ChipFind - документация

Электронный компонент: PLL701-0XSCLR

Скачать:  PDF   ZIP
PLL701-01/02/04/06
Low EMI Spread Spectrum Multiplier Clock
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991
www.phaselink.com
Rev 08/30/05 Page 1
FEATURES
Spread Spectrum Clock Generator with selectable
multiplier from 1x to 6x outputs.
Output frequency ranges: 10MHz to 180MHz.
Accepts input from crystal or reference clock.
Selectable Center, Down or Asymmetric Spread
Modulation.
Selectable Modulation rate.
TTL/CMOS compatible outputs.
3.3V Operating Voltage.
Low short term jitter.
Available in 8-Pin 150mil SOIC.
DESCRIPTION
The PLL701-01/02/04/06 are Spread Spectrum Clock
Generators designed for the purpose of reducing EMI
in high-speed digital systems. Any output frequency
from 10 to 180MHz can be selected by programming
6 multiplier modes. The device is designed to operate
from a crystal or reference clock input and provides
1x to 6x modulated clock outputs.
PIN CONFIGURATION
Note: ^: Internal pull-up resistor (120k
for SD, 30 k for
SC0-SC2).
*: The value of SD is latched upon power-up. The
internal pull-up resistor results in a default high value
when no pull-down resistor is connected to this pin
(recommended external pull-down resistor of 27 k
).
OUTPUT CLOCK (FOUT) SELECTION
SST Modulation
SD SC2 SC1 SC0
FOUT
(-01)
FOUT
(-02)
FOUT
(-04)
FOUT
(-06)
Magnitude Freq.
Type
1 0 0 0 X1 X2 X4 X6 0.50%
C
0.25%
1 0 0 1 X1 X2 X4 X6
C
0.5%
0 0 0 1 X1 X2 X4 X6
1.00%
D -1.0%
1 0 1 0 X1 X2 X4 X6
C
0.75%
0 0 1 0 X1 X2 X4 X6
1.50%
A +0.25%
~
-1.25%
1 0 1 1 X1 X2 X4 X6
C
1.0%
0 0 1 1 X1 X2 X4 X6
2.00%
A
+0.5% ~ -1.5%
1 1 0 0 X1 X2 X4 X6
C
1.25%
0 1 0 0 X1 X2 X4 X6
2.50%
A +0.75%
~
-1.75%
1 1 0 1 X1 X2 X4 X6
C
1.5%
0 1 0 1 X1 X2 X4 X6
3.00%
A +1.0%
~
-2.0%
1 1 1 0 X1 X2 X4 X6
C
1.75%
0 1 1 0 X1 X2 X4 X6
3.50%
A +1.25%
~
-2.25%
1 1 1 1 X1 X2 X4 X6 OFF
Fin / 512
Notes: C: Center Spread. A: Asymmetric Spread. D: Down Spread.
PLL701-0X
1
2
3
4
5
6
7
8
XIN/FIN
XOUT/SD*^
SC0^
SC1^
VDD
FOUT
GND
SC2^
XIN/FIN = 10 ~ 30 MHz
PLL701-01/02/04/06
Low EMI Spread Spectrum Multiplier Clock
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 www.phaselink.com Rev 08/12/04 Page 2
BLOCK DIAGRAM
PIN DESCRIPTIONS
Name Number
Type
Description
XIN/FIN 1 I
Crystal input to be connected to fundamental parallel mode crystal.(C
L
=18pF) or
clock input.
XOUT/SD 2 B
At power-up, this pin is an input pin to select modulation type. After input
sampling, this pin is crystal output. Has internal pull up resistor.
SC0
3
I
Digital control input to select modulation magnitude. Has internal pull-up.
SC1
4
I
Digital control input to select modulation magnitude. Has internal pull-up.
GND 5 P
Ground.
FOUT 6 O
Modulated Clock Frequency Output. The frequency before modulation is
synthesized by multiplying the input frequency by 1X, 2X, 4X, 6X depending on
the part number (PLL701-01, -02, -04, -06).
SC2
7
I
Digital control input to select modulation magnitude. Has internal pull-up.
VDD 8 P
Power
Supply.
FUNCTIONAL DESCRIPTION
Selectable spread spectrum and modulation magnitudes
The PLL701-01/02/04/06 provides selectable spread spectrum modulation type, as well as selectable modulation
magnitude. Selection is made by connecting specific pins to a logical "zero" or "one" according to the output clock
selection table on page 1.

