1
HAS060ZH-A
45
50
55
60
65
70
75
80
85
90
10
20
30
40
50
60
70
80
90
100
LOAD %
EFFICIENCY %
EFF. (36v)
EFF. (48v)
EFF. (72v)
HAS060YH-A
60
65
70
75
80
85
90
10
20
30
40
50
60
70
80
90
100
LOAD %
EFFICIENCY
%
EFF. (18v)
EFF. (24v)
EFF. (36v)
Industry Standard
Half-Brick
Low-Cost Design
Open-Frame Packaging
100C Baseplate Operation
24V and 48V Inputs
Optional Enable Logic
1500V Isolation
Input Pi Filter
General
DESCRIPTION
FEATURES
Notes
MTBF predictions may vary slightly from model to model.
Specifications typically at 25C, normal line, and full load, unless otherwise
stated.
Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult
factory for specific model information.
Units are water-washable and fully compatible with commercial spray or
immersion post wave-solder washing equipment.
Efficiency vs. Load (48V Input)
Efficiency vs. Load (24V Input)
Voltage Range
24 VDC Nominal
18 - 36 VDC
48 VDC Nominal
36 - 72 VDC
Reflected Ripple
25 mA
Input Reverse Voltage Protection
Shunt Diode
Input
TECHNICAL SPECIFICATIONS
Output
Setpoint Accuracy
1%
Line Regulation V
in
Min. - V
in
Max., I
out
Rated
0.2% V
out
Load Regulation I
out
Min. - I
out
Max., V
in
Nom.
0.2% V
out
Remote Sense Headroom
0.5 VDC
Minimum Output Current
10 % I
out
Rated
Dynamic Regulation, Loadstep
25% I
out
Pk Deviation
4% V
out
Settling Time
500
s
Voltage Trim Range
10%
Short Circuit / Overcurrent Protection
Hiccup
Current Limit Threshold Range, % of I
out
Rated
110 - 140%
OVP Trip Range
115 - 140% V
out
Nom.
Remote Shutdown Reference
V
in
Negative
Shutdown Pin Current, Sourced at Off
10 mA Max.
HAS SERIES - 60 WATT
HAS DC/DC converters are low-cost, industry standard,
half-brick converters. The HAS features 2:1 input
voltage, excellent efficiency, and open-frame packaging
technology. The HAS operates over a range of -40C to
100C and has a built-in input pi filter that helps to
ensure low noise operation. Available in several input
and output combinations, the HAS is designed for
industrial, telecom, and networking applications.
Turn-On Time
10 ms
Remote Shutdown
Positive or Negative Logic
Switching Frequency
500 kHz
Isolation
Input - Output
1500 VDC
Input - Case
1050 VDC
Output - Case
500 VDC
Temperature Coefficient
0.03%/C
Case Temperature
Operating Range
-40 To +100C
Storage Range
-40 To +125C
Thermal Shutdown Range
105 To 115C
Humidity Max., Non-Condensing
95%
Vibration, 3 Axes, 5 Min Each
5 g, 10 - 55 Hz
MTBF
(Bellcore TR-NWT-000332)
2.5 x 106 hrs
Safety
UL, cUL, TUV
Weight (approx.)
1.4 oz
REV. 09/01
3
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add
them to the model number. Example ordering options are located below the options table.
OPTION
SUFFIX
APPLICABLE SERIES
REMARKS
Negative Logic
N
HAS, HBD, HBS, HES, HLS, LES,
QBS, QES, QLS, TES, TQD
TTL Low Turns Module ON
TTL High Turns Module OFF
Lucent-Compatible Trim
T
HAS, HBD, HBS, HES, HLS, QBS,
QES, QLS
Terminal Strip
TS
XWS, XWD, XWT
Trim
1
IAS, LES
Enable
2
IAD, IAS, LES, SMS
Trim and Enable
3
IAS, LES
Current Share
4
SMS
Headerless
Y
Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
Standard Pin Length is 0.180
(4.6mm)
0.110 (2.8mm) Pin Length
8
All Units (Except SMS)
0.150 (3.8mm) Pin Length
9
All Units (Except SMS)
0.24 (6.1mm) Horizontal Heatsink
1H
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.24 (6.1mm) Vertical Heatsink
1V
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.45 (11.4mm) Horizontal
Heatsink
2H
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.45 (11.4mm) Vertical Heatsink
2V
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.95 (24.1mm) Horizontal
Heatsink
3H
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.95 (24.1mm) Vertical Heatsink
3V
All Units (Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
Example Options:
HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95 vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110 pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
OPTIONS
PDF 
ZIP