the AFC output. Then the VCO frequency f
VCO
is measured in free running mode
(without input signal). The drift of the automatic frequency control voltage will then be equal to the difference
between the input frequency and f
VCO
.
Fig.3 AFC and carrier detector output.
handbook, full pagewidth
MBH932
0
frequency
0.15
0.3
0.45
0.6
0.8
1
AFC DATA
V19
VCC
carrier detect on
f o
500 kHz
1997 May 26
10
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
APPLICATION INFORMATION
Fig.4 Application circuit.
(1) 2.5 turns; diameter 2.0 mm.
(2) T1, T2 = BC547B.
handbook, full pagewidth
MBH933
3
4
STABILIZER
VCO
VIDEO BUFFER
TDA8012AM
1
2
5
6
7
8
9
10
CC
V
AGCO
Vth(AGC)
1 nF
video
KEY
AFC/CDO
20
19
18
17
16
15
14
13
12
A
11
CARRIER
DETECTOR
AFC
AGC
82 k
2.7 M
22
F
1
F
330 nF
330 nF
intermediate
frequency
input
10 nF
10 nF
4.7
k
2.7
k
1.5 k
330
330 nF
470
F
75
680
15 k
T1
(2)
T2
(2)
+
15 V
-
15 V
1 nF
47
F
8.2 pF
3.3 pF
(1)
220 pF
10
k
4.7 k
CC
V
1997 May 26
11
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
PACKAGE OUTLINE
UNIT
A
1
A
2
A
3
b
p
c
D
(1)
E
(1)
(1)
e
H
E
L
L
p
Q
Z
y
w
v
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
EIAJ
mm
0.15
0
1.4
1.2
0.32
0.20
0.20
0.13
6.6
6.4
4.5
4.3
0.65
1.0
0.2
6.6
6.2
0.65
0.45
0.48
0.18
10
0
o
o
0.13
0.1
DIMENSIONS (mm are the original dimensions)
Note
1. Plastic or metal protrusions of 0.20 mm maximum per side are not included.
0.75
0.45
SOT266-1
90-04-05
95-02-25
w
M
A
A
1
A
2
b
p
D
H
E
L
p
Q
detail X
E
Z
e
c
L
v
M
A
X
(A )
3
A
y
0.25
1
10
20
11
pin 1 index
0
2.5
5 mm
scale
SSOP20: plastic shrink small outline package; 20 leads; body width 4.4 mm
SOT266-1
A
max.
1.5
1997 May 26
12
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
"IC Package Databook" (order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SSOP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
C.
Wave soldering
Wave soldering is not recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
C within
6 seconds. Typical dwell time is 4 seconds at 250
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
C.
1997 May 26
13
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
DEFINITIONS
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
1997 May 26
14
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
NOTES
1997 May 26
15
Philips Semiconductors
Product specification
Low power PLL FM demodulator for
satellite TV receivers
TDA8012AM
NOTES
Internet: http://www.semiconductors.philips.com
Philips Semiconductors a worldwide company
Philips Electronics N.V. 1997
SCA54
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 So Paulo, SO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstrae 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Printed in The Netherlands
547047/1200/01/pp16
Date of release: 1997 May 26
Document order number:
9397 750 01589
PDF 
ZIP