In order to reduce the number of pins on the chip, the PLL701-01/02/04/06 uses pin 2 (XOUT/SD) as a bi-
directional pin. The pin serves as modulation type selector input (SD) upon power-up (see output clock selection
table on page 1), and as XOUT crystal connection as soon as the input has been latched.
Pins 3 (SC0), 4 (SC1), and 7 (SC2) are used as inputs to select the spread spectrum modulation magnitude as
shown on the output clock selection table (page 1).
XTAL
OSC
FOUT
XIN/FIN
XOUT
SC(0:2)
PLL
SST
Control
Logic
PLL701-01/02/04/06
Low EMI Spread Spectrum Multiplier Clock
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 www.phaselink.com Rev 08/12/04 Page 3
Connecting a selection pin to a logical "one"
All selection pins have an internal pull-up resistor (30k
for pins 3, 4, 7, and 120k for pin 2). This internal pull-up
resistor will pull the input value to a logical "one" (pull-up) by default, i.e. when no resistive load is connected
between the pin and GND. No external pull-up resistor is therefore required for connecting a logical "one" upon
power-up.
Connecting a selection pin to a logical "zero"
For an input only pin, i.e. pins 3 (SC0), 4 (SC1), and 7 (SC2), the pin simply needs to be grounded to pull the input
down to a logical "zero". Connecting the bi-directional pin (SD) to a logical "zero" will however require the use of a
27k
loading resistor between the pin and GND.
ELECTRICAL SPECIFICATIONS
1. Absolute Maximum Ratings
PARAMETERS SYMBOL
MIN.
MAX.
UNITS
Supply Voltage
V
DD
4.6 V
Input Voltage, dc
V
I
-0.5
V
DD
+0.5 V
Output Voltage, dc
V
O
-0.5
V
DD
+0.5 V
Storage Temperature
T
S
-65 150
C
Ambient Operating Temperature*
T
A
-40 85
C
Junction Temperature
T
J
125
C
Lead Temperature (soldering, 10s)
260
C
ESD Protection, Human Body Model
2
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the
device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other
conditions above the operational limits noted in this specification is not implied.
* Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
2. Timing Characteristics
PARAMETERS SYMBOL
CONDITIONS
MIN.
TYP.
MAX.
UNITS
Rise Time
T
r
Measured at 0.8V ~ 2.0V @ 3.3V
0.8
0.95
1.1
ns
Fall Time
T
f
Measured at 2.0V ~ 0.8V @ 3.3V
0.78
0.85
0.9
ns
Output Duty Cycle
D
T
45 50 55 %
Cycle to Cycle Jitter
T
cyc-cyc
FOUT=48MHz @ 3.3V
100
ps
Cycle to Cycle Jitter
T
cyc-cyc
FOUT=72MHz @ 3.3V
100
ps
PLL701-01/02/04/06
Low EMI Spread Spectrum Multiplier Clock
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 www.phaselink.com Rev 08/12/04 Page 4
3. DC/AC Specifications
PARAMETERS SYMBOL CONDITIONS MIN.
TYP.
MAX.
UNITS
Supply Voltage
V
DD
2.97 3.63 V
Input High Voltage
V
IH
0.7*VDD
V
Input Low Voltage
V
IL
0.3*VDD
V
Input High Current
I
IH
100
A
Input Low Current
I
IL
100
A
Output High Voltage
V
OH
I
OH
=5mA,
VDD=3.3V
2.4
Output Low Voltage
V
OL
I
OL
=6mA,
VDD=3.3V 0.4
F
XIN
When using a crystal
10
30
MHz
Input Frequency
F
IN
When using reference clock
10
30
MHz
Maximum interruption of F
IN
When using reference clock
100
s
Load Capacitance
C
L
Between Pin XIN and
XOUT*
18 pF
Pull-up Resistor
R
up
PIN
2
120 k
Pull-up Resistor
R
up
PIN 3, 4, 7
30
k
Short Circuit Current
I
sc
50 mA
3.3V Dynamic Supply Current
I
CC
No
Load
20 mA
*Note: Pin XIN and XOUT each has a 36pF capacitance. When used with a XTAL, the two capacitors combined load the crystal with 18pF. If driving XIN
with a reference clock signal, the load capacitance will be 36pF (typical).
PLL701-01/02/04/06
Low EMI Spread Spectrum Multiplier Clock
47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990 FAX (510) 492-0991 Rev 05/07/03 Page 5
PACKAGE INFORMATION

ORDERING INFORMATION
PhaseLink Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information
furnished by Phaselink is believed to be accurate and reliable. However, PhaseLink makes no guarantee or warranty concerning the accuracy of said
information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product.

LIFE SUPPORT POLICY: PhaseLink's products are not authorized for use as critical components in life support devices or systems without the
express written approval of the President of PhaseLink Corporation.
For part ordering, please contact our Sales Department:
47745 Fremont Blvd., Fremont, CA 94538, USA
Tel: (510) 492-0990 Fax: (510) 492-0991
PART NUMBER
The order number for this device is a combination of Device number, Package type and Operating temperature range
PLL701-0X X C X R
Part / Order Number
Marking
Package Option
Temperature
PLL701-0XSCR
P701-0XXC
SOIC -Tape and Reel
0 to +70C
PLL701-0XSC P701-0XXC
SOIC
-Tube
0 to +70C
PLL701-0XSCLR P701-0XXCL SOIC -Tape and Reel (GREEN)
0 to +70C
PLL701-0XSCL
P701-0XXCL
SOIC Tube (GREEN)
0 to +70C
C
L
A
8 PIN Narrow SOIC ( mm )
SOI
C
Symbol
Min.
Max
.
A
1.47
1.73
A1
0.10
0.25
B
0.33
0.51
C
0.19
0.25
D
4.80
4.95
E
3.80
4.00
H
5.80
6.20
L
0.38
1.27
e
1.27 BSC
E
H
D
A1
e
B
PART NUMBER
TEMPERATURE
C=COMMERCIAL,
I=INDUSTRIAL
PACKAGE TYPE
S=SOIC
NONE=NORMAL PACKAGE
L=GREEN PACKAGE
NONE= TUBE
R=TAPE AND REEL
FAMILY DESIGNATOR