ChipFind - документация

Электронный компонент: IAD012ZJJ

Скачать:  PDF   ZIP
(888) IPD-CONVerters
q
(888) 473-2668
q
www.ipdconverters.com
C-70
50
55
60
65
70
75
80
85
90
10
20
30
40
50
60
70
80
90
100
LOAD %
EFFICIENCY
%
EFF. IAD010ZGG
EFF. IAD012ZHH
EFF. IAD012ZJJ
DESCRIPTION
FEATURES
IAD SERIES - DUAL OUTPUT, 12 WATT
Industry Standard
Package
Industry Standard
Footprint
Fixed Frequency Design
100C Case Operation
Optional Trim and
Enable
Wide Range Input
1500V Isolation
Short Circuit Protection
IAD dual output DC/DC converters provide up to 12
Watts of output power in an industry standard package
and footprint. With a maximum case temperature of
100C, the IAD is well suited for the most demanding
applications. The IAD features 1500 VDC isolation,
short circuit, and overtemperature protection, as well as
six-sided shielding. The IAD is available with optional
enable and voltage trim pins. Please see the IAS series for
single output applications.
Efficiency vs. Load (48V Input)
General
Turn-On Time
300 ms
Remote Shutdown
Positive Logic
Switching Frequency
400 kHz
Isolation
Input - Output
1500 VDC
Output - Case (for 48 V
in
)
500 VDC
Input - Case (for 24 V
in
)
1050 VDC
Temperature Coefficient
0.03%/C
Case Temperature
Operating Range
-40 To +85C
Storage Range
-40 To +110C
Humidity Max., Non-Condensing
95%
Vibration, 3 Axes, 5 Min Each
5 g, 10 - 55 Hz
MTBF
(Bellcore TR-NWT-000332)
1.8 X 10
6
hrs
Safety
UL, CUL, VDE
Weight (Approx.)
1.2 oz
Notes
MTBF predictions may vary slightly from model to model.
Industrial temp range available
Specifications typically at 25C, normal line, and full load, unless otherwise stated.
Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory
for specific model information.
Units are water-washable and fully compatible with commercial spray or immersion
post wave-solder washing equipment.
TECHNICAL SPECIFICATIONS
Voltage Range
24 VDC Nominal
18 - 36 VDC
48 VDC Nominal
34 - 75 VDC
Reflected Ripple
25 mA
Input Reverse Voltage Protection
Shunt Diode
Input
Output
Setpoint Accuracy
1%
Auxillary Setpoint Accuracy
5 %
Line Regulation V
in
Min. - V
in
Max., I
out
Rated
0.5% V
out
Load Regulation I
out
Min. - I
out
Max., V
in
Nom.
1.0% V
out
Minimum Output Current
10 % I
out
Rated
Dynamic Regulation, Loadstep
25% I
out
Pk Deviation
4% V
out
Settling Time
500
s
Voltage Trim Range
10%
Short Circuit / Overcurrent Protection
Hiccup
Power Limit Threshold Range
110 - 150%
C-71
Thermal Impedance
Natural Convection
15.4 C/W
100 LFM
12.2 C/W
200 LFM
9.3 C/W
300 LFM
7.4 C/W
400 LFM
6.4 C/W
Note:
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated
for specific application.
IAD SERIES - DUAL OUTPUT, 12 WATT
MECHANICAL DRAWING
1
+V
in
2
-V
in
3
Optional
Shutdown
4
+V
out
5
Common
6
-V
out
Pin
Function
Tolerances
Inches: (Millimeters)
.XX 0.020 .X 0.5
.XXX 0.010 .XX 0.25
Pin:
0.002 0.05
Case:
+ 0.04, - 0.00 + 1.0, - 0.0
(Tolerances as listed unless otherwise specified.)
MODELS - (See the last page of this file for options.)
Vin
(Volts)
Vin Range
(Volts)
Iin Max.*
(Amps)
Vout
(Volts)
Iout Rated
(Amps)
Ripple & Noise
Pk-Pk (mV)
Efficiency
Typ. **
Model
24
24
24
48
48
48
18 - 36
18 - 36
18 - 36
34 - 75
34 - 75
34 - 75
0.80
0.85
0.85
0.40
0.43
0.42
5
12
15
5
12
15
1.0
0.5
0.4
1.0
0.5
0.4
75
120
150
75
120
150
77%
82%
83%
78%
82%
83%
IAD010YGG
IAD012YHH
IAD012YJJ
IAD010ZGG
IAD012ZHH
IAD012ZJJ
Denotes advanced product release. Consult factory for product availability.
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
DIA 0.040"
(1.0mm)
0.18" MIN.
(4.6mm)
0.42"
(10.7mm)
1.00"
(25.4mm)
2.00"
(50.8mm)
0
0.800"(20.3mm)
BOTTOM VIEW
1.40"(35.6mm)
3
2
1
4
6
5
0
0.300"
(7.6mm)
0.400"
(10.2mm)
0.500"
(12.7mm)
0.800"
(20.3mm)
0.900"
(22.9mm)
C105
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that
you prefer and add them to the model number. Example ordering options are located below the
options table.
OPTION
SUFFIX
APPLICABLE SERIES
REMARKS
Negative Logic
N
HAS, HBD, HBS, HES, LES, QBS,
QES, TES, TQD
TTL "Low" Turns Module ON
TTL "High" Turns Module OFF
Lucent Compatible Trim
T
HAS, HBD, HBS, HES, QBS, QES
Terminal Strip TS XWS, XWD, XWT
Trim
1
IAS, LES
Enable
2
IAD, IAS, LES, SMS
Trim and Enable
3
IAS, LES
Current Share
4
SMS
Headerless
Y
Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK
OPTIONS
Standard Pin Length is 0.180"
(4.6mm)
0.110" (2.8mm) Pin Length
8
All Units (Except SMS)
0.150" (3.8mm) Pin Length
9
All Units (Except SMS)
0.24" (6.1mm) Horizontal Heatsink
1H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.24" (6.1mm) Vertical Heatsink
1V
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.45" (11.4mm) Horizontal
Heatsink
2H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.45" (11.4mm) Vertical Heatsink
2V
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.95" (24.1mm) Horizontal
Heatsink
3H
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
0.95" (24.1mm) Vertical Heatsink
3V
All Units (Except DIP, SIP, and SM
Packages)
Includes Thermal Pad
Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and
0.95" vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110" pin length.
NUCLEAR AND MEDICAL APPLICATIONS
Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS
The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.