PHASE CONTROL THYRISTOR
AT607
Repetitive voltage up to
800
V
Mean on-state current
2585
A
Surge current
36
kA
FINAL SPECIFICATION
feb 97 - ISSUE : 03
Symbol
Characteristic
Conditions
Tj
[C]
Value
Unit
BLOCKING
V
RRM
Repetitive peak reverse voltage
140
800
V
V
RSM
Non-repetitive peak reverse voltage
140
900
V
V
DRM
Repetitive peak off-state voltage
140
800
V
I
RRM
Repetitive peak reverse current
V=VRRM
140
100
mA
I
DRM
Repetitive peak off-state current
V=VDRM
140
100
mA
CONDUCTING
I
T (AV)
Mean on-state current
180 sin, 50 Hz, Th=55C, double side cooled
2585
A
I
T (AV)
Mean on-state current
180 sin, 50 Hz, Tc=85C, double side cooled
2420
A
I
TSM
Surge on-state current
sine wave, 10 ms
140
36
kA
I t
I t
without reverse voltage
6480 x1E3
As
V
T
On-state voltage
On-state current =
6000 A
25
1.55
V
V
T(TO)
Threshold voltage
140
0.8
V
r
T
On-state slope resistance
140 0.120
mohm
SWITCHING
di/dt
Critical rate of rise of on-state current, min.
From 75% VDRM up to 2600 A, gate 10V 5ohm 140
200
A/s
dv/dt
Critical rate of rise of off-state voltage, min.
Linear ramp up to 70% of VDRM
140
500
V/s
td
Gate controlled delay time, typical
VD=100V, gate source 25V, 10 ohm , tr=.5 s
25
3
s
tq
Circuit commutated turn-off time, typical
dV/dt = 20 V/s linear up to 75% VDRM
250
s
Q rr
Reverse recovery charge
di/dt=-20 A/s, I= 1730 A
140
C
I rr
Peak reverse recovery current
VR= 50 V
A
I
H
Holding current, typical
VD=5V, gate open circuit
25
300
mA
I
L
Latching current, typical
VD=5V, tp=30s
25
700
mA
GATE
V
GT
Gate trigger voltage
VD=5V
25
3.5
V
I
GT
Gate trigger current
VD=5V
25
200
mA
V
GD
Non-trigger gate voltage, min.
VD=VDRM
140
0.25
V
V
FGM
Peak gate voltage (forward)
30
V
I
FGM
Peak gate current
10
A
V
RGM
Peak gate voltage (reverse)
5
V
P
GM
Peak gate power dissipation
Pulse width 100 s
150
W
P
G
Average gate power dissipation
2
W
MOUNTING
R
th(j-h)
Thermal impedance, DC
Junction to heatsink, double side cooled
21
C/kW
R
th(c-h)
Thermal impedance
Case to heatsink, double side cooled
6
C/kW
T
j
Operating junction temperature
-30 / 140
C
F
Mounting force
22.0 / 24.5
kN
Mass
520
g
ORDERING INFORMATION : AT607 S 08
standard specification
VDRM&VRRM/100
Via N. Lorenzi 8 - I 16152 GENOVA - ITALY
Tel. int. +39/(0)10 6556549 - (0)10 6556488
Fax Int. +39/(0)10 6442510
Tx 270318 ANSUSE I -
ANSALDO
Ansaldo Trasporti s.p.a.
Unita' Semiconduttori
AT607 PHASE CONTROL THYRISTOR
FINAL SPECIFICATION feb 97 - ISSUE : 03
Cathode terminal type DIN 46244 - A 4.8 - 0.8
Gate terminal type AMP 60598 - 1
Distributed by
ON-STATE CHARACTERISTIC
Tj = 140 C
0
1000
2000
3000
4000
5000
6000
7000
8000
0.6
1.1
1.6
On-state Voltage [V]
On-state Current [A]
TRANSIENT THERMAL IMPEDANCE
DOUBLE SIDE COOLED
0.0
5.0
10.0
15.0
20.0
25.0
0.001
0.01
0.1
1
10
100
t[s]
Zth j-h [C/kW]
SURGE CHARACTERISTIC
Tj = 140 C
0
5
10
15
20
25
30
35
40
1
10
100
n cycles
ITSM [kA]
ANSALDO
All the characteristics given in this data sheet are guaranteed only with uniform
clamping force, cleaned and lubricated heatsink, surfaces with flatness < .03
mm and roughness < 2 m.
In the interest of product improvement ANSALDO reserves the right to change
any data given in this data sheet at any time without previous notice.
If not stated otherwise the maximum value of ratings (simbols over shaded
background) and characteristics is reported.
PDF 
ZIP
