1
HAS SERIES - 30 WATT
REV. 0
9/01
Industry Standard
Half-Brick
Low-Cost Design
100C Baseplate
Operation
Open-Frame Packaging
24V and 48V Input
Versions
Input Pi Filter
Optional Enable Logic
1500V Isolation
FEATURES
HAS DC/DC converters provide up to 30 watts of
output power in an industry-standard package and
footprint. With a maximum case temperature of
100C, the HAS is well suited for the most
demanding telecom, networking, and industrial
applications. The HAS features 1500 VDC isolation,
short circuit, and overtemperature protection, as well
as six-sided shielding. The HAS series is available
with optional enable and voltage trim pins. Please see
the IAD series for dual output applications.
DESCRIPTION
TECHNICAL SPECIFICATIONS
Voltage Range
24 VDC Nominal
18 - 36 VDC
48 VDC Nominal
36 - 75 VDC
Reflected Ripple
50 mA
Input
Setpoint Accuracy
1%
Line Regulation Vin Min. - Vin Max., Iout Rated
0.2% Vout
Load Regulation Iout Min. - Iout Max., Vin Nom.
0.2% Vout
Remote Sense Headroom
0.5 VDC
Minimum Output Current
10 %
Dynamic Regulation, Loadstep
25% Iout
Pk Deviation
4% Vout
Settling Time
500
s
Voltage Trim Range
10%
Short Circuit / Overcurrent Protection
Hiccup
Current Limit Threshold Range, % of Iout Rated
110 - 140%
OVP Trip Range
115 - 140% Vout Nom.
Remote Shutdown Reference
Vin Negative
Shutdown Pin Current, Sourced At Off
10 mA Max.
Output
General
Turn-On Time
10 mS
Remote Shutdown
Positive/Negative Logic
Switching Frequency
250 kHz
Isolation
Input - Output
1500 VDC
Input - Case
1050 VDC
Output - Case
500 VDC
Temperature Coefficient
0.03%/C
Case Temperature
Operating Range
-40 To +100C
Storage Range
-40 To +125C
Humidity Max., Non-Condensing
95%
Vibration, 3 Axes, 5 Min Each
5 g, 10 - 55 Hz
MTBF (Bellcore TR-NWT-000332)
2.5 X 106 hrs
Safety
UL, cUL, TUV
Weight (Approx.)
1.4 oz
50
55
60
65
70
75
80
85
90
95
10
20
30
40
50
60
70
80
90
100
LOAD %
EFFICIENCY %
HAS030ZH-A
HAS030ZG-A
HAS030ZJ-A
HAS030YG-A
60
65
70
75
80
85
90
10
20
30
40
50
60
70
80
90
100
LOAD %
EFFICIENCY %
EFF. (18v)
EFF. (24v)
EFF. (36v)
Efficiency vs. Load (48V Input)
Efficiency vs. Load (24V Input)
Notes
MTBF predictions may vary slightly from model to model.
Specifications typically at 25C, normal line, and full load, unless
otherwise stated.
Soldering Conditions: I/O pins, 260C, ten seconds; fully
compatible with commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please
consult factory for specific model information.
Units are water-washable and fully compatible with commercial spray or
immersion post wave-solder washing equipment.
3
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add
them to the model number. Example ordering options are located below the options table.
OPTION
SUFFIX
APPLICABLE SERIES
REMARKS
Negative Logic
N
HAS, HBD, HBS, HES, HLS, LES,
QBS, QES, QLS, TES, TQD
TTL Low Turns Module ON
TTL High Turns Module OFF
Lucent-Compatible Trim
T
HAS, HBD, HBS, HES, HLS, QBS,
QES, QLS
Terminal Strip
TS
XWS, XWD, XWT
Trim
1
IAS, LES
Enable
2
IAD, IAS, LES, SMS
Trim and Enable
3
IAS, LES
Current Share
4
SMS
Headerless
Y
Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
Standard Pin Length is 0.180
(4.6mm)
0.110 (2.8mm) Pin Length
8
All Units (Except SMS)
0.150 (3.8mm) Pin Length
9
All Units (Except SMS)
0.24 (6.1mm) Horizontal Heatsink
1H
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.24 (6.1mm) Vertical Heatsink
1V
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.45 (11.4mm) Horizontal
Heatsink
2H
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.45 (11.4mm) Vertical Heatsink
2V
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.95 (24.1mm) Horizontal
Heatsink
3H
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.95 (24.1mm) Vertical Heatsink
3V
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
Example Options:
HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95 vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110 pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
OPTIONS
PDF 
ZIP